Bedienungsanleitung Black Decker BDV012I (Seite 5 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

53615

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

ENGLISH

6. Battery status LEDs

7. ON/OFF switch

8. LED area light on/off switch

9. Reverse polarity indicator

10. LED area light

11. Mains charging adaptor

12. 12 Vdc vehicle adaptor

13. Heavy-duty copper clamps

14. Clamp holders

15. Inflator nozzle

Use

Charging the unit (fig. A)

This unit is shipped in a partially charged state.

X Charge the unit before first use using the mains

charging adaptor (11) for 48 hours.

Lead-acid batteries require routine maintenance to ensure a

full charge and a long battery life. All batteries lose energy

from self-discharge over time and more rapidly at higher

temperatures. When the unit is not in use, Black & Decker

recommend that the battery is charged at least every 60

days.

X Check the battery charge level by pressing the battery

status pushbutton (4). The LED charge status display

(6) will indicate the level of battery charge. When only

one red LED lights, charge the unit.

Note: Charging the battery after each use will prolong the

battery life; frequent heavy discharges between charges

and/or overcharging will reduce battery life.

The battery can be charged using the mains charging

adaptor (11) or the 12 Vdc vehicle adaptor (12).

Charging the unit with the mains charger (fig. A)

Make sure that the ON/OFF switch (7) and the LED area light

(10) are turned off while the unit is being charged.

As charging progresses, the red LEDs will light one by one.

X Charge the unit until the green FULL LED lights.

X Continue to charge for one to two more hours.

Note: The mains charger should not be connected for more

than 60 hours.

X When charging is complete, disconnect the mains

charging adaptor (11) and store it in a safe place.

Charging the unit with the 12 Vdc vehicle adaptor (fig. A)

Make sure that the ON/OFF switch (7) and the LED area light

(10) are turned off while the unit is being charged.

The 12 Vdc vehicle adaptor (12) does not provide a taper

charge.

Warning! While charging with the 12 Vdc vehicle adaptor

(12):

X Do not charge for more than 4 hours maximum.

X Do not leave unattended.

To charge the unit with the 12 Vdc vehicle adaptor (12):

X Insert one end of the 12 Vdc vehicle adaptor (12) into a

12 Vdc accessory outlet on the vehicle or boat.

X Insert the other end of the 12 Vdc vehicle adaptor (12)

into the 12 Vdc charging socket (3) on the front of the

unit.

X To check the charge status of the battery during dc

charging, disconnect the 12 Vdc vehicle adapter from

the accessory outlet and push the battery status

pushbutton. Observe the battery status LEDs. Do not

charge for more than 3 to 4 hours maximum.

X When charging is completed, remove the 12 Vdc

vehicle adaptor (12) and store it in a safe place.

Warning! You must remove the 12 Vdc vehicle adaptor from

the 12 Vdc accessory outlet on the vehicle before attempting

to drive the vehicle. Failure to do so could result in some

cases of the engine continuing to run even when the ignition

key is removed which could result in personal injury or

property damage.

Using the unit as a jump-starter (fig. A & B)

Warning! Make sure the vehicle is in neutral with the parking

brake applied.

X Turn off the vehicles ignition and all accessories before

making any connections.

X Make sure that the units ON/OFF switch (7) is turned

OFF.

X The following procedure is for a negative earth system

ie the negative battery terminal is connected to the

chassis.

X Connect the positive (+) red clamp to the vehicle's

positive battery terminal.

X Connect the negative (-) black clamp to the vehicle's

chassis or a solid, non-moving, metal vehicle

component or chassis part.

Note: If you connections are incorrectly made the unit will

beep continuously and the red Reverse Polarity Indicator (9)

will illuminate, even if the ON/OFF switch (7) is in the OFF

position. Rectify the connections immediatley.

Warning! Make sure that the cables are not in the path of

moving belts or the fan.

X Turn the unit's ON/OFF switch (7) to the ON position.

X Start the vehicle and crank the engine in 3 to 6 second

bursts.

If the engine doesn't start within 6 seconds let the unit's

internal battery cool for 3 minutes before making another

attempt.

X When the vehicle starts, turn the unit's ON/OFF switch

(7) to the OFF position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker BDV012I Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker BDV012I

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info