Bedienungsanleitung Bresser 7007550 Meteo NBF Colour (Seite 20 von 24) (Deutsch, Englisch)

729945

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

20 / 24

1 Outdoor temperature value 2 Temperature unit (°C or °F selectable)

3 Indoor temperature value 4 Temperature unit (°C or °F selectable)

5 Temperature trend (rising or falling) 6 Battery level indicator (base station)

7 Symbol for highest (MAX) or lowest (MIN)

value (indoor)

8 Humidity trend (rising or falling)

9 Indoor humidity value 10 Atmospheric pressure (rising or falling)

11 Atmospheric pressure value 12 Symbol for highest (MAX) or lowest (MIN)

atmospheric pressure value

13 atmospheric pressure unit (inHg or hPa

selectable)

14 Atmospheric pressure history (12 hours)

15 Moon phases 16 Weekday

17 Month (M) 18 Day (D)

19 Alarm symbols 20 Current time (minutes)

21 Current time (hours) 22 AM/PM information in 12-hour time mode

23 Time zone (ZONE) 24 Symbol for radio signal

25 Daylight saving time (DST) 26 Snooze function enabled

27 Graphical weather trend display 28 Humidity value (outdoor)

29 Selected channel for remote sensor 30 Data reception symbol

31 Battery level indicator (remote sensor) 32 Symbol for highest (MAX) or lowest (MIN)

value (outdoor)

8 Before starting operation

NOTICE

Avoid connectivity disruptions!

To avoid connectivity disruptions between the devices, consider the following points before starting

operation.

1. Place base station (receiver) and remote sensor (sender) together as close as possible.

2. Set up power supply for the base station and wait until the indoor temperature is displayed.

3. Set up power supply for the remote sensor.

4. Position the base station and the remote sensor within the effective transmission range.

When changing batteries always change batteries in the main unit as well as all remote units and re-

place them in the correct order, so the remote connection can be re-established. If either of the

devices is mains-powered, the power supply must be disconnected for a short moment also for this

device when exchanging the batteries. If batteries are exchanged in only one of the devices (i.e. the

remote sensor) the signal can’t be received or can’t be received correctly.

Note, that the effective range is vastly affected by building materials and position of the main and re-

mote units. Due to external influences (various RC devices and other sources of interference), the

maximum distance can be greatly reduced. In such cases we suggest to position the main unit and the

remote sensor at other places. Sometimes all it takes is a relocation of one of these components of a

few inches! Though the remote unit is weather proof, it should be placed away from direct sunlight,

rain or snow.

9 Setting up power supply

Base device

1. Put the DC connector into the connection socket of the base station.

2. Put the mains plug into the power outlet.

3. The device is energized directly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bresser 7007550 Meteo NBF Colour Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bresser 7007550 Meteo NBF Colour

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info