Bedienungsanleitung Dirt Devil M2012-2 (Seite 15 von 17) (Spanisch, Türkisch)

500140

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

5 Maintenance

5.3 Cleaning the exhaust filter

 Clean the filters each time you clean the dust container, ZChapter 5.1,

“Emptying and cleaning the dust container”.

 Clean the filters at the latest when the cleaning/emptying indicator

(Fig. 9/A1) lights up.

1. Switch off the appliance, ZChapter 4.3, “Switching off”.

2. Push the release catch of the exhaust filter cover down (Fig. 13/A) and

open out the exhaust filter cover.

3. Remove the exhaust filter cover with the exhaust filter.

4. Hold the exhaust filter cover complete with the exhaust filter low over a

dustbin.

5. Brush out dirt using a soft brush, such as the 2-in-1 combi brush sup-

plied (Fig. 13/B).

6. If this is not enough, remove the exhaust filter from the exhaust filter

cover using the removal tab and knock out remaining dirt from both el-

ements.

7. If the exhaust filter is still dirty after this procedure, thoroughly rinse it

by hand in running water until all dirt is gone.

8. If the exhaust filter is damaged, deformed or too soiled, replace it (or-

dering information ZChapter 5.4, “Spare parts and accessories”).

9. Put the clean/new and completely dry exhaust filter back into the ex-

haust filter cover. Make sure that, after putting it back in, the removal

tab (Fig. 14/A1) is still visible.

10. Fit the exhaust filter cover with the new or cleaned exhaust filter on the

bottom side first (Fig. 14/A) and then pivot it in upwards. You will feel

and hear it snap into place (Fig. 14/B).

5.4 Spare parts and accessories

 Ordering address: ZPage 77, “International Service”

 Further information: Z www.dirtdevil.de

 The adjacent accessory parts and spare parts can be reordered.

5.5 If the appliance does not work as it should

Before contacting your authorised Royal dealer, Royal service partner or

appliance market or before sending in the appliance (ZPage 77, “Interna-

tional Service”), first follow the procedure in the following table to check if

you can solve the problem yourself.

ATTENTION:

The exhaust filter is washable, but it may not be cleaned in dishwashers

or washing-machines. Also, do not use detergents or brushes with hard

bristles to clean the filters.

ATTENTION:

Let the filter dry for approx. 24 hours at room temperature after wet

cleaning. Only put it back in place when it is completely dry.

ATTENTION:

Only use original spare parts from the scope of delivery or those that you

have purchased by reordering.

Item number Description

2725001 Filter set 3 pcs, consisting of 1 central lamellae filter,

1 motor protection filter, 1 exhaust filter

M203 1 parquet brush

M209 1 turbo brush

M219 1 Mini-turbo brush ‘Fellino’

WARNING:

Danger of injury! Never use a defective appliance! Always switch off the

appliance and disconnect it from the mains before starting troubleshoot-

ing ZChapter 4.3, “Switching off”.

Problem Possible cause / solution

The vacuum

cleaner

stops sud-

denly.

The overheating protection has tripped (possibly due to

blocked suction channels, filters, or similar).

Switch the appliance off and pull the plug out of the socket.

Remove the cause of overheating (e.g. by disassembling

telescopic tube and suction hose and removing the obsta-

cle and/or cleaning filters). Wait for about 45 minutes. After

the appliance has cooled off, you may switch it on again.

Cleaning/

emptying in-

dicator

(Fig. 1/9)

lights up.

The central lamellae filter is dirty.

Clean the central lamellae filter, ZChapter 5.2, “Cleaning

central lamellae filter and motor protection filter”.

The dust container is full.

Empty / clean the dust container. ZChapter 5.1, “Empty-

ing and cleaning the dust container”

The cleaning

results are

unsatisfacto-

ry in spite of

the appli-

ance work-

ing correctly.

The bypass vent (Fig. 1/18) is open.

Close the bypass vent .

The attached nozzle is unsuitable.

Change the nozzle, ZChapter 3.2, “Selecting the proper

nozzle”.

The suction power you set is unsuitable.

Adjust the suction power control to suit the flooring,

ZChapter 4.2, “Vacuum cleaning”, step 4.

The position of the "carpet/hard floor" selector (Fig. 1/31)

is unsuitable. Set the "carpet/hard floor" selector to the

correct position for the type of floor, ZChapter 4.2, “Vacu-

um cleaning”, step 5.

The dust container is full.

Empty/clean the dust container, ZChapter 5.1, “Emptying

and cleaning the dust container”.

The filters are dirty. Clean the respective filter, ZChapter

5.2, “Cleaning central lamellae filter and motor protection

filter” or ZChapter 5.3, “Cleaning the exhaust filter”.

Nozzle, telescopic tube or suction hose is blocked.

Remove the obstacle. If necessary, use a long wooden

stick (e.g. a broomstick) to do this.

Problem Possible cause / solution

Centrino X3.1.book Seite 15 Dienstag, 16. November 2010 4:58 16

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dirt Devil M2012-2 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info