Bedienungsanleitung BeF Home Passive - HOT AIR FIREPLACE INSERTS (Seite 6 von 9) (Englisch)

810623

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

________________________________________________________________________________________________________________________________

Firma: BeF Home, s.r.o. Strana 6 (celkem 9) Platí od: 1. 4. 2014

Vydání: 4

There must be a safety pin on the smoke flue bellmounth to prevent slippage or turning out!

Fireplace insert with pull-up system door must be veneered to allow service and repair works. Veneer in the top part above the door of

fireplace must be built up from easy demountable material (Calsil etc.), or there must be service opening in the place of bearing (grilles,

thinning of coating etc.). Frame in the front part of insert with pull-up system must be built-in in accordance with scheme (pict. 4). It allows

later demounting in case of pull up system service. Holes in the cover of the pull-up system have to be through so the air can pass and carry

out the cooling of mechanism.

Pict.4

Convection air holes:

In the top part of the surround, it is necessary to provide non closable convection air holes for a convection air output, in the bottom part, there

is a need of convectional air input - minimal diameter depends on output of the fireplace insert, mentioned in the Equipment certificate. You

need to consider non effective parts of the grilles (20-40% of the grille area, depending on design also) when choosing the convenient grilles

for input/output of the convectional air and take into account also way of the using (in Equipment certificate, nominal output of the fireplace

insert is mentioned and the real output depends on the amount of wood in use, the real output can be for short period higher of 50%). The

minimal dimensions of the convectional air grilles for input and output are mentioned in the following chart:

Fireplace insert output (kW)

Convectional air input (cm2) – grille

dimension

Convectional air output – grille dimension

(cm2)

6-9

700

1000

10-15

850

1200

15-20

1100

1600

After the fireplace installation neither the air input nor the air vents can be restricted by building panels.

We recommend ordering a professional firm.

To prevent heat accumulation, the holes for convectional air must be open during heating. No lockable grates, ribs, blinds etc. can be installed

into the holes. In the top part the convection coating must be finished by the partition wall above the hole so as not to make a thermal pocket

(See surround diagram).

Convection cross-section between the insert and the coating as well as the insulation on the rear side – please check the chart with

measures of protection (see p.6)

Note: These minimal distances in accordance with the Equipment Certificate must be kept to on all heights and widths of the fireplace

insert so as to allow convection air to flow through.

To prevent accumulation of heat must be input and output grids convection air during heating operation still opening.

 Convection air area: If a prefabricated area for convection air is not used (lining made of a galvanized sheet), it is necessary to maintain a

distance according to the chart on page n.4 between the fireplace insert and rear thermal insulation layer.

 The fireplace insert assembly: The fireplace insert can be placed on a fitted base after the making of the thermal insulation as in the

installation instructions. The fireplace insert is connected with the chimney by the connecting piece (smoke flue).

 Extension joint: It is necessary to have an extension joint at least 3 mm thick between the insert and the coating. The extension joint can

be stemmed by a rope or sealing tape.

RÁMEČEK

PRVEK OBEZDÍVKY

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BeF Home Passive - HOT AIR FIREPLACE INSERTS Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info