Bedienungsanleitung Bresser 7007550 Meteo NBF Colour (Seite 21 von 24) (Deutsch, Englisch)

729945

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

21 / 24

4. Wait until the indoor temperature is displayed on the base station.

NOTICE!For permanent operation, mains power supply is recommended. Alternatively a

power supply with batteries is also possible. Proceed as follows:

5. Remove the battery compartment cover.

6. Insert the batteries into the battery compartment. Ensure that the battery polarity (+/-) is correct.

7. Replace the battery compartment cover.

8. Wait until the indoor temperature is displayed on the base station.

NOTICE!When switching from mains power supply to battery power supply or vice versa,

the power supply is being disabled for a short moment for technical reasons. In this process

all settings made previously, will be deleted.

Remote sensor

1. Remove the battery compartment cover.

2. Insert the batteries into the battery compartment. Ensure that the battery polarity (+/-) is correct.

3. Set the channel selector switch to the desired channel (1, 2 or 3).

NOTICE!This weather station can be operated with up to 3 remote sensors. Each remote

sensor being connected must be operated on a different channel. If only one remote sensor

is connected, it should be operated on channel 1.

4. Replace the battery compartment cover.

10 Automatic time setting

After the power supply was established, the clock will automatically search for the radio signal. This

will take approximately 3 to 8 minutes to finish this process.

If the radio signal is received correctly, the date and time will be set automatically and the radio control

signal icon turns on.

If the clock fails to receive the time signal, go ahead with the following steps:

1. Press and hold the DOWN button for approx. 2 seconds to re-initialize radio signal reception.

2. Is the device still not receiving the signal, the time must be set manually.

Read the detailed manual for more information about manual time and alarm time settings (see down-

load information on page 2).

11 Manual time setting and setiings for weather

information display

1. Press and hold MODE button for approx. 3 seconds to change to time setting mode.

2. Digits to be set are flashing.

3. Press UP or DOWN button to change the value.

4. Press MODE button to confirm and continue to the next setting.

5. Settings order: Year > Change day and month > Month > Day > Hours > Minutes > 12/24-hours

mode > Time zone > Language > Setting weather information display > Barometric pressure unit

hPa/inHG

6. Finally press the MODE button to save the settings and exit the setting mode.

12 Alarm setting

1. Press MODE button several times to select the desired alarm function: Alaram 1 (AL 1) or Alarm 2

(AL 2). The display switches to the preset alarm time.

2. Press and hold MODE button for approx. 3 seconds to enter the alarm time setting mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bresser 7007550 Meteo NBF Colour Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bresser 7007550 Meteo NBF Colour

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info