Bedienungsanleitung Casio 5394 - OCW-P1000 (Seite 1 von 9) (Englisch)

624833

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

Operation Guide 5394 (OC)

E-7

2. Check the Home City.

Use the procedure under “To conﬁ gure Home City settings” (page E-27) to conﬁ gure your Home City.

Important!

x Proper time calibration signal reception depends on correct Home City, time, and day settings in the

Timekeeping Mode. Make sure you conﬁ gure these settings correctly.

3. Set the current time.

x To set the time using a time calibration signal

See “To get ready for a receive operation” (page E-18).

x To set the time manually

See “Conﬁ guring Current Time and Day Settings Manually” (page E-30).

The watch is now ready for use.

x For details about the watch’s radio controlled timekeeping feature, see “Radio Controlled Atomic

Timekeeping” (page E-16).

E-6

Things to check before using the watch

1. Hold down

at least two seconds to enter the Timekeeping Mode, and then observe the

movement of the

Second Hand.

Is the

Second Hand moving smoothly at one-second intervals?

Is the

Second Hand moving at two-second intervals

or is it stopped completely?

Go to step 2.

The watch is charged. For details about

charging, see “Charging the Watch”

(page E-11).

Power is low. Charge the watch by placing it in a

location where it is exposed to light. For details, see

“Charging the Watch” (page E-11).

YES

E-5

To start HS1 high-speed movement

While the crown is pulled out, rotate it rapidly away from you (forward) or towards

you (reverse) until the desired HS1 high-speed movement starts.

To start HS2 high-speed movement

While HS1 high-speed movement is in progress, again rotate the crown rapidly,

away from you (forward) or towards you (reverse) in the same direction as the

HS1 movement until HS2 high-speed movement starts.

To stop high-speed movement

Rotate the crown in the direction that is opposite that of the current high-speed

movement or press any button.

Note

x You can use high-speed hand movement when conﬁ guring time settings in the Timekeeping Mode,

Alarm Mode, or Countdown Timer Mode, and when adjusting day indicator alignment.

E-4

Using the Crown

Pull out the crown before rotating it.

To pull out, rotate, or push the crown in

Pull out Rotate Push in

Note

x If you do not perform any operation for more than two minutes after pulling out the crown, crown

operations will become disabled automatically. If this happens, push the crown back in and then pull it

out again to re-enable crown operations.

x Button operations may become disabled after you perform a crown operation. If this happens, rotate

the crown slightly. This should restore button operations.

High-speed Movement

When rotating the crown to move the hands of the watch, you can use the operations described below

to move the hands at high speed, either forward or back. There are two high-speed levels: HS1 and HS2

(faster than HS1).

E-3

About This Manual

Operations are performed using the watch’s crown, and the three buttons

indicated by the letters A, B and C in this manual.

Hands and Indicators

Hour Hand

Second Hand

Minute Hand

Upper Dial Hand: Indicates a time, in 24-hour format, depending on the

current mode.

Lower Dial Hand: Indicates the current mode.

Day Indicator

This User’s Guide uses numbers shown above to identify watch hands and

indicator.



 







E-2

Applications

This watch has built-in sensors that measure direction.

Measurement results are indicated by the watch’s hands and displays. This feature makes this watch

useful when hiking, mountain climbing, or when engaging in other such outdoor activities.

Warning!

x The measurement functions built into this watch are not intended for taking measurements that

require professional or industrial precision. Values produced by this watch should be considered as

reasonable representations only.

x When engaging in mountain climbing or other activities in which losing your way can create a

dangerous or life-threatening situation, always use a second compass to conﬁ rm direction readings.

x Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage or loss suffered

by you or any third party arising through the use of this product or its malfunction.

Important!

x Whenever you use the digital compass of this watch for serious trekking, mountain climbing, or

other activities, always be sure to take along another compass to conﬁ rm readings. If the readings

produced by the digital compass of this watch are different from those of the other compass, perform

bidirectional calibration of the digital compass to ensure more accurate readings.

x Direction readings and digital compass calibration will not be possible if the watch is in the vicinity of

a permanent magnet (magnetic accessory, etc.), metal objects, high-voltage wires, aerial wires, or

electrical household appliances (TV, computer, cellphone, etc.)

E-1

ENGLISH

Congratulations upon your selection of this CASIO watch.

x Note that the product illustrations in this manual are intended for reference only, and so the actual product

may appear somewhat different than depicted by an illustration.

This watch does not have a city code that corresponds to the UTC offset of –3.5 hours. Because of

this, the radio-controlled atomic timekeeping function will not display the correct time for Newfoundland,

Canada.

Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage or loss suffered by

you or any third party arising through the use of your watch or its malfunction.

MA1410-EA

Casio 5394 - OCW-P1000 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info