Bedienungsanleitung Ciclo CM 8.2 Master (Seite 4 von 10) (Englisch)

588919

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

2.1 Mounting of optional cadence-set

Mount the handlebar unit as described above.

Place the transmitter on the cable in front of the crank (don‘t fasten

cable-ties yet). Mount the cadence-magnet on the crank (max. distance

3 mm). Important! The magnet must point directly towards the mark on

the transmitter.

Now switch CM 8.2 cadence measuring on and - if not done yet - initi-

alize the transmitter (see chap.5).

Turn the crank a few times to check if the mounting has been done

correctly so that CM 8.2 receives the signal.

Now tighten the cable-ties.

2.2 Putting on the heart rate transmission belt

Warning: whoever carries out sport should have a general medical

check up on his/her general state of health -especially beginners,

persons older than 35 years of age and anyone who has suffered from

illnesses or injuries in the past. It is recommended that a doctor be

consulted in any case in the presence of risk factors, such as smoking,

high blood pressure, high cholesterol values, diabetes, lack of exercise

and excess weight.

Pacemaker wearers should consult their doctor before using

any heart rate measurement device!

The transmitter belt is hung in the elas-

tic chest belt and fastened around the

upper body. The transmitter (plastic part

with the Ciclo-logo) should lie over the

centre of the upper stomach, immedi-

ately below the breastbone, so that the

logo on the transmitter is legible (viewed

from the front) (see illustration). The

electrodes in the belt, to the right and left

of the transmitter, must be in contact with the skin.

Pull the belt tight so that it cannot slip and constant contact with the

body is guaranteed during movement.

Measurement of the heart rate is only possible if:

- Transmitter belt is fitted correctly

- Measurement of the heart rate is switcht on

- Heart rate transmitter has already been initialized

- CM 8.2 is within the transmitter’s reception range

If the CM 8.2 fails to display any heart rate, it probably means that

there is no contact between the skin and the electrodes. Moistening the

electrodes and the underlying skin often helps. Best results are obtained

if electrode gel is used (available from pharmacies).

3. Operational Setup

Inserting the battery

Insert battery type CR2032 with plus-pole facing up. Close battery

cap with a coin, being sure not to over tighten. After inserting the battery

the display will show normal mode.

(If nothing or incomprehensible signs are displayed, press the AC-but-

ton on the backside of the computer with help of a ballpoint pen or a

similar object. Attention: this will delete all values and setting).

Indication: Because of a special movement-sensor (Motion Switch)

CM 8.2 will start searching for the transmitter signals automatically as

soon as it is moved. For this reason, you might here some noises when

moving CM 8.2 - this is normal.

4. Funcionality of CM 8.2

Because of the respective transmitter identification CM 8.2 can automa-

tically identify on which bike it is being used.

It is necessary for CM 8.2 to be located in the handlebar bracket. Only

in this position can it search for, and receive the transmitted signal from

the motion sensor when the bike starts to move.

During the search for the transmission, „searching“ will flash on the

display. When the transmission has been found, the flashing stops and

the normal setting mode will be displayed.

The CM 8.2 transmitter search can also be started manually by pressing

the right button for 3 seconds.

The manual transmitter search function will only work, if a transmitter

signal has not yet been detected. (‚ – ‚ displays the current function).

If the cadence transmitter is not mounted this function should been

switched off. The transmitter search would keep on searching which

needs a lot of battery.

To search for heart rate transmission without mounting CM 8.2 on the

handlebar, start the manual search for the signal by pressing the right

button for 3 seconds.

Attention: Because of the automatic transmitter searching function,

triggered by the movement sensor, to save the battery, the CM 8.2

shouldn’t be left on the handlebar if you are not using the bike, or if you

are transporting the biket with a car.

5. Settings

Enter setting mode by pressing centre button for 3 seconds. Display

shows ‘SET BIKE1’ a.

To quit setting mode press again centre button for 3 seconds in any

setting.

(To change the display to german language, press left button short,

display shows ‚LANGUAGE’. Press centre button to choose this function

and then switch between ‘English’ and ‘Deutsch’ with right button. To

store press left button and then get back to setting mode with short

pressing of right button).

Because the CM 8.2 can display german and english words, this manu-

al shows both possibilities.

The different setting modes can be shown by pressing right or left but-

ton, by pressing centre button the shown setting mode is chosen.

Possible setting modes:

SET BIKE1 / SET RAD1

SET CLOCK / SET UHR

SET HR / SET HF

SET MISC

PC LINK / PC VERB

EXIT / ENDE

LANGUAGE / SPRACHE

Each setting mode can have different setting options.

The following is valid for these settings: the blinking value can

be changed with the right button, the value is stored by shortly

pressing the left button and the next value blinks or the next

value appears on the display.

Electrodes

Transmitter

Ciclo CM 8.2 Master Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ciclo CM 8.2 Master

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info