697447
70
Zoom out
Zoom in
Vorherige Seite
1/72
Nächste Seite
5
Operating and fault displays
MCM10
70
5.4 Operating and fault indications via the RC35
The operating and fault indications relating to all boilers
and the MCM10 module can be checked on the controller
with EMS BUS control. For an explanation of the displays
on the MCM10 module, see tab. 11. The meaning of all
other displays is given in the documentation of the
controller and boilers.
5, 6,
7, 8
Operation: no heat
demand to the boiler;
boiler operational.
Operation: heat
demand to the boiler;
boiler in operation.
Configuration:
communication
between this boiler
and MCM10 module.
Wait until the
configuration has
completed.
Operation: no boiler
connected.
Fault: boiler fault.
1)
Remove fault on the
boiler.
Configuration/
Fault: no
communication
between
MCM10 module and
this boiler, although it
is installed.
Check the
corresponding
connecting lead/
cable.
Remove boiler fault.
Replace
MCM10 module.
Fault: no
communication
between
MCM10 module and
boiler because it has
been deliberately
removed.
Carry out
configuration reset
(Æ chapter 4.3).
Fault: communication
error between
MCM10 module and
boiler.
1)
Check the
corresponding
connecting lead/
cable.
Replace
MCM10 module.
1) Another boiler will be enabled automatically in case of heat demand
LED Off On Flashing
No. Diagnosis Remedy Diagnosis Remedy Diagnosis Remedy
Tab. 10 Operating and fault displays
Display Description Remedy
5H Break in BUS communication. Display in case of less than 4 installed boilers.
Check the cable between the boiler and the MCM10 module for a possible break.
Check the cable for firm seating and contact.
Check whether this fault originates in a boiler (Æ boiler installation instructions).
Replace MCM10 module.
4U
4Y
Short circuit (4U) or contact break
(4Y).
Check flow temperature sensor and its lead.
Replace MCM10 module.
EF Internal electronics fault. If a fault is indicated by one of the boilers: replace burner control unit of the corresponding
boiler.
If the fault is not indicated by one of the boilers: replace MCM10 module.
8Y The external switching contact has
opened.
Check the cable of the external switching contact for a possible break.
Check whether the connecting plug is present.
Replace MCM10 module.
AE Jumper configuration fault. Check whether the jumper has been correctly set.
AU The calculated boiler water
temperature is not reached in time.
Check whether a sufficient number of boilers functions normally.
AY A fault has occurred on one or
several boilers.
Remedy the fault on the boiler concerned.
Tab. 11 Operating and fault indications via the RC35
70

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Buderus MCM10 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info