Bedienungsanleitung Ciclo CM 8.2 Master (Seite 3 von 10) (Englisch)

588919

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

Congratulations on your purchase!

By purchasing the CICLOMASTER CM 8.2 you have acquired an electronic multifunctional sports com-

puter with the highest level of precision and newest digital transmission technology. The CM 8.2 has a

state of-the-art electronics, is waterproof and convinces through his high durability.

It’s special feature: Transmission from transmitter to device is implemented on a digital communication

level and this makes it extremely faultresistant. The CM 8.2 has a Two-in-One system. This means that

you can use it with 2 bikes and have the recorded values displayed separately for either bike or as a total.

In this case, the CM 8.2 automatically identifies immediately, after the first wheel rotations, which of the

two bikes is being used.

As another special features the CM 8.2 has an optional cadence measurement and an optional heart rate

measurement (for this you need separately available accessories ).

In order to use all functions of the CM 8.2 in the correct way, please read through this

operating manual carefully.

Content:

- CICLOMASTER CM 8.2

- battery type CR 2032

- battery cap

- handlebar bracket

- transmitter

- cable ties for mounting

- spoke magnet

1. General information:

CM 8.2 has three modes: Bike 1 a, Bike 2 b, and Non-Bike mode.

To switch from one mode to another, simultaneously press the right and left buttons briefly (switching

is only possible if speed SPD = 0). In the Non-Bike mode, only bicycle independent functions will be

displayed.

CM 8.2 has an automatic energy save mode: If bike 1 or 2 does not receive any signals for more than

5 minutes and you don’t press any button during this time, the display will be switched off (in the non-bike

mode it will be turned off after 15 hours.)

By pressing any button the display will be switched on again.

Because of the new digital transmission technique, the transmitters have to be initialized before using

CM 8.2 for the first time. We recommend initializing the transmitters before mounting the CM 8.2 on

the bike.

2. Installation

Picture A: Mounting is possible on handlebar (Position A-1) or stem (Position A-2).

Picture B: For using it on the stem (Position A-2), rotate upper part.

Remove the protective tape.

Place the handle bar and fasten it with the cable ties.

Picture C: Mount the transmitter with cable ties on the fork an cutt the ends

Picture D: Fix the magnet on a spoke so that it will face the mark on the transmitter. Adjust the magnet

position and fine tune the sensor if necessary (distance between transmitter and magnet max.

3 mm).

Picture E: Rotate the CM 8.2 to 45 degree left and install it into the bracket. Then rotate it 45 degrees

right to lock it. To unlock, rotate 45 degrees to the left.

A-1A

90ϒ

45ϒ

KLICK!

A-2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ciclo CM 8.2 Master Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ciclo CM 8.2 Master

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info