Bedienungsanleitung Binatone BabySense 5 (Seite 2 von 2) (Englisch)

567791

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Breathing & Movement Monitor

Medically approved

User Guide

English

V.BS5(B).1.EN.7.13

• Batteries are not inserted

correctly or may be ﬂat.

• Check batteries are inserted in the Control Unit

observing the correct polarity.

• Control Unit requires 4 X AA 1.5V Alkaline batteries (not supplied).

• Batteries low. • Replace all 4 batteries.

• Sensor pad is out of order.

• Cable is connected to

monitor’s blocked socket.

• Connect one sensor pad lay the baby on the bed for 1 minute.

If the alarm does not activate, the sensor pad is in order. If the

alarm activates, disconnect and place the sensor pad aside.

• Connect the other sensor pad and repeat steps above.

• Do not connect any cables to the blocked socket (only to

“SENSOR” socket).

• The mattress is not

touching the sensor pads.

• Make sure that the mattress and the sensor pads

are touching.

• The mattress is raised

(there is an object near the

sensor pads).

• Make sure that there are no objects next to the sensor pads

• Placing two sensors next to

each other (or using one

sensor) when the baby is of

crawling age or using two

sensor pads far apart from

each other when baby is

young and is not crawling yet.

• Connect according to instructions.

• It is important to use only one sensor pad when the baby is young

and is not crawling yet.

• It is important to make sure that two sensor pads are used when the baby

is moving around.

• Make sure the sensors are placed underneath baby’s location in bed/crib.

• The mattress does not

enable transfer of baby

movements. (a rigid mattress,

a mattress with springs or a

mattress with air pockets).

• Place extra plywood under the sensor pad so that the

sensor pad and the mattress will be tightly pressed together.

• Performance test is not

correct.

• Do not conduct performance test by picking up the

baby out of bed and waiting for the alarm to sound.

Kindly conduct performance test according to guidance in page 3.

• Environmental inﬂuences

detected by the sensor

pads, such as wind, fan, air

conditioner, mobile,

vibrations.

• Perform a test which will detect the source of the movement

that the device detects. For example, sources of wind such as: air

conditioner, an open window or a fan; movements of a baby

mobile (which can vibrate even if it's not turned on) walking

around the bed area or an intercom placed near the bed with

intense transmission levels. Solutions: Eliminate sources of wind,

remove the mobile etc. After neutralising all environmental

inﬂuences, perform the test again. If even after neutralising all of

the environmental inﬂuences, the alarm does not go off within

20 seconds, perform the following:

1. In the back of the sensor pads (see illustration 1)

reduce the sensitivity level to position 2 (on both sensor pads) and

perform again the Performance Test. If the alarm sounds within 20

seconds, than keep this sensitivity level.

2. If the alarm does not go off in time, than reduce the sensitivity

level to position 1 and perform again the Performance Test. If the

alarm sounds within 20 seconds, than keep this sensitivity level.

3. If the alarm does not go off in time at this level, than it is

suggested using only one sensor pad with the sensitivity level

adjusted on position 1.

4. PAY ATTENTION: Should false alarms sound as a result of

reduced sensitivity, than increase the level of sensitivity and

perform the Performance Test.

Solution

Possible Cause

Symptom

Lights on Control

Unit don’t illuminate

when turned ON

Low battery voltage

warning (red light)

on the Control Unit

False alarm up to

1/2 minute from

activating

False alarm after 1/2

minute from

activating

Delayed alarms

while taking the

baby out of the bed

The alarm does

not go off within

20 seconds when

performing the

correct

performance test

Troubleshooting Guide

Made by Hisense Ltd.

ISO 9001:2008 and ISO 13485:2003 certiﬁed

23, Becker St. Rishon le Zion 7535929, Israel

www.hisense.co.il

European Authorized Representative

OBELIS s.a email@obelis.net

Boulevard Général Wahis 531030 Brussels, Belgium

Tel +(32) 2.732.59.54 Fax +(32) 2.732.60.03

Power consumption approx. 1mA.

Battery life approx. 6 months using alkaline batteries.

Alarm volume typically 85dB SPL at distance of

one meter.

Size of sensor pad is 216 mm.

Technical Speciﬁcations

Contents

• Control Unit

• Control Unit Holder

• Optional hanging hook

• 2 Sensor pads

• 2 Cable Ties

• User guide

Please note that the batteries are not supplied.

"Babysense" requires no special treatment beyond

replacing batteries when the battery indicator light

goes on. The sensor pads and control unit may be

wiped with a damp cloth.

Batteries should be removed and the device stored in

a dry shaded place when not in use.

For additional information, please visit our website :

Website: www.binatoneonline.com

Customer Care Helpline Tel. No.:

UK : 0845 345 9677

Republic of Ireland : 08187 62092

Caring for your babysense

DISPOSAL OF THE DEVICE (ENVIRONMENT)

At the end of the product lifecycle, you should not dispose of this product with normal household waste. Take this

product to a collection point for the recycling of electrical and electronic equipment. The symbol on the product,

user’s guide and/or box indicates this. Some of the product materials can be re-used if you take them to a recycling

point. By reusing some parts or raw materials from used products you make an important contribution to the

protection of the environment. Please contact your local authorities in case you need more information on the

collection points in your area. Dispose of the battery pack in an enviormentally-friendly manner according to your

local regulations.

Binatone BabySense 5 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info