Bedienungsanleitung Dremel DSM20 (Seite 11 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch, Norwegisch, Finnisch)

488591

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

sharp edges or bouncing have a tendency to snag the

rotating accessory and cause loss of control or kickback.

e. Do not attach a saw chain woodcarving blade or toothed

saw blade. Such blades create frequent kickback and loss

of control.

SAFETY WARNINGS SPECIFIC FOR GRINDING

AND ABRASIVE CUTTING-OFF OPERATIONS

a. Use only wheel types that are recommended for your

power tool and the specific guard designed for the

selected wheel. Wheels for which the power tool was not

designed cannot be adequately guarded and are unsafe.

b. The guard must be securely attached to the power tool

and positioned for maximum safety, so the least amount

of wheel is exposed towards the operator. The guard

helps to protect the operator from broken wheel fragments,

accidental contact with wheel and sparks that could ignite

clothing.

c. Wheels must be used only for recommended

applications. For example: do not grind with the side

of cut-off wheel. Abrasive cut-off wheels are intended for

peripheral grinding, side forces applied to these wheels may

cause them to shatter.

d. Always use undamaged wheel flanges that are of correct

size and shape for your selected wheel. Proper wheel

flanges support the wheel thus reducing the possibility of

wheel breakage. Flanges for cut-off wheels may be different

from grinding wheel flanges.

e. Do not use worn down wheels from larger power tools.

Wheel intended for larger power tool is not suitable for the

higher speed of a smaller tool and may burst.

ADDITIONAL SAFETY WARNINGS SPECIFIC

FOR ABRASIVE CUTTING-OFF OPERATIONS

a. Do not “jam” the cut-off wheel or apply excessive

pressure. Do not attempt to make an excessive depth

of cut. Overstressing the wheel increases the loading and

susceptibility to twisting or binding of the wheel in the cut and

the possibility of kickback or wheel breakage.

b. Do not position your body in line with and behind the

rotating wheel. When the wheel, at the point of operation,

is moving away from your body, the possible kickback may

propel the spinning wheel and the power tool directly at you.

c. When wheel is binding or when interrupting a cut for any

reason, switch off the power tool and hold the power tool

motionless until the wheel comes to a complete stop.

Never attempt to remove the cut-off wheel from the cut

while the wheel is in motion otherwise kickback may

occur. Investigate and take corrective action to eliminate the

cause of wheel binding.

d. Do not restart the cutting operation in the workpiece. Let

the wheel reach full speed and carefully re-enter the cut.

The wheel may bind, walk up or kickback if the power tool is

restarted in the workpiece.

e. Support panels or any oversized workpiece to minimize

the risk of wheel pinching and kickback. Large workpieces

tend to sag under their own weight. Supports must be placed

under the workpiece near the line of cut and near the edge of

the workpiece on both sides of the wheel.

f. Use extra caution when making a “pocket cut” into

existing walls or other blind areas. The protruding wheel

may cut gas or water pipes, electrical wiring or objects that

can cause kickback.

ENVIRONMENT

DISPOSAL

The machine, accessories and packaging should be sorted for

environmental-friendly recycling.

ONLY FOR EUROPEAN COUNTRIES

Do not dispose of power tools into household waste!

According the European Guideline 2002/96/EC for

Waste Electrical and Electronic Equipment and its

implementation into national right, power tools that are

no longer usable must be collected separately and

disposed of in an environmentally correct manner.

SPECIFICATIONS

GENERAL SPECIFICATIONS

Dremel DSM20 cut-off tool

DSM20

Voltage Rating 220-240V~50/60Hz

Wattage rating 710 W

No Load Speed no 17000 min–1

Max abrasive wheel diameter 77 mm type 1

Wheel arbor 11 mm

Max cutting depth 21.5 mm

EXTENSION CORDS

Use completely unrolled and safe extension cords with a capacity

of 5 Amps.

ASSEMBLY

WARNING

ALWAYS TURN OFF THE TOOL BEFORE

CHANGING ACCESSORIES, CHANGING

COLLETS, OR SERVICING THE TOOL AND REMOVE BATTERY

PACK.

GENERAL

This Dremel DSM20 tool is intended for straight cuts in wood,

plastic, metal, drywall, fiberboard, and tile using the applicable

accessories recommended by Dremel.

PICTURE 1

A. “Lock-on” button

B. Paddle switch with “lock-off” feature

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dremel DSM20 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info