Bedienungsanleitung Elica Pro-Europa (Seite 7 von 9) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

471236

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

Instruction on mounting and use

Consult the designs in the front pages referenced in the text

by alphabet letters.

Closely follow the instructions set out in this manual. All

responsibility, for any eventual inconveniences, damages or

fires caused by not complying with the instructions in this

manual, is declined.

Use

Ducting version

The hood is equipped with a top air outlet B for discharge of

fumes to the outside (exhaust pipe and pipe fixing clamps not

provided).

Installation

The minimum distance between the supporting surface for the

cooking vessels on the hob and the lowest part of the range

hood must be not less than 50cm from electric cookers and

65cm from gas or mixed cookers.If the instructions for

installation for the gas hob specify a greater distance, this

must be adhered to.

Electrical connection

The electrical tension must correspond to the tension noted on

the label placed inside the cooker hood. Connect the electrical

plug, where provided, to the an easily accessible outlet in

conformity with local standards in force. Where an electrical

plug is not provided (for direct connection to electrical

network) or is not easily accessible, place a standards

approved bipolar switch that provide full disconnection under

overvoltage category III conditions, in accordance with the

wiring rules.

Attention: substituting the supply cable must be carried out

by the authorised technical assistance service.

Mounting

Fig.1

• Pull handle F and remove the fat filters (1)

Note: the number of fat filters can vary on the basis of

the dimensions of the hood.

• Remove the screws that fix the upper covers (the 900mm

model has 1 cover, models with larger widths are

supplied with 2 covers, right and left) (2).

Note: the screws to remove are in the positions indicated

by the arrow in 1.1 and 1.2 (only 900mm width model).

• Remove the mantle(s) (3)

• Fix connection ring B with 4 screws (4).

Note: Apply, if envisaged and/or necessary for your

installation, the reduction to the B connection ring.

Without the reduction, Ø 200mm tubes are to be used;

with the reduction Ø 150mm tubes can be used.

Fig. 2

• Place the hole diagram on the wall (5)

• Fix the 2 brackets to the wall using 2 screws and 2

dowels (6)

• Hang the hood on the brackets (7)

• Adjust the distance (8) and horizontal setup (9) of the

hood, acting on the apposite screws.

• Mark the holes for the definitive fixing (10) from inside

and, where envisaged, from outside the hood.

Note: See the diagram of the back of the hood with the

position of the definite fixing holes/dowels/screws. (Fig.

2,1)

• Remove the hood. (11)

• Make the holes and insert the dowels at the points

previously marked. (12)

• Assemble the bracket for the flue and fix it with the 4

screws supplied. (13)

Note: The extension of the bracket must be identical to

the internal width of the flue.

Fix the bracket to the wall with 2 dowels and 2 screws

(14)

• Hang the hood on the brackets again. (15)

• Fix the hood definitively. (16)

Note: consult montage operations 10-12 for the number

and position of the definitive fixing screws.

Fig. 3

• Apply a discharge tube (to purchase) to the connection

ring. (17)

• Connect the electricity. (18)

• Fix the upper flue with 2 screws (19A) to the bracket

(19B)

• Lower the lower section of the flue (20) and fix it onto the

upper side of the hood with 2 screws (21 - Fig. 3.1).

Fig. 4

• Reposition the cover/s over the hood and fix it/them from

inside the hood (22).

Note: the screws must be inserted into the positions

indicated by the arrow in figure 4.1 and (4.2 - only

900mm width model).

• Mount the fat filters again.

Operation

Use the high suction speed in cases of concentrated kitchen

vapours. It is recommended that the cooker hood suction is

switched on for 5 minutes prior to cooking and to leave in

operation during cooking and for another 15 minutes

approximately after terminating cooking.

The hood is fitted with a control panel with aspiration speed

selection control and a light switch to control cooking area

lights.

Maintenance

Before performing any maintenance operation, isolate the

hood from the electrical supply by switching off at the

connector and removing the connector fuse.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elica Pro-Europa Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info