Bedienungsanleitung Casio 5325 (Seite 1 von 9) (Englisch)

624831

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

Operation Guide 5325

E-4

To start HS1 high-speed movement

While the crown is pulled out, rotate it rapidly three turns away from you (for

forward movement) or towards you (for reverse movement). High-speed

movement will continue even if you release the crown.

To start HS2 high-speed movement

While HS1 high-speed movement is progress, again rotate the crown rapidly three

turns in the same direction as the current HS1 movement (away from you for

forward movement or towards you for reverse movement).

To stop high-speed movement

Rotate the crown in the direction that is opposite that of the current high-speed

movement or press any button.

Note

 If you do not perform any operation for more than two minutes after pulling out the crown, crown

operations will become disabled automatically. If this happens, push the crown back in and then pull it

out again to re-enable crown operations.

 You can use high-speed hand movement when conﬁ guring time settings in the Timekeeping Mode,

Alarm Mode, or Countdown Timer Mode.

 Button operations become disabled after you perform a crown operation. If this happens, rotate the

crown slightly. This should restore button operations.

MA1302-EA

E-1

ENGLISH

Congratulations upon your selection of this CASIO watch.

 Note that the product illustrations in this manual are intended for reference only, and so the actual product

may appear somewhat different than depicted by an illustration.

This watch does not have a city code that corresponds to the UTC offset of –3.5 hours. Because of

this, the radio-controlled atomic timekeeping function will not display the correct time for Newfoundland,

Canada.

Warning!

 The measurement functions built into this watch are not intended for taking measurements that

require professional or industrial precision. Values produced by this watch should be considered as

reasonable representations only.

 To ensure correct direction readings by this watch, be sure to perform bidirectional calibration before

using it. The watch may produce incorrect direction readings if you do not perform bidirectional

calibration. For more information, see “To perform bidirectional calibration” (page E-37).

 Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage or loss suffered

by you or any third party arising through the use of this product or its malfunction.

E-2

About This Manual

Operations are performed using the watch’s crown, and the three buttons

indicated by the letters A, B and C in this manual.

Hands and Indicators

z Hour Hand

x Second Hand

c Minute Hand

v Upper Dial Hand: Indicates a time, in 24-hour format, depending on the

current mode.

b Lower Dial Hand: Indicates the current mode.

n Day Indicator

This User’s Guide uses numbers shown above to identify watch hands and

indicator.



@>B

E-3

Using the Crown

The crown of this watch is a screw in lock crown. Before using the crown, you

must ﬁ rst rotate it towards you to loosen it.

Important!

 To maintain water resistance and avoid impact damage to the crown, be sure

to screw it back in when you are not using it.

The illustrations below show the different crown operations.

Pull out Rotate Push in

High-speed Movement

When rotating the crown to move the hands of the watch, you can use the operations described below

to move the hands at high speed, either forward or back. There are two high-speed levels: HS1 and HS2

(faster than HS1).

Crown

Loosen

E-5

Things to check before using the watch

1. Hold down C at least two seconds to enter the Timekeeping Mode, and then observe the

movement of the x

Second Hand.

Is the x Second Hand moving smoothly at one-second intervals?

Is the x Second Hand moving at two-second

intervals or is it stopped completely?

Go to step 2.

The watch is charged. For details about

charging, see “Charging the Watch” (page E-10).

Power is low. Charge the watch by placing it in a

location where it is exposed to light. For details,

see “Charging the Watch” (page E-10).

YES

2. Check the Home City.

Use the procedure under “To conﬁ gure Home City settings” (page E-25) to conﬁ gure your Home City.

Important!

 Proper time calibration signal reception depends on correct Home City, time, and day settings in the

Timekeeping Mode. Make sure you conﬁ gure these settings correctly.

E-6

3. Set the current time.

 To set the time using a time calibration signal

See “To get ready for a receive operation” (page E-17).

 To set the time manually

See “Conﬁ guring Current Time and Day Settings Manually” (page E-28).

The watch is now ready for use.

 For details about the watch’s radio controlled timekeeping feature, see “Radio Controlled Atomic

Timekeeping” (page E-15).

E-7

Contents

E-2 About This Manual

E-3 Using the Crown

E-5 Things to check before using the watch

E-10 Charging the Watch

E-11 To check the current power level

E-14 To recover from the sleep state

E-15 Radio Controlled Atomic Timekeeping

E-17 To get ready for a receive operation

E-19 To perform manual receive

E-20 To check the result of the latest receive operation

E-20 To turn auto receive on and off

E-22 Mode Reference Guide

E-23 To determine the watch’s current mode

E-23 To return to the Timekeeping Mode from any other mode

E-23 To select a mode

E-24 Timekeeping

E-25 Conﬁ guring Home City Settings

E-25 To conﬁ gure Home City settings

E-27 To switch between standard time and summer time manually

Casio 5325 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio 5325

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info