Bedienungsanleitung Black Decker BDV012I (Seite 6 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

53615

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

ENGLISH

X Leave the vehicle's engine running.

X Disconnect the (-) black clamp connected to the engine

or chassis first, followed by the (+) red clamp that is

connected to the battery positive (+) terminal.

X Carefully press the negative (black) jumper cable wire

into the storage channel starting at the end furthest from

the clamp.

X Clamp the negative (black) clamp onto the clamp holder

(14).

X Carefully press the positive (red) jumper cable wire into

the storage channel starting at the end furthest from the

clamp.

X Clamp the positive (red) clamp onto the clamp

holder(14).

X Charge the unit as soon as possible.

Using the inflator (fig. C)

Warning! When using the inflator:

X Do not direct the nozzle at animals or bystanders.

X Never leave the compressor unattended when running.

X Only use the adaptors supplied.

X Should the unit run over an extended period of time it

may overheat and cause the thermal trip to activate.

When this occurs switch the compressor off and allow to

cool for 30 minutes.

X Keep the compressor stored out of reach of small

children.

X The gauge is intended as a guide only. Tyre pressures

should be regularly checked with a certified gauge.

X Do not over inflate any object as this may cause a risk

of injury.

This inflator can be used to inflate car tyres and sports

equipment.

X Remove the inflator hose from the storage

compartment.

X If an adaptor is required, choose the correct adaptor

(18) for the product you are inflating and fit it into the

nozzle (15).

X Fit the nozzle (15) of the inflator or the adaptor (18), if

fitted, to the valve of the item to be inflated. Make sure

that the nozzle (15) is locked in place.

X Move the inflator switch (16) to the on position (I).

X Monitor the pressure gauge (17) until the required

pressure is reached.

X Move the inflator switch (16) to the off position (0).

X Remove the adaptor (18), if fitted, or the nozzle (15)

from the inflated item.

X Remove the adaptor (18), if fitted, and store it in a safe

place and return the hose to the storage compartment.

Using the 12 Vdc portable power supply (fig. A)

This portable power supply can be used with all 12 Vdc

accessories equipped with a male accessory outlet plug

rated up to 5 amps.

Warning! Do not attempt to use or charge the unit while the

12 Vdc accessory outlet (3) is in use.

X Lift the cover of the 12 Vdc accessory outlet (3).

X Insert the 12 Vdc plug from the appliance into the 12

Vdc accessory outlet (3) on the top of the unit.

Warning! Do not exceed a 5A load.

X Switch on the appliance and operate as usual.

X Periodically press the battery status pushbutton (4) to

check the status of the internal battery.

Warning! Make sure that the unit's ON/OFF switch (7) is in

the OFF position when using the unit's 12 Vdc accessory

outlet (3).

Warning! Do not operate appliances that draw more than 5

amps.

Warning! Never insert a cigarette lighter into the 12 Vdc

accessory outlet (3).

Using the LED area light (fig. A)

The LED area light (10) will operate up to 114 hours on a full

charge. The LED area light's operating life is 100,000 hours.

X Slide the LED area light on/off button (8) on the top

panel of the unit to turn the LED area light (10) on.

X Slide the LED area light on/off button (8) on the top

panel of the unit to turn the LED area light (10) off.

Make sure that the LED area light is turned off while the unit

is being charged or stored.

Maintenance

Your Black & Decker tool has been designed to operate over

a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regular cleaning.

Warning! Before performing any maintenance or cleaning

on the appliance, unplug the appliance.

X From time to time wipe the appliance with a damp cloth.

Do not use any abrasive or solvent-based cleaner. Do

not immerse the appliance in water.

Replacing the fuse in the vehicle dc power cord

X Remove the gold cap by turning it counter clockwise.

X Remove the rubber washer, centre pin and the spring.

X Remove the fuse.

X Fit a new fuse of the same type and size (8 A).

X Install the centre pin, spring and rubber washer.

X Install the gold cap by turning clockwise onto the plug.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker BDV012I Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker BDV012I

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info