Bedienungsanleitung Dali HELICON (Seite 6 von 29) (Deutsch, Dänisch)

562737

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

ENGLISH

When you have decided upon which method of connection you want and positioned the subwoofer (see

the chapter “Positioning Loudspeakers – HELICON S600/S600MK2”), you can commence the exciting

process of adjusting the system. Please note that positioning the subwoofer will have a lot of inﬂuence

on its contribution to the overall sound. If for example, the subwoofer is positioned in a corner, the bass

level will be much higher than if it is positioned midway between two corners (due to acoustic loading of

the subwoofer). If using the subwoofer in conjunction with the C200 center loudspeaker, the subwoofer

should be positioned so that the C200 can stand on top of the subwoofer.

The following adjustment methods are recommended to

achieve the best results. Use a piece of music you know

well, and that preferably includes rhythmic bass such as

kettle drums, bass guitar etc.

Start with "VOLUME" and "CROSSOVER" in the middle

of the dial (12 o’clock). Turn the "PHASE" switch to posi

tion 180°, and "POWER" to the "ON" position.

ADJUSTMENT OF HELICON S600/S600MK2

ENGLISH

VOLUME ADJUSTMENT

Adjust the volume of the subwoofer so that the bass matches the level of the front speakers. You

should be able to appreciate the subwoofer’s contribution to the sound, without it ever being over-

powering. Bass must be tight and accurate, so that the subwoofer reproduces the exact amount of

bass present in the music/soundtrack, no more and no less. If installing the subwoofer in a surround

sound system, it is practical to select a ﬁxed level on the subwoofer and adjust subwoofer output us

ing the surround ampliﬁer's set-up function. If bass levels are set too high, distortion will reduce the

quality of your listening experience. Please note that the position of the subwoofer will have major

inﬂuence on its sonic contribution.

ADJUSTING THE CROSSOVER FREQUENCY

Once the volume level is adjusted, you can start the equally important adjustment of the overlap between

the front loudspeakers and the subwoofer. To do so, adjust up and down using "CROSSOVER" until you

can hear that the bass is even and with no drop-out. You may have to adjust the volume again.

SELECTING AUTO FUNCTION

The "AUTO" function puts the subwoofer into standby after approx. 10 minutes with no signal

received at the inputs. When a signal is present again on one of the inputs, the built-in subwoofer

ampliﬁer powers up automatically. The "POWER" button is the main on/off switch. We recommend

switching off the system when it is not to be used for long periods. When connecting or changing

connections, always disconnect the mains electricity.

er exclusively reproducing the low frequencies. From the output socket “LINE OUT - LEFT” a highpass

ﬁltered signal may be tapped, as when using a stereo connection. Please note that there is no signal

available on the “LINE OUT - RIGHT” socket.

Connecting to a Lowpass Filtered Mono Signal

When using the subwoofer with a surround ampliﬁer or

other equipment with access to a ﬁltered mono output

for subwoofer use, it is advantageous to connect this

signal to the subwoofer´s input marked “LFE”. When the

subwoofer is connected via “LFE“, the signal bypasses the

crossover network and goes directly to the ampliﬁer. In

this setup, there is no signal available at the output “LINE

OUT”. Any adjustment of the crossover frequency takes

place elsewhere in the system, typically the surround

processor/ampliﬁer. Please follow the instructions provided in that component’s manual. When using

the “LFE” input, the level and phase controls of the S600 are still active and these should be adjusted

as recommended in the section concerning adjustments.

PRE-/SURROUND

AMPLIFIER

SUB OUTPUT

LINE IN

POWER AMPLIFIER

LOUDSPEAKER OUTPUT

SETTING PHASE

Try both settings – if necessary combined with new adjustment of volume and crossover frequency. In

any event, it is a good idea to listen to the system for a few days before making any ﬁnal adjustments.

Using the same setting for surround sound and stereo does not always achieve the best results. It is

therefore a good idea to note the setup you prefer for surround sound and stereo setups.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dali HELICON Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dali HELICON

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info