Bedienungsanleitung Blaupunkt Blue Magic XLb 300 A (Seite 5 von 44) (Alle Sprachen)

614204

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

XLb 250 A • XLb 300 A

Connection (see page 42)

1 Power-on indicator (Power/Protect)

2 Connection for cable remote control

3 Phase position

4 Automatic switch-on

5 Left loudspeaker input

6 Right loudspeaker input

7 Preampli er inputs

8 20 A fuse

9 + Battery

: Remote connection

; – Earth

< Bass boost

= Upper cut-o frequency

> Input sensitivity

Voltage supply

We recommend a minimum cross section of 6 mm

Route commercially available plus cables to the battery

and connect via fuse holder.

Use cable glands for holes with sharp edges.

Securely fasten commercially available minus cables to a

noise-free earth point (chassis screw, chassis metal) (not

to the minus pole of the battery).

Scrap the contact surfaces of the earth point until they

are bright and grease with graphite grease.

Connection

9 is connected to the positive pole of the

battery and connection ; to negative vehicle ground. The

control of the XLb should ideally be a two-channel control,

either via the preampli er outputs or the loudspeaker out-

puts of the car sound system. A control solely via the right or

left channel is also possible since the low-frequency portion

of the music is generally identical on both channels.

Integrated fuse

The fuse integrated in the ampli er protects the output stage

and the entire electrical system in case of a malfunction. If a

replacement fuse is used, never bridge fuses or replace them

with a type with higher current.

Audio inputs

You can select between 2 di erent audio inputs;

Cinch (RCA)

Hi level (loudspeaker connections)

Use only one of the audio inputs; otherwise, it may lead to

audio interferences.

The preampli er outputs are connected to the cinch (RCA)

sockets

7 of the subwoofer box via a shielded sound cable.

With control via the loudspeaker outputs, the input connec-

tions of pos.

5/6 are fed to the closest loudspeaker cables

(front or rear) on the left and right. They are separated and

connected to the input connections. The polarity of the

+ or – connections must be observed. Bridge output stages

(BTL) can also be connected directly without an additional

adapter.

–

Switching on/o

A special feature of the XLb is its automatic switch-on. It is

set via the AUTO TURN ON switch 4:

REM

Switching on/off via the car sound system. The remote

connection

: of the XLb must be connected with a

switchable 12-V power supply (e.g. switching output of

the car sound system).

DC OFFSET*

Switching on/off via the loudspeaker connections

5/6.

AUDIO*

Switching on/o via cinch connectors (RCA)

* The subwoofer box automatically switches on if a music

signal is received. If no music signal is received for more than

60 seconds, the XLb automatically switches o .

GAIN control

The GAIN control > is used to adjust the input sensitivity of

the power ampli er to the output voltage of your car sound

system preampli er output.

The adjustment range is from 0.2 V to 10 V.

If a car sound system of a third party manufacturer is con-

nected, the input sensitivity must be adjusted corresponding

to the manufacturer data.

The GAIN control can also be operated via the enclosed cable

remote control. For this purpose, the remote control must

be connected to the REMOTE

2 socket of the XLb. As long

as the remote control is connected, changes made with the

GAIN control of the subwoofer box have no e ect.

A few important explanations in this context:

By turning the control clockwise, the input sensitivity of the

ampli er and, therefore, also the volume increases. However,

this is not a volume control; no further ampli er output

can be achieved in the end position, even if it may sound

like that at the beginning. The system merely increases the

volume faster if the volume control of the car sound system

is turned up.

Bass boost

The BASS BOOST control < is used to adjust the bass re-

sponse of the ampli er.

The adjustment range is from 0 dB to +12 dB.

X-OVER frequency control

The X-OVER control = allows setting the desired entry

frequency.

Example:

At a setting of 150 Hz, the ampli er has a frequency range

of 25 Hz to 150 Hz.

Settings

The following control setting is recommended as basic

setting before putting the device into operation: Sensitiv-

ity (GAIN) Pos. > to minimum, PHASE Pos. 3 to 0°,  lter

(X-OVER) Pos. = to approx. 80 Hz. Switch on the device and

select a musical piece with distinctive bass playback.

–

BM_XLb250A_XLb300A_22LG.indd 5BM_XLb250A_XLb300A_22LG.indd 5 12.09.2012 13:05:33 Uhr12.09.2012 13:05:33 Uhr

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Blaupunkt Blue Magic XLb 300 A Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info