Bedienungsanleitung Dremel DSM20 (Seite 9 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch, Norwegisch, Finnisch)

488591

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

of moving parts, breakage of parts and any other

condition that may affect the power tools operation. If

damaged, have the power tool repaired before use. Many

accidents are caused by poorly maintained power tools.

f. Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to bind

and are easier to control.

g. Use the power tool, accessories and tool bits etc., in

accordance with these instructions, taking into account

the working conditions and the work to be performed.

Use of the power tool for operations different from those

intended could result in a hazardous situation.

BATTERY TOOL USE AND CARE

a. Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type of

battery pack may create a risk of fire when used with another

battery pack.

b. Use power tools only with specifically designated battery

packs. Use of any other battery packs may create a risk of

injury and fire.

c. When battery pack is not in use, keep it away from other

metal objects like paper clips, coins, keys, nails, screws,

or other small metal objects that can make a connection

from one terminal to another. Shorting the battery terminals

together may cause burns or a fire.

d. Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally occurs,

flush with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause

irritation or burns.

SERVICE

a. Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

MACHINE-SPECIFIC SAFETY

WARNINGS

CUT-OFF MACHINE SAFETY WARNINGS

a. The guard provided with the tool must be securely

attached to the power tool and positioned for maximum

safety, so the least amount of wheel is exposed towards

the operator. Position yourself and bystanders away from

the plane of the rotating wheel. The guard helps to protect

operator from broken wheel fragments and accidental contact

with wheel.

b. Use only bonded reinforced or diamond cut-off wheels

for your power tool. Just because an accessory can

be attached to your power tool, it does not assure safe

operation.

c. The rated speed of the accessory must be at least

equal to the maximum speed marked on the power tool.

Accessories running faster than their rated speed can break

and fly apart.

d. Wheels must be used only for recommended

applications. For example: do not grind with the side

of cut-off wheel. Abrasive cut-off wheels are intended for

peripheral grinding, side forces applied to these wheels may

cause them to shatter.

e. Always use undamaged wheel flanges that are of correct

diameter for your selected wheel. Proper wheel flanges

support the wheel thus reducing the possibility of wheel

breakage.

f. Do not use worn down reinforced wheels from larger

power tools. Wheels intended for a larger power tool are not

suitable for the higher speed of a smaller tool and may burst.

g. The outside diameter and the thickness of your

accessory must be within the capacity rating of your

power tool. Incorrectly sized accessories cannot be

adequately guarded or controlled.

h. The arbour size of wheels and flanges must properly fit

the spindle of the power tool. Wheels and flanges with

arbour holes that do not match the mounting hardware of the

power tool will run out of balance, vibrate excessively and

may cause loss of control.

i. Do not use damaged wheels. Before each use, inspect

the wheels for chips and cracks. If power tool or wheel

is dropped, inspect for damage or install an undamaged

wheel. After inspecting and installing the wheel, position

yourself and bystanders away from the plane of the

rotating wheel and run the power tool at maximum no

load speed for one minute. Damaged wheels will normally

break apart during this test time.

j. Wear personal protective equipment. Depending on

application, use face shield, safety goggles or safety

glasses. As appropriate, wear dust mask, hearing

protectors, gloves and shop apron capable of stopping

small abrasive or workpiece fragments. The eye protection

must be capable of stopping flying debris generated by

various operations. The dust mask or respirator must be

capable of filtrating particles generated by your operation.

Prolonged exposure to high intensity noise may cause

hearing loss.

k. Keep bystanders a safe distance away from work area.

Anyone entering the work area must wear personal

protective equipment. Fragments of workpiece or of

a broken wheel may fly away and cause injury beyond

immediate area of operation.

l. Hold the power tool by insulated gripping surfaces

only, when performing an operation where the cutting

accessory may contact hidden wiring or its own cord.

Cutting accessory contacting a “live” wire may make exposed

metal parts of the power tool “live” and could give the

operator an electric shock.

m. Position the cord clear of the spinning accessory. If you

lose control, the cord may be cut or snagged and your hand

or arm may be pulled into the spinning wheel.

n. Never lay the power tool down until the accessory has

come to a complete stop. The spinning wheel may grab the

surface and pull the power tool out of your control.

o. Do not run the power tool while carrying it at your side.

Accidental contact with the spinning accessory could snag

your clothing, pulling the accessory into your body.

p. Regularly clean the power tool’s air vents. The motor’s

Dremel DSM20 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info