Zoom out
Zoom in
Vorherige Seite
1/149
Nächste Seite
User’s Guide
1

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Inhalt der Seiten


  • Page 1

    User’s Guide



  • Page 2

    Notations Used in This Guide
    • Safety indications
    The documentation and the projector use graphical symbols to show how to use the projector safely.
    Please understand and respect these caution symbols in order to avoid injury to persons or property.

    Warning

    This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.

    Caution

    This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.

    • General information indications

    Attention

    a

    Indicates procedures which may result in damage or injury if sufficient care is not taken.
    Indicates additional information and points which may be useful to know regarding a topic.

    s

    Indicates a page where detailed information regarding a topic can be found.

    g

    Indicates that an explanation of the underlined word or words in front of this symbol appears in the glossary of terms. See the "Glossary"
    section of the "Appendix".
    s "Glossary" p.128

    [Name]
    Menu Name

    Indicates the name of the buttons on the remote control or the control panel.
    Example: [Esc] button
    Indicates Configuration menu items.
    Example:
    Select Brightness from Image.
    Image - Brightness



  • Page 3

    Contents

    3

    Notations Used in This Guide . . . . . . . . . . . . . . . . . . . . . . . . 2

    Screen Size and Approximate Projection Distance . . . . . . . . . . . . . . . . . . . . . . . 20

    Connecting Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
    Connecting a Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
    Connecting Image Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
    Connecting USB Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

    Introduction
    Projector Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
    List of Functions by Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Quick and Easy Set up, Projection, and Storage . . . . . . . . . . . . . . . . . . . . . . . . .
    Connecting with a USB cable and projecting (USB Display) . . . . . . . . . . . . . . .
    Easy Image Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Adjusting the projected image to automatically fit into the screen frame - Screen
    Fit - (EB-1775W only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Detecting projector movements and automatically correcting image distortion
    ........................................................
    Useful Functions for Expanding the Scope of Your Presentations . . . . . . . . . . . . .
    Increasing projection content in wide (WXGA) screen (EB-1775W/EB-1770W/
    EB-1760W only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Connecting to a wireless LAN and projecting images from the computer's screen
    (EB-1775W/EB-1770W/EB-1760W only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Connecting a projector and a computer wirelessly with Quick Wireless Connection
    (EB-1775W/EB-1770W/EB-1760W only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Making the most of the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . .

    .
    .
    .
    .

    8
    8
    8
    8

    . 8
    . 9
    . 9
    . 9
    . 9
    . 9
    . 9

    Part Names and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
    Front/Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Replacing the remote control batteries . . . . . . . . . . . . . . . . . . . . .
    Remote control operating range . . . . . . . . . . . . . . . . . . . . . . . . .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    10
    11
    12
    13
    14
    17
    17

    Preparing the Projector
    Installing the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
    Installation Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
    Installation methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

    Basic Usage
    Projecting Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
    From Installation to Projection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Automatically Detect Input Signals and Change the Projected Image (Source Search)
    ... ....... ......... ... ....... ......... ... ....... ..........
    Switching to the Target Image by Remote Control . . . . . . . . . . . . . . . . . . . . . . .
    Projecting with USB Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Connecting for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Uninstalling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

    26
    27
    28
    28
    28
    29
    30

    Adjusting Projected Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
    Automatically Adjust to Fit the Screen Frame - Screen Fit - (EB-1775W only) . . .
    Correcting Keystone Distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Correcting automatically - Auto H/V-Keystone - (EB-1775W only) . . . . . . . .
    Correcting automatically - Auto V-Keystone - (EB-1770W/EB-1760W/EB-1750
    only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Correcting manually - manual H/V-Keystone - . . . . . . . . . . . . . . . . . . . . .
    Correcting manually - Quick Corner - . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Adjusting the Image Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Adjusting the Image Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Adjusting the Horizontal Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Correcting the Focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Selecting the Projection Quality (Selecting Color Mode) . . . . . . . . . . . . . . . .
    Setting Auto Iris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Changing the Aspect Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Changing methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Changing the aspect ratio for video equipment images . . . . . . . . . . . . . . .

    . . . 31
    . . . 33
    . . . 33
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .

