468359
25
Zoom out
Zoom in
Vorherige Seite
1/27
Nächste Seite
6. Additional Information
BenQ PE8700 User’s Manual
25
Troubleshooting
11. Put on the front
lamp cover.
12. Tighten the screws
on front lamp cover.
13. Turn the power on and go into Environment menu to
reset the "Lamp Timer" item.
Problem Cause Remedy
This projector does
not turn on.
There is no power from the power
cable.
Plug the power cord into the AC inlet on the
rear of the projector, and plug the power cord
into to the power outlet.
The power switch is not in the on
position.
Put the power switch in the on position.
Turn the projector on again during the
cooling process.
Wait this unit complete the cooling down
procedure.
Front lamp cover is not attached well. Correctly attach the front lamp cover.
No picture. The front lamp cover has not been
attached securely.
Correctly attach the front lamp cover.
The projector is not correctly
connected to the input source device.
Check the connection.
The input signal has not been correctly
selected.
Selects the correct input signal with the INPUT
key on the remote control unit.
The input signal has not been correctly
selected in the "INPUT SOURCE" item
in the DISPLAY menu.
Select the correct input signal.
POWER LED or LAMP LED flashing. Please contact your BenQ dealer for
assistance.
Image is unstable. The connection cables are not
connected to this unit.
Correctly connect the cables to the
appropriate terminals.
Picture is blurred. The projection lens is not correctly
focused.
Adjust the focus of projection lens with the
focus ring.
The projector and the screen are not
aligned properly.
Adjust the projection angle and direction as
well as the height of this unit if necessary.
Remote control does
not work correctly
The batteries are out of power. Replace both batteries with new ones.
LAMP LED flashes red. The front lamp cover is not correctly
attached.
Correctly attach the front lamp cover.
The cooling fan is not working
properly.
Please contact your BenQ dealer for
assistance.
The temperature inside the projector
is extremely high.
Check that the ventilation holes are not
blocked.
POWER LED flashed
orange and green
sequentially.
The lamp has exceeded its specified
usage time.
Replace the lamp with a new one.
The lamp has burned out. Replace the lamp with a new one.
25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für BenQ PE 8700 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info