660464

Behringer Xenyx QX1002USB Seite 6

6
Zoom out
Zoom in
Vorherige Seite
1/15
Nächste Seite
6 XENYX QX1202USB/QX1002USB User Manual
GAIN
Use the GAIN control to adjust the input gain. This control should always be
turned fully counterclockwise whenever you connect or disconnect a signal
source to one of the inputs.
The scale has 2 dierent value ranges: the rst value range (+10 to +60 dB)
refers to the MIC input and shows the amplication for the signals fed in there.
The second value range (-10 to +40 dBu) refers to the line input and shows
its sensitivity. The settings for equipment with standard line-level signals
(-10dBVor +4 dBu) look like this: While the GAIN control is turned all the way
down, connect your equipment. Set the GAIN control to the external devices’
standard output level. If that unit has an output signal level display, it should
show 0 dB during signal peaks. For +4dBu, turn up GAIN slightly, for-10dBV a
bit more. Tweaking is done using the CLIP LED.
COMP
Use the COMP knob to adjust the amount of compression eect on the channel.
Compression limits the dynamic range of the audio source, which can help vocals
cut through a mix better, for example. Turn the COMP knob clockwise until the
adjacent LED occasionally lights during speech/singing.
EQ
All mono input channels include a 3-band equalizer. All bands provide boost or
cut of up to 15 dB. In the central position, the equalizer is inactive.
The circuitry of the British EQs is based on the technology used in the best-known
top-of-the-line consoles and providing a warm sound without any unwanted
side eects. The result are extremely musical equalizers which, unlike simple
equalizers, cause no side eects such as phase shifting or bandwidth limitation,
even with extreme gain settings of ±15 dB.
The upper (HIGH) and the lower band (LOW) are shelving lters that increase
or decrease all frequencies above or below their cut-o frequency. The cut-o
frequencies of the upper and lower band are 12 kHz and 80Hz respectively.
Themid band is congured as a peak lter with a center frequency of 2.5 kHz.
Unlikeshelving lters, the peak lter processes a frequency range that extends
upwards and downwards around its middle frequency.
LOW CUT
In addition, the mono channels are equipped with a steep LOW CUT lter
designed to eliminate unwanted low-frequency signal components. Thesecan
be noises created by hand-held microphones, subsonicnoise or plosive sounds
created by highly sensitivemicrophones.
FX
FX sends enable you to feed signals via a variable control from one or more
channels and sum these signals to a bus. The bus appears at the console’s FX send
output and can be fed from there to an external eects device. The return from
the eects unit is then brought back into the console on the stereo channels.
Each FX send is mono and features up to +15 dB gain.
As the name suggests, the FX sends of the XENYX mixing consoles are intended to
drive eects devices (reverb, delay, etc.) and are therefore congured post-fader.
With XENYX mixing consoles, the channel fader is called LEVEL control.
In the QX1002/1202USB, the FX send is routed directly to the built-in eects
processor. To make sure that the eects processor receives an input signal,
youshouldn’t turn this control all the way to the left (-∞).
PAN
The PAN control determines the position of the channel signal within the stereo
image. This control features a constant-power characteristic, which means the
signal is always maintained at a constant level, irrespective of position in the
stereo panorama.
LEVEL
The LEVEL control determines the level of the channel signal in the main mix.
◊ Attention: Since the FX path for the effect processor is connected
post-fader, the LEVEL control has to be turned up in order to get this
channel’s signal to the effects processor!
CLIP
The CLIP-LED’s of the mono channels illuminate when the input signal is driven
too high, which could cause distortion. If this happens, use the GAIN control to
reduce the preamp level until the LED does not light anymore.
2.2 Stereo channels
Fig. 2.2: Connectors and controls on the stereo channels
LINE IN
Each stereo channel has two balanced line level inputs on ¼" connectors for left
and right channels. If only the connector marked “L” (left) is used, thechannel
operates in mono. Thestereo channels are designed to handle typical line level
signals. Both inputs will also accept unbalancedconnectors.
FX
The FX send of the stereo channels functions similar to that of the mono channels.
However, since the FX send bus is mono, a mono sum is rst taken from the stereo
input before it is sent to the FX bus.
… 6 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

behringer-xenyx-qx1002usb

Suche zurücksetzen

  • Wie kann man den Hall-Effekt aus- und einschalten? Eingereicht am 14-2-2023 11:18

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Behringer Xenyx QX1002USB wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Behringer Xenyx QX1002USB

Behringer Xenyx QX1002USB Kurzanleitung - Deutsch, Englisch, Französisch, Portugiesisch, Spanisch - 17 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info