    34
    34
    34
    36
    37
    37
    37
    38
    38
    39
    40
    40
    40



  • Page 4

    Contents

    4

    Changing the aspect ratio for computer images . . . . . . . . . . . . . . . . . . . . . . . 42

    Configuration Menu
    Using the Configuration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

    Useful Functions

    List of Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
    Projection Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
    Projecting Without a Computer (Slideshow) . . . . . . . . . . . . . . . . . . . . . . . . . .
    Specifications for files that can be projected using Slideshow . . . . . . . . . . . . .
    Slideshow examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Slideshow operating methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Projecting the selected image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Projecting image files in a folder in sequence (Slideshow) . . . . . . . . . . . . . . .
    Playing a scenario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Operating procedures during scenario playback . . . . . . . . . . . . . . . . . . . . .
    Image file display settings and Slideshow operation settings . . . . . . . . . . . . .
    Hiding the Image and Sound Temporarily (A/V Mute) . . . . . . . . . . . . . . . . . . . .
    Freezing the Image (Freeze) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Pointer Function (Pointer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Enlarging Part of the Image (E-Zoom) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Using the Remote Control to Operate the Mouse Pointer (Wireless Mouse) . . . . .
    Setting the ID and Using the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . .
    Setting the Projector ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Setting the remote control ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Correcting Color when Projecting from Multiple Projectors . . . . . . . . . . . . . . . .
    Summary of correction procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Correcting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Saving a User's Logo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .

    45
    45
    45
    46
    48
    49
    49
    49
    50
    51
    52
    52
    53
    54
    56
    57
    57
    58
    58
    58
    60

    Security Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
    Managing Users (Password Protect) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Kinds of Password Protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Setting Password Protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Entering the Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Restricting Operation (Control Panel Lock) . . . . . . . . . . . . . . . . . . . . . . .
    Anti-Theft Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .

    62
    62
    62
    63
    64
    65

    Configuration Menu Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Network menu (EB-1775W/EB-1770W/EB-1760W only) . . . . . . . . . . . .
    Image Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Signal Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Settings Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Extended Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Network Menu (EB-1775W/EB-1770W/EB-1760W Only) . . . . . . . . . . . . . .
    Notes on operating the Network menu . . . . . . . . . . . . . . . . . . . . . . .
    Soft keyboard operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Basic menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Wireless LAN menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Security menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Mail menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Others menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Reset menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Info Menu (Display Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Reset Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .

    68
    69
    70
    71
    73
    74
    76
    76
    77
    78
    79
    80
    82
    82
    83
    84
    84

    Troubleshooting
    Using the Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
    Problem Solving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
    Reading the Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    When the Indicators Provide No Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Problems Relating to Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    No images appear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Moving images are not displayed (only the moving image portion turns black)
    ...... .. ..... ...... ..... .. ...... ..... ....... ...... ....
    Projection stops automatically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    The message "Not supported" is displayed . . . . . . . . . . . . . . . . . . . . . . . .
    The message "No Signal" is displayed . . . . . . . . . . . . . . . . . . . . . . . . . . . .

    .
    .
    .
    .

    .
    .
    .
    .

    88
    91
    92
    92

    .
    .
    .
    .

    .
    .
    .
    .

    93
    93
    93
    93



  • Page 5

    Contents

    Images are fuzzy, out of focus, or distorted . . . . . . . . . . . . . . . . . . . . . . . .
    Interference or distortion appear in images . . . . . . . . . . . . . . . . . . . . . . . .
    The image is truncated (large) or small, or the aspect is not suitable . . . . . . .
    Image colors are not right . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Images appear dark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Problems when Projection Starts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    The projector does not turn on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Other Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    No sound can be heard or the sound is faint . . . . . . . . . . . . . . . . . . . . . . .
    The remote control does not work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    I want to change the language for messages and menus . . . . . . . . . . . . . . .
    Email is not received even if a problem occurs in the projector (EB-1775W/
    EB-1770W/EB-1760W only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

    5

    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .
    .
    .
    .
    .

