Bedienungsanleitung Cambridge Audio Azur 540 R (Seite 10 von 12) (Englisch)

497437

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

540R AV receiver

azur 540R AV receiver 11

These functions allow you to fine tune the audio output from the 540R

to get the perfect balance between your home cinema system and your

room.

Delay T

ime

To get the full benefit from your home cinema system it is often

desirable to have output from your surround, rear or centre speakers

delayed, creating a more realistic feeling of space.

Press the SPK Setup button on the remote handset. The

corresponding speaker appears on the display. i.e .C (centre), S

(surround), L/R (front left and right) or BS (back surround)

Press the Delay button to set the time delay and the use the +/-

buttons to adjust.

Delay t

ime s

etting a

djustable r

ange

Dolby®Digital mode: 0-15 ms in 5 ms step (S-Delay)

0-5 ms in 1 ms step (C-Delay)

Dolby Pro Logic®II Mode: 15-30 ms in 1 ms step (S-Delay)

Test T

one - L

oudspeaker l

evel a

djustment

The test tone function is useful to adjust the relative volume between

speakers in Dolby®Digital or Dolby®Pro Logic II modes.

Adjust the master volume to the normal listening level (half of max.

volume is recommended)

Press the Test Tone button on the remote handset.

A test tone will be emitted from each speaker each time you press

Test Tone button, looping in the following order:

L(front left)

R(front right)

LS (surround left)

RS (surround right)

C(centre)

SUB (subwoofer)

BS (surround back)

Adjust the level of each speaker using the Volume button.

The level of each speaker can be adjusted in 1 dB step from -10dB

to +10dB. Try to ensure that the volume of the tone is the same

from every speaker.

When the setting is finished, press the Test Tone button to stop the

test tone.

FINE TUNING SOUND

Channel S

elect - L

oudspeaker l

evel a

djustment f

or 6

Direct a

udio

The channel select button can be used to balance volume between

speakers in 6.1 channel mode when using the 6.1 analogue inputs.

As the Dolby®Digital signal is decoded in the external source,

sometimes, you may have to balance volume between speakers due to

the location of speakers. In this case:

Press the CH Select button on the remote handset and proceed as

per Test Tone instructions.

Low F

requency E

ffect (

(

LFE m

ix)

Use this function to fine tune the level of bass outputted by the 540R.

Press the LFE Trim button on the remote handset.

Use the volume keys to adjust between 0dB and -10dB

Note that the LFE function will automatically cancel if the volume button

is not pressed for 5 seconds.

Dynamic R

ange C

ontrol

By reducing the Dynamic range of the 540R output can be listened to at

a higher volume without bursts of noise. This is useful for watching

movies late at night, for example

Press the Dynamic button on remote control repeatedly until the

desired compression range is reached.

DRC=0/4 No Compression

DRC=1/4

DRC=2/4

DRC=3/4

DRC=4/4 Greatest Compression

Dynamic range compression is not possible with DTS®sources.

Note that the Dynamic Range Control function will automatically cancel

if the volume button is not pressed for 5 seconds.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cambridge Audio Azur 540 R Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cambridge Audio Azur 540 R

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info