Bedienungsanleitung Dremel 1100 (Seite 4 von 68) (Englisch, Spanisch)

25103

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Wire and bristle brushes must never be operated at

speeds greater than 15,000/min. Direct the dis-

charge of the spinning wire brush away from you.

Small particles and tiny wire fragments may be dis-

charged at high velocity during the “cleaning” action

with these brushes and may become imbedded in

your skin. Bristles or wires will be discharged from

the brush at high speeds.

Wear protective gloves and face shield with wire or

bristle brushes. Apply wire or bristle brushes light-

ly to the work as only the tips of the wire/bristles do

the work. “Heavy” pressure on bristles will cause the

wire or bristle to become overstressed, resulting in a

wiping action and will cause the bristles/wire to be

discharged.

Carefully handle both the tool and individual grind-

ing wheels to avoid chipping or cracking. Install a

new wheel if tool is dropped while grinding. Do not

use a wheel that may be damaged. Fragments from

a wheel that bursts during operation will fly away at

great velocity possibly striking you or bystanders.

Never use dull or damaged bits. Sharp bits must be

handled with care. Damaged bits can snap during

use. Dull bits require more force to push the tool,

possibly causing the bit to break.

Use clamps to support workpiece whenever practi-

cal. Never hold a small workpiece in one hand and

the tool in the other hand while in use. Allow for

sufficient space, at least 6", between your hand and

the spinning bit. Round material such as dowel rods,

pipes or tubing have a tendency to roll while being

cut, and may cause the bit to “bite” or jump toward

you. Clamping a small workpiece allows you to use

both hands to control the tool.

Inspect your workpiece before cutting. When cutting

irregularly shaped workpieces, plan your work so it

will not slip and pinch the bit and be torn from your

hand. For example, if carving wood, make sure there

are no nails or foreign objects in the workpiece. Nails

or foreign objects can cause the bit to jump.

Never start the tool when the bit is engaged in the

material. The bit cutting edge may grab the material

causing loss of control of the cutter.

Avoid bouncing and snagging the wheel, especially

when working corners, sharp edges etc. This can

cause loss of control and kick-back.

The direction of feed with the bit into the material

when carving, routing or cutting is very important.

Always feed the bit into the material in the same

direction as the cutting edge is exiting from the

material (which is the same direction as the chips

are thrown). Feeding the tool in the wrong direction,

causes the cutting edge of the bit to climb out of the

work and pull the tool in the direction of this feed.

If the workpiece or bit becomes jammed or bogged

down, turn the tool “OFF” by the switch. Wait for

all moving parts to stop and unplug the tool, then

work to free the jammed material. If the switch to

the tool is left “ON” the tool could restart unexpected-

ly causing serious personal injury.

Do not leave a running tool unattended, turn power

off. Only when tool comes to a complete stop it is

safe to put it down.

Do not grind or sand near flammable materials.

Sparks from the wheel could ignite these materials.

Do not touch the bit or collet after use. After use the

bit and collet are too hot to be touched by bare hands.

Regularly clean the tool's air vents by compressed

air. Excessive accumulation of powdered metal inside

the motor housing may cause electrical failures.

Do not allow familiarity gained from frequent use of

your rotary tool to become commonplace. Always

remember that a careless fraction of a second is suf-

ficient to inflict severe injury.

Do not alter or misuse tool. Any alteration or modifi-

cation is a misuse and may result in serious personal

injury.

This product is not intended for use as a dental drill,

in human or veterinary medical applications.

Serious personal injury may result.

When using the steel saws, cutoff wheels, high

speed cutters or tungsten carbide cutters, always

have the work securely clamped. Never attempt to

hold the work with one hand while using any of

these accessories. The reason is that these wheels

will grab if they become slightly canted in the groove,

and can kickback causing loss of control resulting in

serious injury. Your second hand should be used to

steady and guide the hand holding the tool. When a

cutoff wheel grabs, the wheel itself usually breaks.

When the steel saw, high speed cutters or tungsten

carbide cutter grab, it may jump from the groove and

you could lose control of the tool.

Some dust created by power

sanding, sawing, grinding,

drilling, and other construction activities contains

chemicals known to cause cancer, birth defects or

other reproductive harm. Some examples of these

chemicals are:

• Lead from lead-based paints,

• Crystalline silica from bricks and cement and other

masonry products, and

• Arsenic and chromium from chemically treated

lumber.

Your risk from these exposures varies, depending on

how often you do this type of work. To reduce your

exposure to these chemicals: work in a well ventilated

area, and work with approved safety equipment, such

as those dust masks that are specially designed to fil-

ter out microscopic particles.

WARNING

Page 4

DM 2610930085 11-05 11/30/05 2:56 PM Page 4

Dremel 1100 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info