Bedienungsanleitung Dimplex Cadiz Eco CDE3ECC (Seite 6 von 8) (Englisch)

798035

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

ELECTRONIC CLIMATE CONTROL

see Fig. 4

(CDE2ECC & CDE3ECC models only)

Operation

The electronic control allows MANUAL and AUTO

operation.

In MANUAL ON mode there are three heat settings:

L/H Side Heat, R/H Side Heat and High Heat

In AUTO mode the heater comes on as per the programmed

timer settings (see Setting programs). At any point if the

heater is active i.e. heat is being produced, the ‘ ’ neon is

lit - see Fig. 4.

Initial Operation

When the heater is connected to the mains the ‘ ’ neon will

be lit and the display is blank. Press the ‘ ’ button and the

display goes to full heat set to 35oC - see Fig. 8.

Note: All display characters are displayed in Fig. 13.

Standby Mode

With the heater ON if the ‘ ’ button is pressed, the heater

will go into standby mode, heater switches off, the display

goes blank and only the MAINS ON neon ( ) remains lit.

On pressing the ‘ ’ button again the heater will come on

in the mode and with the settings it had prior to going into

standby mode.

Setting Current Time

1. Press and hold ‘ ’ and the clock symbol ‘ ’ appears

on the top left hand side of the screen. The user can

now set the time.

2. The hour digit will now ash. To adjust the hour use the

‘’ & ‘ ’ buttons. Conrm the hour digit by pressing ‘

’.

3. The minute digit will ash. To adjust the minute use the

‘’ & ‘ ’ buttons. Conrm the hour digit by pressing ‘

’. The display will return to the state before

entering set time.

N.B. If no keys are pressed after 4 minutes the display will

revert to the state prior to entering set time.

Manual Operation

Pressing ‘ ’ from the default HIGH screen (Fig. 8) brings

the heater into AUTO mode - see ‘Setting the Timer

Programs’. Press again to put the heater into OFF mode -

see Fig. 6. Press again for left hand side heat ( appears

on LCD display - see Fig. 7). Press again for right hand

side heat ( appears on LCD display). Press again brings

the user full circle to FULL heat mode ( appears

on LCD display).

Setting the Desired Temperature

The desired temperature can be set using the ‘ ’ or ‘

’ keys. The temperature can be set from 5oC to 35oC and

this will be shown on the display. When the temperature

is reached the heater will automatically switch OFF. If the

ambient temperature drops the heater will come on again

automatically. Note the electronic climate control device

conserves energy and assists with temperature regulation

e.g. if the heater is set to HIGH heat and the temperature

is set to 28oC, at 27oC the heater will switch to a lower heat

setting. Then at 28oC the heater will switch off completely.

Setting the Timer Programs

Two program settings are possible, P1 and P2. Only high

heat is possible for program settings. Press ‘ ’ once to set

the programs, starting with P1 AUTO ON – See Fig 10.

1. The hour digit will now ash. To adjust the hour use the

‘’ & ‘ ’ buttons. Conrm the hour digit by pressing ‘

’.

2. The minute digit will now ash. To adjust the minute

use the ‘ ’ & ‘ ’ buttons. Conrm the hour digit by

pressing ‘ ’.

3. Now P1 AUTO OFF is displayed, P1 off time can now

be set. Repeat steps 1 & 2 to set P1 off time.

At this point either:

(a) Press ‘ ’ to exit the Program mode and return

to AUTO mode. The heater is now in AUTO mode.

The heater will switch ON and OFF depending on

programme P1 previously entered.

(b) Repeat steps 1 - 3 as above to set the programme

for P2.

At this point press ENTER or PROG to exit the Programme

mode. The heater is now in AUTO mode. The heater will

switch ON and OFF depending on programme P1 & P2

previously entered. If after programming and returning to

the AUTO mode display, P1 or P2 is active, the display will

show PROG 1 AUTO ON or PROG 2 AUTO ON depending

on which is active - see Fig. 11. An OFF time cannot be

entered which is less than the corresponding ON time.

When setting the timer programs if no keys are pressed, the

display will (after 4 minutes) revert to the previous display

i.e. display prior to entering Program mode.

Run Programs

If MODE is pressed until AUTO appears on the screen

(either AUTO-ON or AUTO-OFF), the heater will run both

P1 and P2 program as they are set.

NOTE: The heater cannot be programmed to run P1

only or P2 only.

To cancel P1, set P1 OFF time to be same as P1 ON time.

To cancel P2 set P2 OFF time to be same as P2 ON time.

Review Program settings

To review the program settings the heater must be in AUTO

mode. Press ENTER and the times for PROG 1 ON, PROG

1 OFF, PROG 2 ON and PROG 2 OFF will be displayed

consecutively for 2 seconds. The display will automatically

return to the state it was in before ENTER was pressed.

FROST Protection Mode

With the heater in any mode, OFF, MANUAL ON or AUTO,

if the displayed set temperature is reduced to 5oC the heater

will go into FROST Protection mode - see Fig. 12. In this

mode only, if the ambient temperature drops below 5oC, will

the heater come on. This is to prevent freezing. In FROST

Protection mode the heater comes on in the high heat mode

only. Pressing the ‘ ’ button is the only way to bring the

heater out of this special mode.

Dimplex Cadiz Eco CDE3ECC Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info