Bedienungsanleitung Dremel 1800 (Seite 3 von 76) (Englisch, Französisch, Spanisch)

32279

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Specific Safety Rules

Scroll Station Station

Always disconnect the power cord from the power

source before making any adjustments or attaching any

accessories. Always turn off saw before disconnecting it

to avoid accidental starting when reconnecting to a

power source.

You may unexpectedly cause the tool to start

leading to serious personal injury.

Never leave tool running unattended. Turn power off.

Don't leave tool until it comes to a complete stop.

Never leave the switches in "ON" position. Before plug-

ging the tool in, check that the switches are "OFF".

Accidental start-ups could cause injury.

Do not use tool if switch does not turn it on and off. Have

broken switches replaced by an authorized service center.

Use only Dremel Scroll Station blades. Use the right blade

size, style and cutting speed for the material and the type of

cut. Sharp blades minimize stalling and kickbacks. Blade

teeth should point down toward the table.

Avoid awkward operations and hand positions and

always make sure you have good balance.

A sudden slip

could cause your hand to move into the blade.

Firmly clamp or bolt your saw station to a stable, level

workbench or table.

The most comfortable table height is

approximately waist height.

Never stand on tool. Serious injury could occur if the tool is

tipped or if the blade is unintentionally contacted.

Before making a cut, be sure all adjustments are secure.

Loose table or guards could shift in use and cause you to

loose control of the workpiece.

Always adjust drop foot to just clear the workpiece.

Proper adjustment of the drop foot will help protect your fin

gers and keep blade breakage to a minimum.

Always support large workpieces while cutting to mini

mize risk of blade pinching and kickback.

Heavy work-

piece may cause the table to slip, walk or slide while cutting.

Be sure the blade path is free of nails. Inspect for and

remove nails from lumber or workpiece before cutting or

sanding.

Keep hands away from cutting area. Do not hand hold

pieces so small that your fingers go under the blade guard.

Do not reach underneath work or in blade cutting path with

your hands and fingers for any reason.

Never start the tool when the blade is in contact with the

workpiece. Allow the motor to come up to full speed

before starting a cut.

Blade in contact with the workpiece

on start up will cause it to jump.

Observe and follow correct direction of feed and do not

feed the material too quickly. Hold the work firmly

against the table.

Feed work into a blade against the teeth

of the blade. Feeding material too forcefully may cause blade

to snap.

Use caution when cutting materials with an irregular

cross-section or rounds like dowel rods. If possible lay

the material on its "flat" side when cutting. For round

stock use a "Vee" block to support the material.

Wavy

material like molding will tend to rock and may bind while cut-

ting. Rounds will tend to roll while being cut and the blade

may "bite" and grab it from your control.

Do not remove jammed cutoff pieces until blade has

stopped. Never touch blade or other moving parts dur-

ing use. Contacting the blade or other moving mechanism

may cause injury.

Power Take Off Safety Rules

The use of attachments and accessories not recom-

mended by Dremel may result in risk of injuries.

Remove the Scroll Station blade and replace it with the

Scroll Station blank in the blade holder before operating

any attachment from the power take off. Avoid the pos-

sibility of contacting the reciprocating blade while sand-

ing.

Inadvertent contact with a blade could cause serious

lacerations.

Unplug the tool before changing accessories or attach-

ments.

Accidental start-ups may occur if sander is plugged

in while changing an accessory.

Keep the cord to the side away from sanding pad or other

attachments.

The cord can be dragged into housing and

become entangled with the pad or other moving components.

Disc Sander Safety Rules

Use only 5" diameter adhesive backed sandpaper discs.

Do not use sandpaper intended for larger sanding pads.

Larger sandpaper will extend beyond the sanding pad caus-

ing snagging, tearing of the paper or kickback.

Make sure the sandpaper disc is not torn or loose before

turning tool on.

The disc could fly away unexpectedly.

Properly adjust sanding disc to avoid it overhanging the

pad.

Spinning sanding disc overhanging its pad can cause

severe lacerations.

Always position your workpiece on the downward side of

the direction of rotation arrow while sanding.

Hold the

work firmly against the table. Sanding on the upward side of

the rotation could cause the workpiece to lift up or kickback.

Refer to rotation arrow on your sander guard.

Avoid awkward hand positions while sanding. A sudden

slip could cause a hand to move into abrasive disc.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dremel 1800 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info