Bedienungsanleitung Bomann GSP 5707 (Seite 17 von 20) (Englisch)

552048

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

12/2011

Water Connection

The appliance is to be connected to the water mains using new hose sets and that old hose-sets

should not be reused.

The water pressure must be between 0.04 MPa and 1 MPa. Is the pressure lower or higher pls. con-

tact a technical specialist.

1. Pull the safety water hoses completely out from storage compartment located

at rear of dishwasher.

2. Tighter the screws of the safety hose tot he faucet with thread 3/4(inch).

3. Turn water fully on before starting the dishwasher.

About the Safety Supply Hose

The safety supply hose consists of the double walls. The hose's system guarantees its intervention by

blocking the flow of water in case of the supply hose breaking and when the air space between the

supply hose itself and the outer corrugated hose is full of water.

How to Disconnect the Safety Supply Hose

1. Turn off the water.

2. Unscrew the safety supply hose from the tap.

Cold Water Connection

ACHTUNG: The appliance is to be connected to the water mains using new hose sets and that

old hose-sets should not be reused.

Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure that it is fas-

tened tightly in place. If the water pipes are new or have not been used for an extended period of time,

let the water run to make sure that the water is clear. This precaution is needed to avoid the risk of the

water inlet to be blocked and damage the appliance.

Hot Water Connection

The water supply to the appliance can also be connected to the house hot water line (centralized sys-

tem, heating system), as long as it does not exceed a temperature of 60 C. In this case, the wash

cycle time will be shortened and the wash efficiency slightly reduced.

The connection must be made to the hot water line following the same procedures as those for the

connection to the cold water line.

WARNING: To avoid that water pressure remains in the inlet hose, please close the hydrant after

using.

Drain Hose Connection

Insert the drain hose into a drain pipe with a minimum diameter of

40 mm, or let it run into the sink, making sure to avoid bending or

crimping it. Use the special plastic hinge that comes with the ap-

pliance . The top of the hose must be at a height between 500

mm (min) and 1100 mm (max).

The free end of the hose must not be immersed in water to avoid

the back flow of it.

How to Drain Excess Water From Hoses

If the sink is 1100 mm higher from the floor, the excess water in hoses cannot be drained directly into

the sink. It will be necessary to drain excess water from hoses into a bowl or suitable container that is

held outside and lower than the sink.

Water Outlet

Connect the water drain hose. The drain hose must be correctly fitted to avoid water leaks.

Ensure that the water drain hose is not kinked or squashed.

Extension Hose

If you need a drain hose extension, make sure to use a similar drain hose.

It must be no longer than 4 meters; otherwise the cleaning effect of the dishwasher could be reduced.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bomann GSP 5707 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bomann GSP 5707

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info