Bedienungsanleitung Conrad 618495 (Seite 4 von 6) (Deutsch)

699469

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

7. Press the “UP” button repeatedly until the desired weekday setting (weekday or weekday combination)

is displayed. The weekday settings are displayed in the following order:

MO → TU → WE → TH → FR → SA → SU

→ MO TU WE TH FR → SA SU → MO TU WE TH FR SA

→ MO WE FR → TU TH SA → MO TU WE → TH FR SA

→ MO TU WE TH FR SA SU

8. Press the “PROG” button to conrm your selection and to set the off time for the rst program. The

display will show “OFF” (off). Set the turn-off time according to the instructions provided in steps 2 to 8.

9. Press the “PROG” button to program additional turn-on and turn-off times, or press the “OK” button to

select the clock time mode. If you want to program additional turn-on and turn-off times, proceed as

described in steps 2 to 9.

10. In clock time mode, press the “SET” button to select “AUTO”, “OFF” or “ON” mode. The modes are

displayed in the following order.

AUTO (Power switched on. Timer activated)

→ OFF (Power switched off. Timer deactivated)

→ ON (Power switched on. Timer deactivated)

11. In order to delete a program, press the “PROG” button repeatedly until the desired program is displayed.

You have to delete each turn-on and turn-off time separately. Press the “CLEAR” button to delete the

selected program. The program will be deleted immediately without any conrmation prompt.

c) Random function

If the random function is activated it has priority over programmed turn-on and turn-off times. It is not

necessary to program a period during which the random function will activate. The random function will

activate several times randomly between 18:00 and 6:00 o’clock for a maximum ON/OFF cycle of one hour.

Press the “SET” button to select “AUTO” mode. Simultaneously press the “SET” and “UP” buttons to activate

or deactivate the random function. The display will show “RANDOM” indicating the random function being

activated.

d) Countdown function

This function is intended for a device to turn on or off after a certain time has elapsed. The countdown

function is only available in “ON” and “OFF” modes. In “ON” mode, the power will switch off after the set time

has elapsed. In “OFF” mode, the power will switch on after the set time has elapsed. Set the time to elapse

until switching on or off the power as follows:

1. Connect a device and switch it on.

2. Simultaneously press the “PROG” and “UP” buttons to program the countdown function. The display will

show “COUNTDOWN”. Set the time between 1 minute up to 99 hours and 59 minutes.

3. Press the “SET” button. The ► symbol in front of “HOURS” starts ashing.

4. Press the “UP” button repeatedly until the desired hours are displayed. Press and hold the “UP” button to

quickly scan through the hours. Use this procedure to set the “MINUTES” next.

5. Press the “SET” button. The ► symbol in front of “MINUTES” starts ashing.

6. Press the “UP” button repeatedly until the desired minutes are displayed.

7. Press the “OK” button to start the countdown. “COUNTDOWN” starts ashing and the set time starts

counting backwards in the display.

8. After the set countdown has elapsed, the device will turn on or off depending on the respective operating

mode.

9. Simultaneously press the “PROG” and “UP” buttons to deactivate the countdown function.

e) Resetting the device

In case of malfunctions, if the display does not work properly or if pressing a button does not cause any

response of the device, press the red “RESET” button. In order to do so, use an object with a round tip or

the end of a paper clip. All stored data will be reset. You will have to set the clock time and any programmed

times again.

If the rechargeable battery is not completely discharged and still contains a small amount of

power, the display will not turn on. Connect the timer to a wall socket (230 V/AC, 50 Hz) and

press the “RESET” button to reset the device and to activate the display.

If the built-in battery is completely discharged, connect the timer to a wall socket. The display

will turn on immediately.

Maintenance and cleaning

Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as they

can cause damage to the housing and malfunctioning.

• Unplug the timer from the wall socket before cleaning.

• Never submerge the product in water or other liquids.

• There are no user-serviceable parts inside the product. Never open/dismantle the product.

• To clean the product, a dry, soft and clean cloth is sufcient. Do not apply too much pressure to the housing

to prevent scratching.

• You can easily remove dust using a long-haired, soft and clean brush.

Disposal

a) Product

Electronic devices are recyclable waste and must not be disposed of in the household waste.

At the end of its service life, dispose of the product according to the relevant statutory regulations.

The built-in battery must be disposed of by a specialist.

b) (Rechargeable) batteries

You as the end user are required by law (Battery Ordinance) to return all used batteries/rechargeable

batteries. Disposing of them in the household waste is prohibited.

Contaminated (rechargeable) batteries are labelled with this symbol to indicate that disposal

in the domestic waste is forbidden. The designations for the heavy metals involved are: Cd =

Cadmium, Hg = Mercury, Pb = Lead (name on (rechargeable) batteries, e.g. below the trash

icon on the left).

Used (rechargeable) batteries can be returned to collection points in your municipality, our stores

or wherever (rechargeable) batteries are sold.

You thus full your statutory obligations and contribute to the protection of the environment.

Technical data

Operating voltage ............................. 230 V/AC, 50 Hz

Backup battery .................................. 1 x 2.4 V, 40 mAh NiMH rechargeable battery

Switching power ...............................max. 3680 W

Switching current .............................. max. 16 A

Standby power consumption ............ 0.45 W

Programs .......................................... 16 turn-on and turn-off programs

Setting time ....................................... min. 1 minute, max. 7 days

Time display .....................................24 or 12 hours

Storage/operating temperature ......... 0 to 50° C

Dimensions (W x H x D) ................... 73 x 145 x 80 mm

Weight ..............................................202 g

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau

(www.conrad.com).

All rights including translation reserved. Reproduction by any method, e.g. photocopy, microlming,

or the capture in electronic data processing systems require the prior written approval by the editor.

Reprinting, also in part, is prohibited. This publication represent the technical status at the time of

printing.

2016

by Conrad Electronic SE.

V3_0416_02-HK

Conrad 618495 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info