3
5. Cut a citrus fruit in half and press the cut end of one fruit half onto the cone. T
the machine and choose the speed. Choose a low speed rotation and increase to a
higher rotation if necessary
excessively high speed rotation.
The cone will scrape the pulp out and squeeze the juice from the fruit.
6. T
times.
Rotating
Head
Screening
Plate
Motor
Shaft
Processing Using The Mixing Cup
1. Make sure that the Control Switch is turned to OFF (O) and that the unit is unplugged.
2. Put the sealing ring into the cutter seat slot and screw and fasten the mixing cup into the
cutter seat (clockwise to fasten and counter-clockwise to loosen). Put the mixing cup cover
and the feed cover on.
3. Screw the cutter seat clockwise into the main machine.
Note: When disassembling, (counterclockwise) do not hold and unscrew the cup only as then the
cup will unscrew from the cutter seat and the food in the cup will leak out. Hold the cup and cutter
seat together to disassemble.
MIXING FRUIT OR VEGET
Peel and shell fruit or vegetables and cut into cut into small blocks or sections. Put 600g into the
mixer at a time, pour in the appropriate amount of cool boiled water and mix for 1min on high
speed.
T
Mixing Cup
Mixing Cutter
Seat
Processing Using The Mincing Cup
1. Screw the mincing cup into the cutter seat (clockwise).
2. T
2 centimeter squares. Put 200g into the mincing cup at a time. Put the cup cover on the
mincing cup and mount it on the main machine according to the position shown in the
diagram. T
button switch on.
3. While mincing, add some edible oil or flavoring to the meat to produce better results.
Note: If the rotating speed slows down abruptly due to too much meat being processed at a time or
because tendons become entangled in the blade, turn the machine off and remove excess meat or
tendons.
Mincing Cup
Processing Using Grinding Cup
1. The grinding cup may be used to grind dried food into powder
2. T
tight in a clockwise direction. Mount on the main machine according to the position shown
in the diagram. T
grinding button switch on.
3. When grinding sesame, walnut and other oily food, add a spoon of granulated sugar into the
grinding cup for better results.
Note: If the cutter does not make contact with the food, switch off the power supply
softly and then turn on to grind again.
Grinding Cup
TROUBLESHOOTING GUIDE
Before calling the Customer Service Number
PROBLEM CAUSE/SOLUTION
Unit does not operate on any speed
or Pulse.
• Is the unit plugged in? Does the outlet work?
• Are the bowl, bowl lid and food chute lid all locked
into place? See page 4 “How to
Food is not chopped, sliced or
shredded uniformly
• Packing too much food in the food chute, or
pushing too hard on the food pusher may cause the
processed food to be irregularly sliced or shredded.
Unit stops and will not switch on
again.
• Are the bowl, bowl lid and food chute lid all locked
into place? They may have moved slightly during
processing. See page 4 “How to
• Is the power outlet still working? Check by plugging
in a working lamp or other appliance. Y
overloaded the circuit and blown a fuse or tripped
the circuit breaker
• Turn the unit OFF
and then turn back ON.
If none of these suggestions correct the problem, DO
NOT attempt to repair the unit. Call the customer service
number to get the name of your nearest Authorized
Service Centre.
Unit emits a burning smell • There may be some residue left on the motor from
the manufacturing process, causing a slight odour
during initial use. This will go away
odour or any visible smoke appears, unplug the unit
IMMEDIAAuthorized
Service Centre.
Motor seems weak • Are you using the recommended speed for the item
you are processing?
• Are you using the recommended food size and
quantity to be processed?
DO NOT OVERLOAD YOUR PROCESSOR
CLEANING, STORAGE
1. Wash bowl, lids, blade, discs, and removable drive sleeve and food pusher in hot, soapy water
Rinse and dry thoroughlyTo clean food
thoroughly from the bowl, lid and food chute immerse them in hot soapy water
NOTE: Do not store the unit with lid in locked position as this may put a strain on the interlock tab.
2. Wipe base, control panel and cord with a damp cloth or sponge. T
use a mild non-abrasive cleanser
3. T
shaft and the slicer/shredder disc on the chopping/mixing blade. The removable drive sleeve
may be stored in the bowl. Place the lid on the bowl but do not lock.
4. Place a drop of vegetable oil on each screw in the food chute once a month.
HOW TO RELEASE THE SUCTION CUP
The suction cup feet on the bottom of your Food Processor are designed to keep the unit stationary
during use.
