Bedienungsanleitung Elica Optica (Seite 12 von 12) (Englisch)

471168

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Maintenance

Prior to any maintenance operation ensure that the cooker

hood is disconnected from the power supply.

Cleaning: The cooker hood should be cleaned regularly

internally and externally.

For cleaning use a cloth moistened with denatured alcohol

or neutral liquid detergents. Avoid abrasive detergents.

Warning: Failure to carry out the basic standards of the

cleaning of the cooker hood and replacement of the filters

may cause fire risks.

Therefore we recommend observing these instructions.

Grease filter

This must be cleaned once a month (and, for the model with

electronic control panel, every time LED 4 starts to flash 

see preceding page) using non aggressive detergents,

either by hand or in the dishwasher, which must be set to

a low temperature and a short cycle. When washed in a

dishwasher, the grease filter may discolour slightly, but this

does not affect its filtering capacity. To remove the grease

filter, pull the spring release handle (f) - (Fig. 2).

Charcoal filter (filter version only)

It absorbs unpleasant odours caused by cooking.

The charcoal filter can be washed once every two months

(when using the hood 2,5 hours per day, in average and,

for the model with electronic control panel, every time LED

5 starts to flash  see preceding page) using hot water and

a suitable detergent, or in a dishwasher at 65°C (if the

dishwasher is used, select the full cycle function and leave

dishes out).

Eliminate excess water without damaging the filter, then

remove the mattress located inside the plastic frame and put

it in the oven for 10 minutes at 100° C to dry completely.

Replace the mattress every 3 years and when the cloth is

damaged.

Remove the filter holder frame by turning the knobs (g) 90°

that affix the chimney to the cooker hood (Fig. 3).

Insert the pad (i) of activated carbon into the frame (h) and

fit the whole back into its housing (j).

Replacing lamps

Warning!

Prior to touching the light bulbs ensure they are cooled down.

For models shown in Fig. 1E + Fig. 4E:

1. Press on the lamp cover and release to open.

2. Replace the damaged light bulb.

Only use halogen bulbs of 20W max (G4), making sure

you do not touch them with your hands.

3. Close the lamp cover (it will snap shut).

For models shown in Fig. 1N/O + Fig. 4N/O:

1. Unscrew the lamp cover.

2. Replace the damaged light bulb.

Only use halogen bulbs of 20W max (G4), making sure

you do not touch them with your hands.

3. Refit the lamp cover.

For models shown in Fig.1+Fig.4 (A/B/C/D/F/H/I/K/P/

Q):

1. Extract the lamp cover by levering it off with a small

screwdriver or similar tool.

2. Replace the damaged light bulb.

Only use halogen bulbs of 20W max (G4), making sure

you do not touch them with your hands.

3. Close the lamp cover (it will snap shut).

For models shown in Fig. 1J + Fig. 4J:

1. Use a small screwdriver as a lever on the borders of

the lamp in order to remove the lightbulb.

2. Unthread the connector a.

3. Slide out the lightbulb to be replaced and replace with a

new 12V 20W 30° Ø35 12V GU4 PHILIPS STANDARD

LINE code 425409.

4. Carry out the replacement and mount the new lightbulb

by following instructions in the reverse.

For models shown in Fig. 1G + Fig. 5G:

Dismount the chimneys: remove the two screws (20 a)

that attaches the upper chimney to the support G (Fig.

16).

Remove the box q: remove the screw r that

secures the cooker hood.

Remove the lamp housing s: remove the screws t

that position the housing in the lamp housing area.

Extract the damaged lamp.

Use only PHILIPS type 14515 (GX 5.3) 12V - 75W

halogen bulbs..

Reposition and secure the lamp housing s and the box

q and remount the chimneys.

For models shown in Fig. 1K + Fig. 4K:

Certain versions of this cooker hood provide for an

incandescent lamp at 40W maximum (E14), remove the

grease filter to access the lamp housing and carry out any

replacements.

Only for the illustrated model in Fig. 1L + Fig. 6L:

1. Open the front panel v upwards, which holds the lamp

in place, ensuring to hold the lamp z with one hand.

2. Replace the damaged lamp with one of identical technical

characteristics.

Attention! To guarantee the equivalent quality of

lighting, it is recommended to use the same type of lamp

bulb:

Philips neon Lamp bulb 13W Code Ref. 8711500644305.

Ensure that the transparent part of the lamp bulb is facing

inwards so as to guarantee correct light distribution.

3. Replacing the starter:

Use a starter with identical technical characteristics.

Recommended starter: Use a Philips S10 starter.

4. Remount the lamp housing and the front panel in the

inverse in relation to the dismounting.

Only for the models illustrated in Fig. 1M + Fig. 7M:

1. Remove the grease filters.

2. Remove the ceiling light unscrewing the 3 screws that

fix it to the hood (hold the ceiling light to prevent it falling).

3. Change the damaged bulb with one with identical

technical characteristics.

Changing the starter

Use a starter with identical technical characteristics.

Starter advised: use a Phillips S10 starter.

4. Remount the ceiling light and the grease filters in the

reverse manner to the montage.

If the lights do not work, make sure that the lamps are

fitted properly into their housings before you call for

technical assistance.

Caution

This appliance is designed to be operated by adults. Children

should not be allowed to tamper with the controls or play with

the appliance.

Do not use the cooker hood where the grill is not correctly

fixed! The suctioned air must not be conveyed in the same

channel used for fumes discharged by appliances powered

by other than electricity. The environment must always be

adequately aerated when the cooker hood and other

appliances powered by other than electricity are used at the

same time. Flambé cooking with a cooker hood is

prohibited. The use of a free flame is damaging to the filters

and may cause fire accidents, therefore free flame cooking

must be avoided. Frying of foods must be kept under close

control in order to avoid overheated oil catching fire. Carry

out fumes discharging in accordance with the regulations in

force by local laws for safety and technical restrictions.

Elica Optica Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info