Bedienungsanleitung Elro HA68S (Seite 32 von 34) (Englisch)

536725

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

To change the setting press .

Press to enable the Auto Report function, or

Press to disable the Auto Report function.

JAMMING DETECTION

This feature controls the Control Panels RF jamming detection circuitry, which if

enabled, will continuously scan for radio jamming signals on the system

operating frequency.

Default setting: OFF

Scroll through the menu until ‘2-5 RF Jamming’ is displayed. The current

setting will also be displayed.

To change the setting press .

Press to enable Jamming Detection, or

Press to disable Jamming Detection.

CONTROL PANEL BACK LIGHT

This controls the time period that the backlight for the Control Panel display will

stay illuminated for after the last key is pressed.

Default setting: 10s

Scroll through the menu until ‘2-6 Back Light’ is displayed. The current setting

will also be displayed.

To change the setting pres s .

Scroll through available options, (10, 20, 30 and 60s) until the required setting

is displayed.

Press to save and exit, or

Press to exit without saving.

WARNING BEEP

When any abnormal conditions have occurred such as the system being

triggered or detectors’ low battery, the ‘ALARM MEM’ LED on the Control Panel

will be on accompanying warning beep as a reminder. This feature, if enabled,

allows the Control Panel to be emitted a warning beep periodically once

abnormal conditions is occurred.

If when the system is disarmed the ‘ALARM MEM’ LED is flashing and the Control

Panel beeps periodically, this indicates that an alarm has occurred. To cancel

the LED and stop the beeping you must access the event log or press to

eliminate the flashing ‘ALARM MEM’ LED and the beeping as well.

-35--30-

PROGRAM MODE

Code:

3. ZONE SETUP:

3-1 Set 1-36

Zone

Input (01-36)

Zone Number

:1 Learning ID

Learning

Intruder

24 hour Intruder

Fire

Medical help

Panic

Learning OK

Time Out

ID Duplicate

:2 Zone Name

xxxxxxxxxxxxxx

:3 Zone Type

xxxxxxxxxxxxxx

:4 Zxx Chime

Mode xxxx

:5 Zxx ENTRY

DELAY: XXX XXX

:6 Zxx

PARTIAL ARM 1:

:7 Zxx

PARTIAL ARM 2:

:8 Magnetic

O/C Detector xxx

:9 Auto Report

:10 Zone Status

:11 Zone Reset

:12 Zone Siren

Select

ON->* OFF->#

Select

ON->* OFF->#

Select

ON->* OFF->#

Select

ON->* OFF->#

Select

ON->* OFF->#

Select

ON->* OFF->#

Select

ON->* OFF->#

Input

(01-25)*10Sec.

Select

ON->* OFF->#

Select

ON->* OFF->#

No name

Front door

Back door

Patio door

Dining room

Living room

Lounge

Kitchen

Shed

Garage

Hall

Landing

Upstairs

Downstairs

Bedroom 1

Bedroom 2

Bedroom 3

Bedroom 4

Windows 1

Windows 2

Windows 3

PIR Detector

Magnetic Contact

FIRE/SMOKE

Panic/PA

Medical

ZONE SETUP

Scroll through the programming menu until ‘3. ZONE SETUP’ is displayed and

press .

Enter the zone number to be configured and press .

The following configuration options are based upon configuring zone 1. Options

for all other zones (2-36) are identical except the zone number reference will

change according to the zone being configured.

ENEN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elro HA68S Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elro HA68S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info