Bedienungsanleitung Eberspacher Timer Modulator 701 serie (Seite 2 von 4) (Englisch)

701137

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

Instant Heat ON/OFF key

Adjustment Up key

Disengaged pre-set symbol

Ventilation symbol

Temperature ramp.

Current Time, Preset Time,

Heating Time, Run Time

and Diagnostics.

Day selected indicator boxes.

Clock symbol.

Heater operation symbol.

10.

Preset Programme

symbols.

11.

Adjustment Down key.

12.

Programme key.

13.

Set/Programme key.

Low Heat

High Heat

701 Series Timer / Modulator With Diagnostic Readout Instructions

Introduction

Your Timer/Modulator offers manual

and programmable control along with

temperature adjustment of your heater.

When the heater is switched on by the

Timer/Modulator in a programmed

mode it will run for 1 hour or for the

duration time that you have selected e.g

Heater on at 0700, duration time of 1 hour,

which means heater will be switched off

automatically at 0800.

lock Settings:-

Press and hold

key until the

symbol

begins to flash. Use the

and

keys to

set correct time. Press and release the

key and the day box will begin to flash.

Use the

and

keys to set the correct

day. Press and release the

key again to

reset the clock to the start of the minute

displayed. This may be used to coincide

with a known time signal.

Please Note:

These adjustments are not possible

when the heater is in operation. To set the

heater’s programmable switch on timer, see

“Setting Program Times”.

witching on the Heater

(Manually)

Press the

key and the

symbol will

appear on the display. The heater will

commence its startup cycle. The display

will change to show a default of one hour

heating countdown time. This can be

extended

in increments of 10 minutes,

30 minutes, 1 hour, 1 hour 30 minutes, 2

hours

up to eight hours or to continuous

running operation (shown as C-: -- on

display) by repeatedly pressing the

key

while the heater is in operation. Current

time will be displayed every 5 seconds.

Switching off the Heater

(Manually)

The heater may be switched off at any time

by pressing the

key. The cooling down

cycle will then be initiated.

Adjusting the Temperature

Pressing the

and

keys will alter the

20 segment temperature ramp shown on

the display. This level may be adjusted

at any time and will remain in the

timer memory when the heater is not in

operation.

Diagnostic Readout

With the heater switched on, press and

hold

key until the display shows

“dAtA”. Release key and display then

shows “AF--” and alternatively displays

the current fault code. Each press of

the

key will scroll through the last 5

previously stored fault codes.

Typical fault codes -

10 = Over voltage - Check battery charging system.

11 = Under voltage - Check battery voltage.

12 = Overheating - Check air ducts for obstruction.

52 = Safety time exceeded - Check fuel supply.

For other codes consult your local dealer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eberspacher Timer Modulator 701 serie Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info