660464
7
Zoom out
Zoom in
Vorherige Seite
1/15
Nächste Seite
7 XENYX QX1202USB/QX1002USB User Manual
BAL
The BAL(ANCE) control determines the levels of left and right input signals
relative to each other before both signals are then routed to the main stereo mix
bus. If a channel is operated in mono via the left line input, thiscontrol has the
same function as the PAN control used in the mono channels.
LEVEL
The LEVEL control determines the volume of the channel being sent to the
mainmix.
+4/-10
The stereo inputs of the XENYX have an input sensitivity switch which selects
between +4 dBu and -10 dBV. At -10dBV (home-recording level), the input is
more sensitive (requires less level to drive it) than at +4 dBu (studio level).
2.3 Connector array of the main section
Fig. 2.3: Connectors of the main section
FX SEND
The FX SEND connector outputs the signal you picked up from the individual
channels using the FX controls. You can connect this to the input of an external
eects device in order to process the FX bus’ master signal. Once an eects mix is
created, the processed signal can then be routed from the eects device outputs
back into a stereo input.
If the connected effects processor receives no input signal,
the FX SEND control is probably too low. This also goes for the built-in
effects processor.
Adjust your external effects processor to 100% wet (effects signal
only), because the effects signal is added to the main mix along with
the “dry” channel signals.
In this instance, the FX control of the channel being used as an effects
return should be turned fully counterclockwise, otherwise feedback
problems can occur!
PHONES/CTRL ROOM OUT
The stereo PHONES connector (at the top of the connector panel) is where
h
eadphones are connected. The balanced CTRL ROOM OUT connectors carry
the summed effects and main mix signals. ThePHONES/CONTROL ROOM
control in the main section adjusts the level of both headphones and main
monitoroutputs.
MAIN OUT
The MAIN OUT connectors are balanced mono connectors. The main mix signal
appears here at a level of 0 dBu. The MAIN MIX fader adjusts the volume of
theseoutputs.
2-TRACK INPUT
The 2-TRACK INPUTs are used to bring an external signal source (e.g. CD player,
tape deck, etc.) into the console. They can also be used as a standard stereo line
input, so the output of a second XENYX or BEHRINGER ULTRALINK PRO MX882 can
be connected. Alternatively the line or tape output of a hi- amplier with source
selection switch could also be hooked up here, allowing you to easily listen to
additional sources (e.g. CD player, MP3 player, sound card etc.).
2-TRACK OUTPUT
These connections are laid out as RCA connectors and are wired parallel to
MAINOUT. Connect the inputs of a computer sound card or a recorder here.
Theoutput signal level is set up using the highly accurate MAIN MIX fader.
2.4 Main section
CLIP
SIG
Fig. 2.4: Control elements of the main section
+48 V
The red “+48 V” LED lights up when the phantom power is turned on.
Phantompower is required to operate condenser microphones and is activated
using the +48 V switch located above the +48VLED.
Connect microphones before you switch on the phantom power supply.
Please do not connect microphones to the mixer (or the stagebox/
wallbox) while the phantom power supply is switched on. In addition,
the monitor/PA loud speakers should be muted before you activate the
phantom power supply. After switching on, wait approx. one minute to
allow for system stabilization.
Caution! You must never use unbalanced XLR connectors
(PIN 1 and 3 connected) on the MIC input connectors if you want to
use the phantom power supply.
POWER
The POWER LED indicates that the console is powered on.
LEVEL INDICATOR
The 4-segment display accurately displays the relevant signal level.
7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

behringer-xenyx-qx1002usb

Suche zurücksetzen

  • Wie kann man den Hall-Effekt aus- und einschalten? Eingereicht am 14-2-2023 11:18

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Behringer Xenyx QX1002USB wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Behringer Xenyx QX1002USB

Behringer Xenyx QX1002USB Kurzanleitung - Deutsch, Englisch, Französisch, Portugiesisch, Spanisch - 17 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info