Bedienungsanleitung Black Decker GA100 T2 (Seite 5 von 52) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

586385

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

• Locate the cable and cable protector into the

body correctly (see opposite, figure a). Then fit

the cable clamp over the outer sheath of the

cable and screw down until the screws are fully

home. Failure to do this may result in the cover

not fitting correctly to the connector body.

• Before replacing the cover of the ‘female’

connector make sure that the cable clamp is

holding the outer sheath of the cable firmly with

screws fully home and that the two leads are

correctly fixed at the terminal screws and are not

taut (see opposite, figure a).

• Place the cover onto the body assembly

ensuring that it seats flat, then retighten the

fixing screw into the nut until the cover is

securely held (see opposite, figure c).

• Finally check that the cable protector is secure

and that there are no gaps between the cover

and the connector body.

terminal screws

clamping washers

connector body fixing screw

6mm

cable

clamp cover

cable

protector

Fitting a new mains plug (UK only)

Fitting the ‘female’ connector

(UK only)

To remove the cover, unscrew the fixing screw until it

is free of the nut which is located in the hexagonal

recess on the underside of the connector.

Take care not to lose the nut if it falls out.

There is no need to completely remove the fixing

screw as it is intended to remain captive in the cover.

The cover can now be removed by applying

pressure as follows.

apply

pressure here

The extension cable contains two wires which are

colour coded for easy recognition; brown is for ‘Live’

(L) and blue is for ‘Neutral’ (N). The female connector

is marked ‘L’ for live and ‘N’ for neutral. These

markings are located inside the body near the

terminal screws (see opposite, figure a). With the

connector cover removed, lift out the cable protector

and proceed as follows:

• Pass the cable through from the narrow end of

the cable protector (see opposite, figure a).

• Prepare the cable ends to the specified strip

lengths (see opposite, figure b).

• Remove cable clamp (see opposite, figure a).

Take care of loose parts.

• To connect the extension cable to the connector

terminals, unscrew the terminal screws until the

clamp washers have lifted just enough to enter

the conductor between the raised washer and

the terminal (see below). Connect the brown

lead to ‘L’ and the blue lead to ‘N’. N.B. There is

no need to remove the terminal screws.

Connections are not to be made under the

screw heads.

terminal screw

clamp terminal

washer conductor position

to left of screw

ENGLISH

Fit a

BS1363A

approved

plug

Connect blue

to N (neutral)

Make sure that the

outer sheath of the

cable is held firmly

by the clamp

Fit the

recommended

fuse

Connect brown

to L (live)

240 volts AC only.

Never use a light

socket

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GA100 T2 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker GA100 T2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info