Bedienungsanleitung Celestron 47005 (Seite 2 von 15) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

791750

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

If the battery power becomes low on the Sensor, a “low battery icon” will appear on the LCD display

and change batteries to ensure a strong signal is being sent to the Receiver.

Settings and Operation of the Receiver

y Indoor & Outdoor Temperature & Humidity – the indoor

temperature and humidity is shown on the LCD display as is the

outdoor temperature and humidity. The outdoor temperature and

humidity trends will be displayed with a small icon to the right of

each display.

y Data displayed in “C” or “F” – push the “- c/f” button (rear of

Receiver) when in a normal mode to change from “C” (Centigrade) or

“F” (Fahrenheit).

y Clock & Calendar – Press the “set” button and hold down for a

couple of seconds to enter the setup mode. Use the “+” or “-” buttons

to make changes. Press “set” after each setting is correct. The settings in

sequence will be: year / month / date / hour / minute /12-24hr format /

time zone / exit. The day of the week is indicated near the time.

y Time Zone – You can set an alternate time zone (during setup) for ±

12 hours. Once set you can access the alternate time by pressing for a

few seconds “- zone” button and doing the same to return to your

home time.

y Moon Phase – will automatically be seen on the display and will be

correct if the calendar is set to the actual.

y Max/Min Memory – in normal mode, press the button “min/max” to

see the maximum temperature and humidity both indoors and out,

press the button again to see the minimum temperature and humidity

both indoors and out, press the button again to return to the normal mode. The memory is

cleared once per day.

y Barometer & Weather Forecast – the weather station has a built-in barometer to measure

atmospheric pressure and forecasts the weather with icons for Sunny/Partly

Cloudy/Cloudy/Rainy/Stormy. The unit predicts the weather conditions for

the next 12 to 24 hours based on the atmospheric pressure change and is

about 70% correct. The company accepts no liability for any incorrect

forecast. In normal mode press and hold down the “baro/down” button on

the back of the Receiver for a few seconds so you can set how you want to

view the atmospheric pressure readings – “in/Hg” or “mb/hPa” (hold the

button down again for a few seconds to change the setting). For the

barometer to be as accurate as possible the altitude must be set for your

location and you can find out your altitude from various local sources. Press

and hold the “baro/up” button down to select and then toggle between feet

and meters. To confirm feet or meters press the “hist” button. Then, press

the “baro/up” or “baro/down” buttons to set the altitude for your location.

The pressure tendency is shown in a small icon above the forecast –

rising/steady/falling.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Celestron 47005 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info