Bedienungsanleitung Caliber CA 2000B (Seite 2 von 13) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch)

497403

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

ENGLISH

RCA INPUT

• Connect the RCA-outputs of your radio to the RCA input terminals of the amplifier.Take good care

that you connect the Right output of your radio to a Right input of your amplifier,and that you con-

nect the Left output of your radio to a Left input of your amplifier.

AMPLIFIER ADJUSTMENTS

• Put the input level adjustment knob to the minimum.

• Put the volume of your radio to 3/4 of the maximum.

• Adjust the Bass Boost to your personal sound.

•Now adjust the input level of the front channel. Slowly turn up the input level and listen carefully

untill you hear the amplifier begin to distort.A Caliber Amplifier “clips” very softly, so this can some-

times be a difficult adjustment. If you have turned up the Bass Boost to much, the amplifier will start

clipping immediatly. In that case you must turn back the Bass Boost and start adjusting the inputle-

vel again.You will hear that the Bass you wanted can be required in this way.

CALIBER WARRANTY

Due to the complexity of our products, we strongly recommend that this amplifier is installed by

your authorized Caliber dealer. If properly installed by your dealer we provide a warranty for 12

months from the date of purchase.

If you install this amplifier yourself, we wish you lots of fun and succes in doing so. If you follow our

guidelines, you’ll get the best result. Our warranty, however, will be limited to and not exceed 30

days from the date of purchase.

FEATURES

• Mono output.

• Pulse Width Modulated (PWM) MOSFET Power Supply.

•Variable input sensitivity: RCA input 0.2V to 3V.

• Thermal-, Overload- and Shortcircuit protection.

• Excellent muting circuitry assures no turn on/off ‘pops’.

• Built-in Full Range / Low Pass Filter Switch.

• Chrome plated power connectors for optimal power distribution.

• European design and engineering.

• Chrome plated speaker connectors for optimal signal output.

MOUNTING

The amplifier has to have at least 5 cm (2”) ventilation space at all sides, to allow the heat to rise

away from the amplifier. Be sure that the power and signal cables can enter and leave the amplifier

in a straight line, to avoid the risk of malfunction. Always place the power- and signalcables at

opposite sides of the vehicle to reduce any noises.

The amplifier should be protected from exposure to moisture and direct sunlight.

Mark the mounting surface using the amplifier as a template, then drill 2.5 mm (1/8”) diameter holes

at the marked locations and mount the amplifier using the supplied self-tapping screws.

INSTALLATION

Remember to always disconnect battery ground before working on a vehicle’s electrical system!

Always place a fuse or circuit breaker no more than 30 cm (12”) from the battery, no greater than

the fuse(s) of your amplifier for optimal protection.

GETTING YOUR POWER STARTED

• First, the +12V terminal is connected directly to the battery of your car. Use a cable of at least

10 mm

, and make sure that the connectors are of the same value.

- Don’t forget the extra “Vehicle protection” fuse.

- The 12V + terminal should NOT be connected to the car fuse box.

• Second, the ground terminal (GND) must be fastened securely to the chassis of the vehicle with the

same mm

cable as the positive cable (the same amount of power has to run through it). Ensure

that all paint, undercoating or any other insulation is removed from the area where you want to

make your ground connection to.

•Third, the last cable to connect is your remote turn-on (REM). Many radio-cassette and CD-players

have an output terminal for connection of the REM of an amplifier. If you don’t have such an out-

put, a separate switch must be installed to control your amplifiers on/off function.

CA 2000B_Manual.qxd 27-02-2008 12:12 Pagina 2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Caliber CA 2000B Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info