Bedienungsanleitung Emtec H510 (Seite 4 von 74) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

473755

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

Setup

Battery Installation

1. On the back of the remote, push down on the tab and lift the cover off.

2. Match the batteries to the + and - marks inside the battery case, then insert 4 AAA Alkaline

batteries.

3. Press the battery cover back into place.

Make sure you use new batteries. You can have problems with learning codes if your

batteries are old.

Battery Saver

Your remote automatically turns off if the keys are depressed for more than 30 seconds. This

will save your batteries should your remote get stuck in a place where the keys remain

depressed (e.g., between the sofa cushions). Also, the screen turns off a short time after no

keys have been pressed for a while (or a short time after a key has been stuck for 30 seconds).

The duration before the screen turns off can be adjusted from about 2 seconds to about 35

seconds, from the Setup, Advanced, Options menu, see page 18

Permanent Memory

All the devices you set up, their codes, punchthrough settings, and all your favourites, etc.,

are stored in permanent memory while you are changing batteries so you will not lose any

codes or settings stored in the remote while you are changing batteries.

Using the Wizard

After you insert the batteries the Language screen (1) appears. Choose

the language you want by pressing on the side key next to the choosen

language.

The Setup Wizard screen (2) appears. You can exit the Wizard at any

time by pressing the HOME key (located just below the screen). Press

any key at screen (2) to continue and follow the instructions on the

screens.

Pressing OK at screen (3) takes you to the next screen (4). Pressing

the Left navigation key (Back key) on the remote at screen (4) takes

you to screen (5) that has 10 yellow arrows. This is an exception to

the rule because we’re teaching you how to use the remote. But

pressing Back again at this point does take you “back.”

(2)

(3)

(4)

(5)

(1)

Try pressing the Back key a few times to go back through the Wizard

and then follow the instructions on the screens again to familiarize

yourself with how to step through the screens and go back. You can

go back and forth through the Wizard but once you’ve set up your

devices and quit to save the settings, you won’t see the Wizard again

unless you do a Master Reset.

To do a Master Reset: Press the HOME key, then select Setup,

then select Advanced, then select Clear Settings, then select Master

Clear. Note this will erase everything you have set up in the remote.

Pressing any of the 10 Side Keys (K1 thru K10) at screen (5)

takes you to the screen where you set up your first device (TV).

See next page.

Setting Up Your Devices

How to set up a TV

After you’ve been through the Wizard for the first time, the screen

(1) shown to the right appears. This is the start of the Wizard to set

up your devices (TV being the first one). Manually turn on the

device(s) to be set up (TV, VCR, etc.).

If you know your brand of TV, select Yes which results in a faster

search for your TV’s code. (Selecting No searches the complete

library of TV codes, rather than just the codes for your brand of

TV).

Pressing the Side Key next to Yes at screen (1) takes you to a screen

(2) where the most common brands are shown next to the Side Keys.

If your brand isn’t shown you can press the Side Key adjacent to

Next to show more brands, (shown alphabetically) or press the Side

Key adjacent to Back to go back to the previous screen of brands.

Note, on the very first screen of brands, the Side Key adjacent to

Back takes you to the last screen of brands (so you can go back

through the list instead of forward through it if you prefer). In this

case we selected Sony.

Screen (3) tells you to point the remote directly at your TV and

repeatedly press (but not hold) Power (or Chan Up/Down, or Play

for VCRs etc.) until your device responds. Pressing Power sends

the Power command to your TV and screen (4) shows that you’ve

selected code 1 of xx (xx will vary by brand). Keep pressing Power

until your TV responds and then press Save.

(1)

(2)

(3)

(4)

K10

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Emtec H510 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info