381482

DeWalt dc 845 kb Seite 3

3
Zoom out
Zoom in
Vorherige Seite
1/10
Nächste Seite
• Do not incinerate the battery pack even if it
is
severely damaged or is completely worn
out.
The battery pack can explode in a fire.
• A small leakage of liquid from the battery
pack
cells may occur under extreme usage
or
temperature conditions . This does not
indicate
a failure.
However, if the outer seal is broken:
a.
and the battery liquid gets on your skin,
immediately
wash with soap and water for
several
minutes.
b. and the battery liquid gets into your eyes,
flush
them with clean water for a minimum
of
10 minutes and seek immediate medical
attention.
(Medical note: The liquid is
25-35%
solution of potassium hydroxide.)
Battery Cap (fi
g. 3)
A protective battery cap is supplied to cover the
contacts
of a detached battery pack. Without the
protective cap in place, loose metal objects could
short
circuit the contacts, causing a fire hazard and
damaging
the battery pack.
1. Take off the protective battery cap before
placing
the battery pack in the charger
or
tool (Fig. 3A).
2. Place the protective cap over the contacts
immediately
after removing the battery pack
from the charger or tool (Fig. 3B).
WARNING: Make sure the protective
batte
ry cap is in place before storing or
car
rying a detached battery pack.
Battery pack (fi g. 1)
BATTERY TYPE
The DC830, DC835, operate on
14.4
volt battery packs.
The
DC840 and DC845 operate on 12 volt battery
packs.
Labels on charger and battery pack
Battery charging.
Battery charged.
Battery defective.
Hot/cold pack delay.
Do not probe with conductive objects.
Do not charge damaged battery packs.
Use only with D EWALT battery packs,
others
may burst, causing personal injury
and
damage.
Do not expose to water.
Have defective cords replaced
immediatel
y.
Charge only between 4 °C and 40 °C.
Discard the battery pack with due care for
the
environment.
Do not incinerate the battery pack
NiMH,
NiCd+ and Li-Ion.
Charges NiMH and NiCd
battery
packs.
Package contents
The package contains:
1 Cordless Impact Driver/Wrench
2 Battery packs
1 Charger
1 Instruction manual
NOT
E : Battery packs and chargers are not included
with
N-models.
• Check for damage to the tool, parts or
accessories
which may have occurred during
transport
.
• Take the time to thoroughly read and
understand
this manual prior to operation.
Description (fi g. 1–5)
INTENDED USE
These
heavy-duty impact wrenches/drivers are
designed
for professional impact screwdriving
applications.
The
impact function makes this tool particularly
useful
for driving fasteners in wood, metal and
conc
rete.
DO
NOT use under wet conditions or in presence of
flammable
liquids or gases.
a. Trigger switch
b. Forward/reverse button
c. Sleeve
d. hex quick-release chuck
e. Detent pin
f. Anvil
g. Worklight
h. Battery pack
i. Battery release buttons
Inserting and removing the
battery pack from the tool (fi
g. 2)
TO
INSTALL BATTERY PACK INTO THE TOOL
1. Align the base of the tool with the notch inside
the
tool’s handle (Fig. 2).
TO
REMOVE BATTERY PACK FROM THE TOOL
1. Press the battery release buttons (i) and firmly
pull
the battery pack out of the tool handle.
OPERATION
Variable Speed Trigger Switch
(fi g. 1)
To turn the tool on, squeeze the trigger switch (a).
To turn the tool off, release the trigger switch.
Your tool is equipped with a brake. The chuck will
stop
as soon as the trigger switch is fully released.
NOTE:
Continuous use in variable speed range is
not
recommended. It may damage the switch and
should
be avoided.
Forward/Reverse Control Button
(fi g. 1)
To select forward rotation,
switch
and depress the forward/reverse control
button
on the right side of the tool.
To select reverse, depress the forward/reverse
cont
rol button on the left side of the tool.
The
center position of the control button locks the
tool
in the OFF position. When changing the position
of
the control button, be sure the trigger is released.
Worklight (fi g. 1)
There is a worklight (g) located just above the trigger
switch
(a). The worklight will be activated when the
trigger
switch is squeezed.
Quick-Release Chuck (fi g. 4)
DC835, DC845 Drivers
Place
the switch in the locked off (center) position or
remove battery pack before changing accessories.
To install an accessory, pull the chuck collar (c)
away
from the front of the tool, insert the accessory
and
release the collar. The accessory is locked in
place
.
To remove an accessory, pull the chuck collar
away
from the front of the tool. Remove the
accessory
and release the collar.
Anvil With Detent Pin (fi
g. 5)
DC830 , DC840 Wrenches
Place
the switch in the locked off (center) position or
remove battery pack before changing accessories.
To install a socket on the anvil, align the hole in
the
side of the socket with the detent pin (e) on the
anvil
(f). Press the socket on until the detent pin
engages
in the hole. Depression of detent pin may
be
necessary to aid installation of socket.
CAUTION: Use only impact sockets.
Non-impact
sockets may break and
cause
a hazardous condition. Inspect
sock
et prior to use to ensure that it
Usage
Your impact tool generates the following output
to
rque:
Cat # Ft.-Lbs. In.-Lbs. Nm
DC830 135 1620 180
DC835 103 1240 140
DC840 120 1440 160
DC845 96 1150 130
CAUTION: Ensure fastener and/or
system
will withstand the level of torque
generated
by the tool. Excessive torque
may
cause breakage and possible
personal
injury.
WARNING: To reduce the risk of
serious
personal injury, turn tool off
and
disconnect battery pack before
making
any adjustments or removing/
installing
attachments or accessories.
An
accidental start-up can cause injury.
MAINTENANCE
Your D EWALT power tool has been designed to
operate
over a long period of time with a minimum
of
maintenance. Continuous satisfactory operation
depends
upon proper tool care and regular cleaning.
Separate collection. This product must
not be disposed of with normal
household
waste.
CHARGER
CLEANING INSTRUCTIONS
WARNING: Shock hazard. Disconnect
the
charger from the AC outlet before
cleaning. Dirt and grease may be
removed
from the exterior of the charger
using
a cloth or soft non-metallic brush.
Do not use water or any cleaning
solutions
.
Rechargeable Battery Pack
This long life battery pack must be recharged when
it
fails to produce sufficient power on jobs which
were easily done before. At the end of its technical
life,
discard it with due care for our environment:
3 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für DeWalt dc 845 kb wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info