Bedienungsanleitung Dimplex Cadiz Eco CDE3ECC (Seite 4 von 8) (Englisch)

798035

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

be noticed, this is quite normal – the fumes are non-toxic

and will quickly disappear. We recommend that you open a

window to ventilate the room when using the heater during

this time.

Used in an environment where background noise is very

low, it may be possible to hear a sound which is related to

the element. This is normal and should not be a cause for

concern.

ELECTRICAL

WARNING: THIS APPLIANCE MUST BE EARTHED

The use of an extension lead or multi-plug adaptor is

not advised when connecting this product to the mains.

Connection through these devices could lead to a risk of

overloading, overheating and even re at the extension lead

or adaptor due to inadequate connection quality.

If the socket outlets in your home are not of the 13 amp

BS1363 type they will not accept the plug connected to this

heater, therefore cut off the plug. When cut off this plug can

constitute a shock hazard if inserted into a socket outlet. It

must therefore be disposed of safely.

Before wiring the appropriate plug please note that the

wires in this mains lead are coloured in accordance with

the following code:

GREEN/YELLOW: EARTH

BLUE: NEUTRAL

BROWN: LIVE

Connect the Green/Yellow wire to the terminal marked E

or the earth symbol or coloured Green or Green/Yellow.

Connect the Brown wire to the terminal marked L or coloured

Red. Connect the Blue wire to the terminal marked N or

coloured Black.

DO NOT connect the Brown (Live) or the Blue (Neutral)

wires to the Earth terminal of your 13 amp plug. If the

terminals of the plug are unmarked or you are in any doubt,

consult a qualied electrician.

CAUTION: If you use this heater in conjunction with a

thermal control, programme controller, timer or any other

device which switches the heater on automatically observe

all safety warnings at all times.

Positioning the Heater

Select the position for the heater ensuring there is clearance

from any furniture and ttings of at least 300mm above the

heater and 150mm each side. The appliance should only

be operated on a at stable surface.

Operation

Important: Objects or clothing must not be placed on this

heater. Before using the heater ensure that all warnings

and instructions have been read carefully.

To bring the heater into use plug it in. Neon indicating lights

located at the controls area will glow when the appliance

is actually heating.

CONTROLS

Thermostat

(CDE2T, CDE2TI & CDE3TIE models only)

The Thermostat (see ‘T’ in Fig.’s 2 & 3) controls the heat

output according to the room temperature. This ensures

that the heater will not produce heat unnecessarily when

the room is warm. To set the temperature you require, turn

the thermostat knob clockwise until the required setting

is reached. Alternatively to heat a cold room quickly, turn

the thermostat knob up fully. When the room has reached

the desired temperature, turn the thermostat knob anti-

clockwise until the thermostat just clicks off. The heater

will now automatically operate at this temperature. The

thermostat also has a frost protection setting marked ‘ ‘.

This setting is useful in areas such as garages, to prevent

frost damage. If the thermostat is set to its minimum

setting ‘ ’, the heater will cycle on and off to maintain a

temperature of approximately 5° to help protect against frost.

Note – Should the heater fail to come on when the

thermostat is at a low setting, this may be due to the room

temperature being higher than the thermostat setting.

On/Off button (CDE2T &CDE2Ti Models Only)

This button controls the electricity supply to the elements.

When the On/Off button is activated a neon light ‘Y’

illuminates above the control button.

To turn off press the button ‘O’ located directly above the

On/Off button.

Mono and Dual Panel Heat Selection

Switches

(CDE2T, CDE2TI & CDE3TIE models only)

Selector switches located on the control panel provide

a choice of Half Heat or Full Heat output to suit varying

conditions and for economy of operation as follows:

Half Heat Setting - left hand side - This switch as

shown in Fig.’s 2 & 3 provides half heat output when

activated. When it is activated a neon light ‘x’ illuminates

above the control button and the left hand side element

turns on.

Half Heat Setting - right hand side - This switch as

shown in Fig.’s 2 & 3 provides a half heat output when

activated. When it is activated a neon light ‘x’ illuminates

above the control button and the right hand side element

turns on.

Centre ECO Element (CDE3Tie Only)- This model has an

additional central element which provides a boost of heat

to either the left hand or right hand element operation if

they do not provide enough heat output on their own. The

neon ‘Y’ above the button illuminates when it is activated.

This feature can also be used on its own as an ECO mode

when both heat panels are switched off to provide a low

level background heat.

Maximum Heat Setting

CDE2T &CDE2Ti Models - Maximum output is achieved

with both left and right hand side switches on and all neons

illuminated (see Fig.’s 2 & 3). Note that these models wil

only operate with the On/Off button in the On position and

all neons illuminated.

CDE3Tie Model - To achieve maximum heat output on this

model Left, Right and ECO elements must all be switched

on with all neons illuminated.

Dimplex Cadiz Eco CDE3ECC Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info