Bedienungsanleitung Bosch EasyControl CT200 (Seite 5 von 12) (Englisch)

697140

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Commissioning

EasyControl – 6720818479 (2017/10)

4.5 Installing (deinstalling) the controller

Fig. 7 Installing (deinstalling) the controller

Installing

▶ Hook the EasyControl behind the plinth [1].

▶ Press the EasyControl with the underside against the plinth, until an

audible “click ”is heard [2].

The EasyControl is now locked.

Deinstalling

▶ Unlock the EasyControl by pressing the unlocking key [3].

▶ Slightly lift the underside of the EasyControl and remove it [4].

5 Commissioning

5.1 Powering up EasyControl

▶ Remove the protective film from the EasyControl.

▶ Plug the mains plug of the heat source into the socket.

▶ Switch on the gas floor-standing boiler.

This also causes the EasyControl to be supplied with mains voltage, and

it searches for a connection to:

• The heat source [1],

• A Wi-Fi network [2],

• The Bosch server [3].

Fig. 8 Start screen

[1] Connection with the heat source

[2] Connection with Wi-Fi network

[3] Connection with Bosch server

[4] Software version (example)

[5] Connection made (example)

[6] Connection not made (example)

A green check mark [5] shows, that the connection is made. A red cross

[6] shows, that the connection is not made. See  section 8.4, page 8

for an overview of possible causes and solutions.

5.2 Software update

The software version of this document is 01.xx.xx. The installed

software version is shown in the start screen [4]. Software updates are

performed automatically. It is possible that, when delivered, the

EasyControl does not yet have the current software version and does not

therefore support all the functions in the app. The update may take a few

days.

After an update has been performed, the arrangement of the touch

screen may differ from this document. See the latest version of this

document on the EasyControl site for Bosch.

5.3 Operation of the touch screen

It is possible to change the settings by means of a horizontal or vertical

wiping movement (swipe) or by pressing (tap). Only operate the touch

screen with your hand.

Fig. 9 Swipe or tap

5.4 Connecting with Wi-Fi network

After the EasyControl has been connected to the heat source, it

automatically searches for Wi-Fi networks [2] and displays these on the

touch screen. While the search is being performed, a flashing Wi-Fi

symbol appears on the touch screen.

Fig. 10 Available Wi-Fi networks

[1] Cancel key

[2] Available Wi-Fi networks

▶ Swipe vertically to find the Wi-Fi network.

▶ Select the desired Wi-Fi network by tapping.

If the Wi-Fi network is secured with a password:

▶ Enter the Wi-Fi network password ( section 5.5).

6720818478-5.1TD

6720818478-42.1TD

01.00.00

1) See the back of this document for the web address.

EasyControl can only make a connection to “visible”

networks. If EasyControl is to establish a connection with

a “hidden network”, this must first be made “visible”.

After a connection has been established, the network can

be “hidden” again.

6720818478-15.1TD

6720818478-43.1TD

Home 3

Network 8

Wifi 7

Wifi 8

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch EasyControl CT200 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch EasyControl CT200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info