Bedienungsanleitung Caliber RMD801DAB-BT (Seite 5 von 24) (Englisch)

699206

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

MANUAL RMD 801DAB-BT

Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive tape around them where they lie against

metal parts. To avoid short-circuiting, cover all disconnected lead with insulating tape. There is a possibility of short-circuiting if the

leads are not insulated.

Route and secure all wiring so it cannot touch any moving parts, such as the gear lever and handbrake. Do not route wiring in places

that get hot, such as near the heater outlet. If the insulation of the wiring melts or gets torn, there is a danger of the wiring short

circuiting to the vehicle’s body.

Don’t pass the yellow lead through a hole into the engine compartment to connect to the battery. This will damage the lead’s insula-

tion and cause a very dangerous short.

Do not shorten any leads, if you do, the protection circuit may fail to work when it should.

Never feed power to other equipment by cutting the insulation of the power supply lead of the unit and tapping into the lead. The

current capacity of the lead will be exceeded, causing overheating.

Since a unique audio I/C circuit is employed, never wire so the speaker leads are directly grounded or the left and right - speaker

leads are common.

When this product’s source is switched ON, a control signal is outputted through the orange lead. Connect to an external power amp’s

system remote control or the car’s Auto-antenna relay control terminal (max. 300mA 12V DC). If the car features a glass antenna,

connect to the antenna booster power supply terminal.

When an external power amp is being used with this system, do not connect the orange lead to the amp’s power terminal. Such con-

nection could cause excessive current drain and a major malfunction. Refer to the relevant owner’s manual for details on connecting

the power amp and other units, then make the connections correctly.

Do not block any vents or heater panels, Blocking them will cause heat to build up and may result in fire.

Make sure that the unit has a good chassis ground. A good ground connection will eliminate most electrical noise. A good chassis

ground requires a tight connection to the vehicles metal chassis. The area around the ground connection should be clean, bare metal

without rust, paint, plastic or dirt for a good electrical connection.

If noise is still experienced when the motor of the vehicle accelerates, a choke should be placed in line with the power to the unit.

The installation company will know what is required.

When replacing the fuse(s) the replacement must be of the same amperage as shown on the fuse holder. Never replace a fuse with

another of a different value. If the fuse blows again please contact your instsallation company.

Double check that all wiring and connections are correct before re-connecting the battery and turning on the unit.

After completing the installation and before operating the unit, reconnect the battery, then press the (RES) button with a pointed object,

such as a ball-point pen to set to unit to it’s initial status. After pushing the button, wait a few seconds for the red light to flash.

SAFETY PRECAUTIONS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Caliber RMD801DAB-BT Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Caliber RMD801DAB-BT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info