381482

DeWalt dc 845 kb Seite 2

2
Zoom out
Zoom in
Vorherige Seite
1/10
Nächste Seite
DC830,DC835,
DC840
, DC845
CORDLESS IMPACT WRENCHES/DRIVERS
Technical data
DC830 DC835 DC840 DC845
Voltage V
DC
14.4 14.4 12 12
Battery Type NiCd - ALL VOLTAGES
No-load
speed min
-1
0-2400 0-2400 0-2400 0-2400
Impact min
-1
2700 2700 2700 2700
Max. torque Nm 180 140 160 130
Tool holder 1/2" 1/4" 1/2" 1/4"
Square Hex Square Hex
Max
. bolt size mm M16 M12 M16 M12
General Power Tool Safety Warnings
WARNING! Read all safety warnings
and
instructions. Failure to follow the
warnings
and instructions may result in
electric
shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE.
ELECTRICAL SAFETY
a)
Power tool plugs must match the outlet.
Never
modify the plug in any way. Do
not
use any adapter plugs with earthed
(grounded)
power tools. Unmodified plugs
and
matching outlets will reduce risk of
electric
shock.
b)
Avoid body contact with earthed or
grounded
surfaces such as pipes,
radiators,
ranges and refrigerators. There
is
an increased risk of electric shock if your
body
is earthed or grounded.
c)
Do not expose power tools to rain or wet
conditions.
Water entering a power tool will
increase
the risk of electric shock.
PERSONAL
SAFETY
a)
Use personal protective equipment.
Always
wear eye protection. Protective
equipment
such as dust mask, non-skid
safety
shoes, hard hat, or hearing protection
used
for appropriate conditions will reduce
personal
injuries.
b) Do not overreach. Keep proper
footing
and balance at all times.
POWER
TOOL USE AND CARE
a)
Do not force the power tool. Use the
correct
power tool for your application.
The
correct power tool will do the job
better
and safer at the rate for which it
was
designed.
b)
Do not use the power tool if the switch
does
not turn it on and off. Any power
tool
that cannot be controlled with the switch
is
dangerous and must be repaired.
c)
Disconnect the plug from the power
source
and/or the battery pack from
the
power tool before making any
adjustments,
changing accessories, or
storing
power tools. Such preventive safety
measures
reduce the risk of starting the
power
tool accidentally.
d)
Use the power tool, accessories and
tool
bits etc., in accordance with these
instructions
taking into account the
working
conditions and the work to
be
performed. Use of the power tool for
operations
different from those intended
could
result in a hazardous situation.
BATTERY TOOL USE AND CARE
a)
Recharge only with the charger specified
by
the manufacturer.
b)
Use power tools only with specifically
designated
battery packs.
c)
When battery pack is not in use, keep it
away
from other metal objects like paper
clips,
coins, keys, nails, screws or other
small
metal objects that can make a
connection
from one terminal to another.
Shorting
the battery terminals together may
cause
burns or a fire.
d)
Under abusive conditions, liquid may be
ejected
from the battery, avoid contact.
If
contact accidentally occurs, flush with
wate
r. If liquid contacts eyes, additionally
seek
medical help. Liquid ejected from the
batte
ry may cause irritation or burns.
Important Safety Instructions for All
Battery Chargers
WARNING: Shock hazard. Do not allow
any
liquid to get inside charger. Electric
shock
may result.
CAUTION: Burn hazard. To reduce
the
risk of injury, charge only DEWALT
rechargeable
batteries. Other types of
batteries
may burst causing personal
inju
ry and damage.
CAUTION: Under certain conditions,
with
the charger plugged in to the
power
supply, the exposed charging
contacts
inside the charger can be
shorted
by foreign material.
• DO NOT attempt to charge the battery pack
with
any chargers other than the ones in
this
manual. The charger and battery pack are
specifically
designed to work together.
• These chargers are not intended for
any
uses other than charging D EWALT
rechargeable
batteries. Any other uses
may
result in risk of fire, electric shock or
electrocution
.
• Do not expose charger to rain or snow.
• Pull by plug rather than cord when
disconnecting
charger.
• Do not use an extension cord unless it
is
absolutely necessary.
• Do not place any object on top of charger
or
place the charger on a soft surface that
might
block the ventilation slots and result
in
excessive internal heat.
• Do not operate charger with damaged cord
or
plug
• Do not operate charger if it has received
a sharp blow, been dropped, or otherwise
damaged
in any way.
• Do not disassemble charger; take it to an
authorized
service center when service or
repair
is required.
• Disconnect the charger from the outlet
before
attempting any cleaning. This will
reduce
the risk of electric shock. Removing
the
battery pack will not reduce this risk.
• NEVER attempt to connect 2 chargers together.
Charging Procedure
1. Plug the charger (j) into an appropriate outlet
befo
re inserting battery pack.
2. Insert the battery pack (h) into the charger.
The
red (charging) light will blink continuously
indicating
that the charging process has started.
3. The completion of charge will be indicated by
the
red light remaining ON continuously. The
pack
is fully charged and may be used at this
time
or left in the charger.
Charging process
Refer the table below for the state of charge of the
battery
pack.
State of charge
charging – – – – – –
fully charged –––––––––––
hot/cold pack delay ––– – ––– –
replace battery pack •••••••••••
problem •• •• •• ••
Automatic refresh
The automatic refresh mode will equalise or balance
the
individual cells in the battery pack at its peak
capacit
y. Battery packs should be refreshed weekly
or
whenever the pack no longer delivers the same
amount
of work.
To refresh your battery pack, place the battery in the
charger
as usual. Leave the battery pack for at least
8 hours in the charger.
Hot/Cold Pack Delay
When the charger detects a battery that is too hot
or
too cold, it automatically starts a Hot/Cold Pack
Dela
y, suspending charging until the battery has
reached an appropriate temperature. The charger
Important Safety Instructions for All
Batte
ry Packs
• Charge the battery packs only in DEWALT
chargers
.
• DO NOT splash or immerse in water or other
liquids
.
• Do not store or use the tool and battery
pack
in locations where the temperature
may
reach or exceed 40˚ C (105° F)
DANGER: Electrocution hazard. Never
attempt
to open the battery pack for
any
reason.
WARNING: Never attempt to open the
batte
ry pack for any reason. If battery
pack
case is cracked or damaged, do
not
insert into charger. Do not crush,
drop
or damage battery pack. Do not
use
a battery pack or charger that has
received
a sharp blow, been dropped,
run
over or damaged in any way (i.e.,
pierced
with a nail, hit with a hammer,
stepped
on).
2 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für DeWalt dc 845 kb wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info