Bedienungsanleitung Cobra MX515SPBI - DYM1588SD (Seite 15 von 19) (Englisch)

634408

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

- 15 -

adapter with light oil. Install the blade adapter on the crankshaft with the "star" away from the engine. Refer to figure 14. Place the

blade with the part number facing away from the adapter. Align the washer over the blade and insert the hex bolt. Tighten the hex

bolt to the torque listed below:

Fig.14

10.3 BLADE MOUNTING TORQUE

Center bolt 40Nm-50Nm, to insure safe operation of your unit. ALL nuts and bolts must be checked periodically for correct

tightness.

After prolonged use, especially in sandy soil conditions, the blade will become worn and lose some of the original shape. Cutting

efficiently will be reduced and the blade should be replaced. Replace with an approved factory replacement blade only. Possible

damage resulting from blade unbalance condition is not the responsibility of the manufacturer.

When you change the blade, Must use the original type marked on the blade (Cobra 263001679)

10.4 ENGINE

Refer to the separate engine manual for engine maintenance instructions.

Maintain engine oil as instructed in the separate engine manual packed with your unit. Read and follow instructions carefully.

Service air cleaner as per separate engine manual under normal conditions.

Clean every few hours under extremely dusty conditions. Poor engine performance and flooding usually indicates that the air

cleaner should be serviced.

To service the air cleaner, refer to the separate engine manual packed with your unit.

The spark plug should be cleaned and the gap reset once a season. Spark plug replacement is recommended at the start of each

mowing season; check engine manual for correct plug type and gap specifications.

Clean the engine regularly with a cloth or brush. Keep the cooling system (blower housing area) clean to permit proper air

circulation which is essential to engine performance and life. Be certain to remove all grass, dirt and combustible debris from the

muffler area.

10.5 CLEAN THE DECK AND CUTTING BLADE

WARING: Before cleaning, stop mower and disconnect spark plug cable.

WARING: The cutting blade continues to rotate for a few seconds after the engine is shut off.

NOTE: Before cleaning, remove the grass bag and discharge channel, and then mount the mulching wedge.

To clean the mower deck underneath follow these steps:

1. Insert the hose connector into the cleaning hole-connector on the deck; ensure they are firmly connected (Fig.15A, Fig.15B);

2. Insert another end of the hose into the water tap and then open the switch

3. Connect the spark plug cable and then start the engine as same as the section 7.2;

4. After operating about five minutes, stop the water and the engine (disconnect the spark plug connection) and check the deck

and cutter, repeat steps 3 to 5 as necessary.

5. After cleaning take away the hose, and store in a clean and safety place;

6. Wipe the water from the deck and cutter surface, and then lightly grease the cutter to avoid corrosion and rust.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cobra MX515SPBI - DYM1588SD Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info