Bedienungsanleitung Eberspacher Timer Modulator 701 serie (Seite 3 von 4) (Englisch)

701137

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

Press

and

keys together to erase

stored faults and display shows “EEEE”.

To exit diagnostic mode, press and release

the

key. If stored faults cannot be erased

consult your local dealer.

Heater Run Time

Press and hold the

key until the display

shows the heater run time in hours.

Setting Programme Times

Press the

key and the P1 symbol will

begin to flash. Pressing the

key will

alternate the display between a preset

time display and “OFF”. With P1 flashing

in the time display mode the desired

programme time can be set using the

and

keys.

Once the desired time has been selected

and if no keys are depressed for 8 seconds

the display will revert to the clock mode.

During this 8 second period pressing the

key will select P2 which can be used to

select another programme time or be set to

“OFF” if not required.

A further pressing of the

key will select

the P3 symbol which can be set or turned

off in the same manner as above.

Setting Programme Days

Having set programme times P1, P2 or

P3 or all three, press the

key, all the ‘P’

symbols that have been selected will start

flashing and a box will appear around

one of the days. Press the

key to select

“ON” if you require the selected day to be

programmed, or “OFF” if you do not wish

it to be selected.

To move onto the following day press

the

key once again and select “ON” or

“OFF” as before. Repeat this procedure for

all seven days. To store these settings in

the Timer / Modulator memory, wait for 8

seconds and the display will revert to the

clock mode.

Setting Programme Duration

To set the desired heater duration, press

and hold the

key and whilst holding

repeatedly press the

key to select the

desired time in increments of 10 minutes,

30 minutes, 1 hour, 1 hour 30 minutes, 2

hours up until 8 hours.

NOTE: Continuous operation is not

selectable in this programme mode.

Once stored the preset duration time

cannot be adjusted during heater “ON”

operation.

Switching on the Heater

(Programmed)

To activate your selected program settings,

press the

key to show the P1,P2,P3 (to

determine when the heater will switch on)

or symbol

to turn off all settings.

NOTE: If all presets and days have been

selected to “OFF” pressing the

key will

have no effect.

When the heater has been switched on

manually, it is possible to view which

of the programmed times have been

set and whether or not they have been

activated. Press the

key to view and if

any programmed time has been activated,

its corresponding

will flash. If no

programmed times have been activated

then

flashes. Press the

key to activate

or de-activate the programmed times

as required. Wait 8 seconds and the

display will revert to manual operation

countdown.

Ventilation

To activate Ventilation Mode, repeatedly

press

key until only one segment shows

in the ramp. Press and hold the

key

until

shows and display changes to

1 hour countdown. To stop ventilation,

press

key to return to normal display

time.

Please Note:

The ventilation countdown

time of 1 hour is not adjustable.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eberspacher Timer Modulator 701 serie Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info