Bedienungsanleitung Bresser 7009970 Air Quality Sensor (Seite 1 von 6) (Deutsch, Englisch)

785371

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

EN INSTRUCTION MANUAL

About this Instruction Manual

These operating instructions are to be considered a component of the device.

Please read the safety instructions and the operating instructions carefully before use.

Keep these instructions for renewed use at a later date. When the device is sold or given to someone else,

the instruction manual must be provided to the new owner/user of the product.

GENERAL WARNINGS

• Risk of electric shock — This device contains electronic components that operate via a power

source (batteries). Children should only use the device under adult supervision. Only use the device

as described in the manual; otherwise, you run the risk of an electric shock.

• Choking hazard — Children should only use the device under adult supervision. Keep packaging

material, like plastic bags and rubber bands, out of the reach of children, as these materials pose a

choking hazard.

• Risk of chemical burn — Keep batteries out of the reach of children! Make sure you insert the bat-

teries correctly. Leaking battery acid can lead to chemical burns. Avoid contact of battery acid with

skin, eyes and mucous membranes. In the event of contact, rinse the aected region immediately

with a plenty of water and seek medical attention.

• Risk of re/explosion — Do not expose the device to high temperatures. Use only the recom-

mended batteries. Do not short-circuit the device or batteries, or throw them into a re. Excessive

heat or improper handling could trigger a short-circuit, a re, or an explosion.

• Do not disassemble the device. In the event of a defect, please contact your dealer. The dealer will

contact the Service Centre and can send the device in to be repaired, if necessary.

• Use only the recommended batteries. Always replace weak or empty batteries with a new, complete

set of batteries at full capacity. Do not use batteries from dierent brands or with dierent capaci-

ties. The batteries should be removed from the unit if it has not been used for a long time.

SCOPE OF DELIVERY

Sensor, Operating instructions, 3x AA batteries.

BEFORE YOU BEGIN

• We recommend using alkaline batteries. If temperatures regularly fall below 0°C (32°F), we recom-

mend using lithium batteries.

• Avoid using rechargeable batteries. (Rechargeable batteries cannot maintain correct power

requirements.)

• Insert batteries before rst use, matching the polarity in the battery compartment.

3x AA batteries are required.

EC Declaration of Conformity

Hereby, Bresser GmbH declares that the equipment type with part number: 7009970 is in

compliance with Directive: 2014/53/EU. The full text of the EU declaration of conformity is

available at the following internet address:

www.bresser.de/download/7009970/CE/7009970_CE.pdf

UKCA DECLARATION OF CONFORMITY

Bresser UK Ltd. has issued a „Declaration of Conformity“ in accordance with applicable

guidelines and corresponding standards. The full text of the UKCA declaration of

conformity is available at the following internet address:

www.bresser.de/download/7009970/UKCA/7009970_UKCA.pdf

Bresser UK Ltd. • Suite 3G, Eden House, Enterprise Way, Edenbridge, Kent TN8 6HF, Great Britain

NOTES ON CLEANING

• Remove the batteries before cleaning.

• Only use a dry cloth to clean the exterior of the device. To avoid damaging the electronics, do not

use any cleaning uid.

• Protect the device from dust and moisture.

OVERVIEW

1. LCD display

2. [MODE] key

3. [CHECK] key

4. Wall mounting holder

5. [CH1~4] slide switch

6. [RESET] key

7. Battery compartment

8. DC adapter USB power port

BATTERY INSERTION

1. Unscrew and remove the battery door of

sensor with a screwdriver

2. Insert the 3 rechargeable batteries (included) into the battery compart-

ment in the following order:

x 3

3. Screw the battery door compartment on tightly.

4. After inserting batteries, all LCD segment will be shown for 1 second.

Note:

- Please prepare a screwdriver for removing and close the battery door.

GETTING STARTED

1. Slide [CHANNEL] to set the channel number

for your sensor(s).

2. Use a pin to press [RESET] key for run the

channel number.

Note:

- Iftherearemorethanonesensorinuse,ensuretoassigndierentchannelnumbersfor

each sensor to enable the measurement to displayed correctly on the console (purchase

of separately).

LCD DISPLAY

1. PM2.5/PM10 display mode

2. PM2.5 / PM10 concentration value

3. PM2.5 / PM10 concentration level

4. Sensor Wireless channel number

5. Transmission signal

6. Battery power indicator

DISPLAY MODE

Press [MODE] to toggle the display mode between PM10 and PM2.5.

Art.No.: 7009970

Air Quality Sensor

EN INSTRUCTION MANUAL

DE BEDIENUNGSANLEITUNG

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bresser 7009970 Air Quality Sensor Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info