Bedienungsanleitung Electronics Line EL-2762 (Seite 1 von 2) (Englisch)

580183

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Page 1

Wireless Gas Leak Detector

(Model EL-2762)

Introduction

Electronics Line Ltd's Wireless Gas Leak Detector detects

mixtures of air and combustible gases (Natural Gas, Methane,

Propane and Butane).

Upon detecting the presence of gas, the unit emits an alarm and

notifies the control panel.

The main features of your Wireless Gas Leak Detector include the

following:

 Integrated transmitter designed for use EL's wireless alarm

systems

 Easy to install

 Monitoring for Natural Gas, Methane, Propane and Butane in

a continuous manner

 Loud alarm (85 dB) when detecting a buildup of Gas

 Test button

 Self-test

Selecting the installation location

The Wireless Gas Leak Detector will function effectively if installed in the

correct location. Consider the following before mounting the gas alarm:

 Methane (Natural) Gas: Methane is lighter than air,

therefore the greatest concentration of gas is found right

below the ceiling, and therefore the Wireless Gas Leak

Detector should be installed on the wall, approximately 30

cm (12”) below the ceiling.

 Butane Gas: Propane and Butane are heavier than air,

therefore the greatest concentration of gas is found right

above the floor level. The Wireless Gas Leak Detector

should therefore be installed about 30cm (12”) above the

floor. Do not mount in a location where the gas alarm

could be damaged by dirt, liquids, etc.

Note:

Do not install the detector on the ceiling or on the floor.

Floor

Ceiling

30 cm (12")

Detector location for Methane (Natural) Gas detection

Detector location for Propane and Butane detection

 Install the detector in close proximity to every

gas-operated appliance.

Do not:

 Install the gas detector directly on any gas appliance.

 Install the gas detector in sealed or closed compartments or

in an area where a wall or a closed door can obstructs the

flow of gas to the gas alarm.

 Install the gas detector in locations where fans, open doors,

open windows etc. may prevent gas from reaching the

sensor.

 Install the gas detector in any room where aerosols or

ammonia are used (e.g. bathrooms).

To install the detector:

1. Remove the mounting bracket from your unit according to Fig. 1.

1 2 3

Fig. 1

2. Hold the Mounting bracket against the wall as a template and

mark the locations for the 2 mounting holes.

3. Using a 3/16-inch (5 mm) drill bit, drill two holes at the marks

and insert wall plugs (Fig. 2).

Fig. 2

4. Secure the mounting bracket to the wall.

5. Line up the side slot of the bracket and the detector. Push the

detector onto the mounting bracket and fix it (see arrow

direction, Fig. 2). Pull the detector outwards to make sure that it

is securely attached to the mounting bracket.

6. Connect the detector power cable to the wall power outlet.

Transmitter/Receiver Communication Setup

1. Set the panel to registration mode.

2. Insert the batteries into compartment. The detector enters

registration mode during which a transmission is sent every

few seconds. You can terminate registration mode by

pressing the Test Button. Test mode is automatically

terminated after approximately five minutes.

3. Verify that the detector has been identified by the receiver.

TEST/HUSH POWER SERVICE ALARM ALARM VENT

SENSOR VENT

Fig. 3

TESTING YOUR DETECTOR

To test the detector (do not test when detector is at warm up

mode), press the Test Button.

 The red and orange LED's will flash and a sound will be

heard

MUTING YOUR DETECTOR

You can partially mute the detector in an event of alarm by

pressing the Test Button. The Red LED will continue to flash and a

short beep will be heard every 16 seconds.

Formatiert: Schriftartfarbe:

Automatisch

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Electronics Line EL-2762 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Electronics Line EL-2762

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info