T
by placing your hands under the unit (as illustrated) and lifting up one side.
be used. The electrical rating of the extension cord must be equal to or greater than the rating of
the appliance. Care must be taken to arrange the extension cord so that it will not drape over the
counter top or table top where it may be pulled by children, or accidentally tripped over
USING YOUR FOOD PROCESSOR
How T
Align the base and the bowl as illustrated. T
will lock onto the base in 3 different positions for user convenience.
NOTE: The food processor will not work unless the bowl is locked into position.
How T
Align the lid as illustrated, by placing a thumb on the lid tab and twisting the lid clockwise. Four
visual alignment markers are provided (see illustration), one on the bowl, one on the handle and
two on the bowl lid.
NOTE: The food processor will not work unless the lid is locked into position.
How T
The control dial is conveniently located on the front of the base.
Rotate the knob clockwise to increase speed. Rotate counter-clockwise to reduce speed. For
instant on and off control, use the PULSE (P) button by rotating the knob counter-clockwise. T
off the machine, rotate the switch to OFF (O).
Processing Tips
This food processor is excellent for chopping, mixing, slicing and shredding most foods. However
to maintain peak performance, do not use your food processor for: grinding grain, coffee beans or
spices; slicing frozen meat or crushing ice.
Operating time will depend on the quantity of food being processed. Most foods can be sliced,
chopped or shredded in seconds.
NOTE: If the unit is operated for 30 seconds continuously
before continuing.
Processing Using Chopping/Mixing Blade
For a more uniform consistency
example, should all be cut in 1-inch (2.5 cm) chunks. Do not process 4-inch (10cm) pieces with
1/2-
Motor Shaft
Slicer
Shredder
Disc
Removable
Drive Sleeve
The Chopping/Mixing Blade can be used to chop coarsely
smooth consistency
1. Make sure that the Control Switch is turned to the OFF (O) position and that the unit is
unplugged
2. Lock the bowl onto the base (See “How to Lock the Bowl” )
3. Place the Chopping/Mixing Blade onto the motor shaft of the food processor in the center of
the bowl. T
Caution: Handle carefully; the blade is sharp!
4. Lock the lid onto the bowl. Insert the food pusher into the food chute.
Do not puree or mash starchy vegetables like potatoes. They will be over-processed in a
second and turn gummy
5. Plug the unit into the power outlet and process the food. The processing speed and time
will determine the finished consistency of the food. Use the Pulse button to avoid over
processing.
6. When finished processing, select OFF (O) or release the PULSE button.
Caution: Wait until the blades have stopped rotating completely before removing the
lid.
7. Unplug the unit.
Chopping/Mixing Blade
Motor Shaft
Processing Using Slicer/Shredder
* T
Place cheese in the freezer for 30 minutes before processing.
* The Reversible Slicer/Shredder Disc has a slicing blade on one side and shredding teeth on
the other
1. Make sure that the Control Switch is turned to OFF (O) and that the unit is unplugged
2. Lock the bowl onto the base (See “How to Lock the Bowl”).
3. Put the Slicer/Shredder Disc on the Removable Drive Sleeve with the desired side facing up
for either slicing or shredding. Lock the lid onto the bowl (See “How to
the Lid”).
4. Insert the food pusher into the chute.
NEVER PUSH FOOD THROUGH THE CHUTE WITH
5. Plug in the unit.
6. Select the speed. While pressing on the food pusher
and shredding performance or press PULSE to process the food.
NOTE: The food chute lid is designed to pivot towards the right when processing food in order to fill
the entire food chute.
7. When the food chute is empty
Caution: Wait until the blade has stopped rotating completely before removing the lid. Unplug
the unit.
Slicer
Shredder
Disc
Motor Shaft
Processing Citrus Juice
1. Make sure that the Control Switch is turned to OFF (O) and that the unit is unplugged.
2. Lock the bowl onto the base.(See “How to Lock the Bowl”)
3. Put the Citrus Juicer Disc on the Removable Drive Sleeve (clockwise for fastening).
4. Fit the appropriate cone onto the drive shaft. (The large cone is suitable for juicing larger
citrus fruit, such as grapefruit, oranges etc. The small cone is suitable for juicing small citrus
fruit, such as lemons, limes etc.)
