697140
4
Zoom out
Zoom in
Vorherige Seite
1/12
Nächste Seite
EasyControl – 6720818479 (2017/10)
4
Installation
4.2 Determining the installation location
Install the controller on an internal wall in the reference room.
Ensure that there is sufficient clearance around the controller.
Fig. 3 Installation location for controller, clearance
Fig. 4 Installation location for controller, temperature
4.3 Fitting the plinth
This plinth can be fastened directly to the wall, for example at the
location of the previous controller.
Pull the mains plug of the heat source from the socket.
Connect the connecting lead (BUS connection of the heat source) to
the terminals on the plinth. The wires can be connected in any
sequence.
Fig. 5 Connecting the plinth
4.4 Connecting to the heat source
Fig. 6 Connecting the EasyControl adaptor
There are various possibilities for connection to a heat source:
Replacing an existing controller of the 100 to 400 series on the same
plinth. EasyControl is ready for operation.
•Bosch
1)
Heat source with a visible orange controller connection on
the underside: Connect the EasyControl at the orange terminal of the
orange connection for the controller.
•Bosch
1)
heat source without a visible connection for the controller.
The heat source must be opened by a recognized installer.
Heat sources, which use iRT, OpenTherm or On-Off, can only be
connected with an EasyControl adaptor (accessories), (see the back
of this document for the web address and select “Is EasyControl
suitable for me”), or consult a recognized installer.
A reference room is a room (for example the living room),
where the temperature, which is representative of the
whole dwelling, is measured, and where most time is
spent.
If weather-compensated control is used, it is not
necessary to locate the controller in the reference room.
When replacing a controller of the 100 to 400 series with
EasyControl, the existing plinth can continue to be used
( section 4.5).
When fitting to a recessed wall box, ensure that the room
temperature measurement can not be impaired by any
draughts. If required, stuff the recessed wall box with
thermal insulation material.
6720818478-2.1TD
1 m
1,2 - 1,9 m
0,75 m
0,6 m
6720818478-3.1TD
0,6 m
1 m
0,4 m
The installation instructions for the heat source contain
further information about the connection of EasyControl.
1) Or a Bosch Group brand (Nefit, Junkers, Worcester, ELM LeBlanc).
6720818478-4.1TD
EMS
l 100 m
EMS BUS
(15 V )
DC
6720818478-55.1TD
iRT
OpenTherm
On-Off
EasyControl
Adapter
l 100 m
l 3 m
4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bosch EasyControl CT200 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Bosch EasyControl CT200

Bosch EasyControl CT200 Bedienungsanleitung und Installationsanweisung - Deutsch - 13 seiten

Bosch EasyControl CT200 Bedienungsanleitung und Installationsanweisung - Holländisch - 13 seiten

Bosch EasyControl CT200 Bedienungsanleitung und Installationsanweisung - Französisch - 10 seiten

Bosch EasyControl CT200 Kurzanleitung - Alle Sprachen - 36 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info