648532
4
Zoom out
Zoom in
Vorherige Seite
1/8
Nächste Seite
6 • EN
MODE
START
STOP
STOP
SUPPLY
BOOST
Ca/Ca
AGM
NORMAL
SET
1 2 3 4 5 6 7 8
12V/40A
24V/20A
MXTS 40
INCREASE BUTTON
DISPLAY (A)
12V
0.00h
40A
0Ah
DISPLAY (Ah & info)
SET-BUTTON
DISPLAY (h)
DISPLAY (V)
NORMAL PROGRAM
DECREASE BUTTON
MODE-BUTTON
START/STOP-BUTTON
REVERSED POLARITY
BATTERY TEMPERATURE
OUT OF RANGE
OVERVOLTAGE ERROR
AGM PROGRAM
Ca/Ca PROGRAM
BOOST PROGRAM
SUPPLY PROGRAM
CHARGING
For best possible charging of your batteries the voltage and current is
adjustable. In addition temperature compensated charging is selectable.
See below how to set the parameters for customized charging.
1. Connect the charger cables to the charger
(see quickguide).
2. Connect the charger to the battery
(see quickguide).
3. Connect the charger to the mains supply
4. Turn on the mains switch
The power lamp will indicate that the mains cable is connected to the
mains supply. The error lamp will indicate if the battery clamps are
incorrectly connected. The reverse polarity protection will ensure that
the battery or charger will not be damaged.
5. Press the MODE-button to select charging program
6. Press SET-button to set parameters
7. Select voltage
Display (h) will indicate that voltage (
V
) is selectable.
Display (V) will flash and indicate set voltage.
Press +/- to change.
Press SET-button to confirm.
8. Select current
Display (Ah & info) will indicate that current (
A
) is selectable.
Display (A) will flash and indicate set current.
Press +/- to change.
Press SET-button to confirm.
9. Select temperature compensation
•Display (h) will indicate that temperature compensation (
T
) is
selectable.
Display (Ah & info) will indicate On
/
Off.
Press +/- to change.
Press SET-button to confirm.
10. Press the START/STOP-button to start charging cycle
or press MODE-button to change charging program
11. Follow the 8-step display through the charging
process
The battery is ready to start the engine when STEP 4 is lit. The battery
is fully charged when STEP 7 is lit.
12. Stop charging at any time by pressing the
START/STOP-button
13. Press START/STOP-button to start charging cycle
POWER LAMP
ERROR LAMP
4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Ctek MXTS 40 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Ctek MXTS 40

Ctek MXTS 40 Bedienungsanleitung - Deutsch - 16 seiten

Ctek MXTS 40 Bedienungsanleitung - Holländisch - 8 seiten

Ctek MXTS 40 Bedienungsanleitung - Französisch - 8 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info