Bedienungsanleitung Concept2 PM2 (Seite 7 von 12) (Englisch)

738057

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

LEVEL iii. Extra Functions (for Advanced Users)

All of the PM2 buttons except the ON/OFF button have extra functions which are activated

when you press and hold down the READY button. These special functions include:

• Two Odometers: one is resettable (trip odometer) and one is not resettable.

• Split Intervals: you can set the PM2 to measure splits at intervals which you set. Each

split will be saved for recall after you finish and can be displayed for six seconds while

you row.

• Drag Factor: you can set the PM2 to display the drag factor which it calculates during

the rundown of the flywheel.

• PM2 Display Test

BUTTON SEQUENCES & DESCRIPTIONS OF EXTRA FUNCTIONS:

▲▲

▲

Hold

down

Custom Splits (distance)

to have splits displayed during your

workout. Repeating this button

sequence will turn off the split

display during your workout. When

the PM2 powers up, splits are off

by default.

Hold

down

Splits On/Off

to perform a self-test including all

segments test. Press ON/OFF to end

the test.

Hold

down

then

press

/500 m



WATT



CAL

➔➔

READY

DISPLAY

PM2

DISPLAY

TEST

to set a time interval for split

measurement. Use the SET DIGITS

buttons to set the split time. Then

press READY when done. Note: your

custom split interval will not be

retained through a power down.

Default value is two minutes.

Hold

down

Custom Splits (time)

SPLITS

READY TIME

READY METERS

READY RECALL

then

press

then

press

then

press

to set a distance interval for split

measurement. Use the SET DIGITS

buttons to set the split distance. Then

press READY when done.

Note: your custom split interval will

not be retained through a power

down. Default value is 500 meters.

DRAG FACTOR

Hold

down

to have a drag factor displayed in the lower right display window.

Repeating this button sequence will turn off the drag factor

display. The drag factor is most helpful if you row on Concept2

Indoor Rowers in different locations and want to be sure the

resistance setting is the same. Check the drag factor on your

“home” machine, and then adjust the damper on the “away”

machine until you get the same drag factor. Typical range for

drag factor on the Indoor Rower is: 103 (damper setting 1)-223

(damper setting 10). When PM2 powers up or resets, the drag

factor display will be off by default.

Note: When a heart rate monitor is being worn, HR will override

the drag factor and will always be displayed.

READY REST

then

press

TWO ODOMETERS

Hold

down

then

press

READY SET DIGITS

Not Resettable

to display cumulative distance rowed.

This odometer is not resettable.

Distance is in kilometers and is only

displayed when READY and are

being pressed.

Hold

down

READY SET DIGITS

Resettable

to display a resettable record of distance

rowed. At 99,999 it rolls over to 00,000.

Press RECALL to reset to 0. Press

READY or ON/OFF to get out of this

function.

then

press

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Concept2 PM2 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info