Bedienungsanleitung Easypix PulseOximeter PO2 (Seite 2 von 2) (Englisch)

731580

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Measuring steps

Remove the battery compartment cover and insert the

batteries as shown in Figures 1.

Securely re-fit the battery compartment cover.

Squeeze one end of the device to open it and place an index

finger inside. Allow the device to gently close on the finger

as shown in Figure 2. (Index, middle or ring fingers can be

used for a reading)

Press the power / function button on the front panel to

switch on the device. Keep the finger and device still with as

little movement as possible and allow the device to take a

measurement.

Ensure the finger is inserted far enough into the sensor so

that the fingernail is just opposite to the light emitted

from the sensor.

Figure 1 Figure 2

Do not perform SpO² monitoring and NIBP (Non-invasive

blood pressure) measurements on the same arm

simultaneously. Obstruction of blood flow during NIBP

measurements may adversely affect the reading of the

SpO² value.

Do not use the Pulse Oximeter to measure patients whose

pulse rate is lower than 30bpm, as this may cause incorrect

results.

Ensure there is no contamination and/or scar on the tested

finger as the result indicated may be incorrect due to the

signal received by the sensor being affected.

When used on various patients, the product is prone to

cross contamination, which should be prevented and

controlled by the user. Disinfection is recommended before

using the product on other patients.

The highest temperature threshold of the sensor contacts

with a patient’s skin is 41°C.

Repeat use may require the use of different fingers to

obtain a measurement.

Factors affecting measurement accuracy

Incorrect placement of the finger may affect the accuracy of

the measurement.

The measurements also depend on absorption of a special

wavelength ray by oxidized hemoglobin and

deoxyhemoglobin. Concentration of nonfunctional

hemoglobin may affect the accuracy of the measurement.

Always consult a doctor if in doubt.

Shock, anemia, hypothermia and the application of

vasoconstriction drug may decrease arterial blood flow to

an unmeasurable level.

Pigment, or deep color (for example: nail polish, artificial

nails, dye or pigmented cream) may cause inaccurate

measurements.

Rotate the display

To ro ta t e t h e di s pl ay for c o nv en i en t r ea di n g, when the

result has been displayed on the screen, short press the

“POWER/FUNCTION” button once.

Auto switch off

The product will switch off automatically after 10 seconds

of no signal being detected.

Lanyard placement

1. Thread the thinner end of the lanyard through the hole.

2. Thread the thicker end of the lace through the threaded

end before pulling it tightly.

Cleaning and disinfection

Clean the product with cotton or damp soft cloth.

After cleaning, wipe dry and allow to full air dry.

Disinfection

The recommended disinfectants include: ethanol 70%,

isopropanol 70%, glutaraldehyde (2%) solution

disinfectants.

Clean the product as instructed above.

Disinfect the product with cotton or soft cloth moistened

with one of the recommended disinfectants.

After disinfection, be sure to wipe off the disinfectant left

on the product with a soft cloth moistened with water.

Allow the product to air dry.

Never immerse the device in liquid.

We recommend cleaning and disinfecting the product when

necessary or when used with different patients.

Never use cleaning agents/disinfectants other than those

recommended.

Never permit high-pressure and high-temperature

disinfection of the device.

Always switch off the device and remove the batteries

before cleaning or disinfecting.

Disposal

Dispose of packaging

For disposal, separate packaging into different types.

Cardboard and board must be disposed of as paper and foil

must be recycled.

Disposal of Waste Electrical and Electronic

Equipment and/or Battery by users in private households

in the European Union.

This symbol on the product or on the packaging indicates

that this cannot be disposed of as a household waste. You

must dispose of your waste equipment and/or battery by

handling it over to the applicable take-back scheme for the

recycling of electrical and electronic equipment and/or

battery. For more information about recycling of this

equipment and/or battery, please contact your city office,

the shop where you purchased the equipment or your

household waste disposal service. The recycling of materials

will help to conserve natural resources and ensure that it is

recycled in a manner that protects human health and

environment.

Declaration of conformity

For the product Pulse Oximeter PO2

We hereby confirm that it meets the basic requirements

laid down in Council Directive (1999/5/EC).

This declaration is based on the full compliance of that

product with the following European standards:

EN 55014-1:2017

EN 61000-3-2:2014

EN 61000-3-3:2013

EN 55014-2:2015

This explanation is given for the manufacturer / importer

easypix GmbH

Em Parkveedel 11

50733 Köln, Germany

The EC Declaration of Conformity can be downloaded here:

http://www.easypix.info/download/pdf/

doc_pulseoximeter_po2.pdf

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Easypix PulseOximeter PO2 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Easypix PulseOximeter PO2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info