Bedienungsanleitung Celestron 47005 (Seite 3 von 15) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

791750

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

The pressure history bar displays the moving atmospheric pressure history of the past 12 hours

which allows for forecasting. To view air pressure history for the past 12 hours, press the “hist”

button to select and view how many hours (repeatedly press the “hist” button).

The respective values can only be available after the barometer recorded the pressure date in the

past 12 hours. The spectrum bar chart indicates pressure changes of the past 1, 2, 3, 6, and 12

hours and is shown for a range of -0.24 to +0.24 in/Hg and -8 to +8 mb/hPa.

y Temperature & Humidity Alert – press the “alert” button on the rear of the Receiver to turn

the alert on or off. Press and hold the “alert” button to enter the setup mode. The indoor and

outdoor temperature and humidity upper and lower limits can be set by using the “+” and “-”

buttons and pressing “alert” to confirm each setting. When either the temperature or humidity

alert values have been reached while the alert is activated, the respective values will flash and

the alarm will sound --press “alert” to stop the alarm.

y Alarm Setting – Press the “alarm” button to toggle between alarm 1 and alarm 2, and normal

time. In “alarm 1” or “alarm 2” press and hold to set the alarm time by using the “+” and “-”

buttons to set the hour and minute and press the “alarm” button to confirm each. To turn either

alarm on or off, toggle the “+” button and you will see a bell icon for alarm 1 or alarm 2 or both

or none.

y Snooze/Light – when the alarm goes off, press the “snooze” button to go into snooze mode and

the alarm will go off again after 9 minutes and then continue to do this every 9 minutes. To stop

the snooze, press the “alarm” button. To enable the backlight for a moment just push the

“snooze/light” button in normal mode and for having the light on for a longer time keep holding

down the button.

y Channel – if your Sensor is set correctly to Channel 1, then a small icon to the left of outdoor

temperature display will show a “1” in a box. If you do not have an outdoor temperature and

humidity display, make sure that the “1” is displayed and if not (shows a 2 or 3), then push the

“CH” button until it shows the “1”.

Specifications:

y Indoor Temperature Range = 0º to +50º C (+ 32º to + 122º F)

y Remote Sensor Temperature Range = -20º to + 60º C (-4º to + 140º F)

y Indoor/Outdoor Humidity Range = 20% to 95% Relative Humidity

y Resolution = ± .5º C (± 1.5º F) for temperature & ± 1.5% humidity

y Altimeter = 328 ft to 8202 ft (100 m to 2500 m)

y Barometer = 26.80 to 31.01 in/Hg (900 to 1050 mb/hPa)

y Clock = digital quartz

y Transmission = RF433 MHz

y Dimensions = Receiver – 4.0” x 1.0” x 10.0” (102mmx25mmx254mm) Sensor - 2.5” x 1.0” x

3.6” (63mm x 25mm x 91 mm)

y Weight = Receiver - 14oz/397g Sensor - 3oz/85g

2835 Columbia St.

Torrance, California 90503 U.S.A.

www.celestron.com

Printed in China 0110 RoHS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Celestron 47005 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info