    94
    95
    95
    96
    97
    97
    97
    98
    98
    98
    99

    . . 99

    Maintenance
    Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
    Cleaning the Projector's Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
    Cleaning the Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
    Cleaning the Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

    Replacing Consumables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
    Replacing the Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Lamp replacement period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    How to replace the lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Resetting the lamp hours . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Replacing the Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Air filter replacement period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    How to replace the air filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

    103
    103
    104
    106
    106
    106
    106

    Appendix

    Optional Accessories and Consumables . . . . . . . . . . . . . . . . . . . . 110
    Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
    Consumables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110

    Monitoring and Controlling (EB-1775W/EB-1770W/EB-1760W
    Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
    Changing Settings Using a Web Browser (Web Control) . . . . . . . . . . . . . . . . . . .
    Projector setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Displaying the Web Control screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Displaying the Web Remote screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Using the Mail Notification Function to Report Problems . . . . . . . . . . . . . . . . . .
    Reading Error Notification Mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Management Using SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    ESC/VP21 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Before starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Command list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Communications protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

    111
    111
    111
    111
    113
    113
    113
    114
    114
    114
    114

    About Event ID (EB-1775W/EB-1770W/EB-1760W Only) . . . . . . 116
    About PJLink (EB-1775W/EB-1770W/EB-1760W Only) . . . . . . . . 117
    Screen Size and Projection Distance . . . . . . . . . . . . . . . . . . . . . . . . 118
    Projection Distance (For EB-1775W/EB-1770W/EB-1760W) . . . . . . . . . . . . . . . . . 118
    Projection Distance (For EB-1750) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119

    Supported Monitor Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
    Supported Resolutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Computer signals (analog RGB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Component video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Composite video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Input signal from the HDMI port (EB-1775W/EB-1770W/EB-1760W only) . . .

    .
    .
    .
    .
    .

    .
    .
    .
    .
    .

    121
    121
    121
    121
    121

    Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
    Projector General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

    Useful Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
    EasyMP Network Projection(EB-1775W/EB-1770W/EB-1760W only) . . . . . . . . . . . 109
    EasyMP Slide Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
    EasyMP Monitor(EB-1775W/EB-1770W/EB-1760W only) . . . . . . . . . . . . . . . . . . . 109



  • Page 6

    Contents

    Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
    Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
    General Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
    About Notations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
    General Notice: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130

    Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147

    6



  • Page 7

    Introduction
    This chapter explains the projector's features and the part names.



  • Page 8

    Projector Features

    8

    • Make easy height adjustments with one lever.
    • No cool down delay makes it easy to put away.

    List of Functions by Model
    Available functions differ depending on the model being used. See the table
    below for a list of the functions available for each model.
    Function

    EB-1775W

    EB-1770W

    EB-1760W

    USB Display
    HDMI Connection

    -

    Screen Fit

    -

    -

    -

    Auto H/V-Keystone

    -

    -

    -

    Auto V-Keystone
    Wireless LAN
    Connection

    By simply connecting the supplied USB cable,
    you can project images from a computer's screen
    without a computer cable.
    s "Projecting with USB Display" p.28

    USB

    *1

    *1

    WXGA Resolutions
    Quick Wireless
    Connection

    Connecting with a USB cable and projecting (USB Display)

    EB-1750

    *2

    *2

    Network Menu

    -

    Easy Image Correction

    -

    Adjusting the projected image to automatically fit into the screen
    frame - Screen Fit - (EB-1775W only)

    -

    Slideshow
    *1 The Wireless LAN unit is available as an option.
    *2 The Quick Wireless Connection USB Key is available as an option.

    Quick and Easy Set up, Projection, and Storage
    • The portable, lightweight design allows you to easily make presentations
    away from your office.
    • Turn the projector on and off by simply plugging in or unplugging.
    • Project onto large screens from a short distance.

    By pressing the [Screen Fit] button, you can automatically adjust the
    projected image to fit into the screen frame by correcting any image
    distortion.
    s "Automatically Adjust to Fit the Screen Frame - Screen Fit - (EB-1775W
    only)" p.31



  • Page 9

    Projector Features

    9

    Detecting projector movements and automatically correcting
    image distortion
    This projector automatically corrects keystone distortion and focus
    problems which occur when positioning or moving the projector.
    For EB-1775W
    Automatically corrects vertical and horizontal keystone distortion.

    Connecting to a wireless LAN and projecting images from the
    computer's screen (EB-1775W/EB-1770W/EB-1760W only)
    By using EasyMP Network Projection and the
    supplied or optional Wireless LAN unit, you can
    wirelessly project the computer's screen.
    s EasyMP Network Projection Operation
    Guide

    s "Correcting automatically - Auto H/V-Keystone - (EB-1775W only)"

    p.33
    For EB-1770W/EB-1760W/EB-1750
    Automatically corrects vertical keystone distortion.
    s "Correcting automatically - Auto V-Keystone - (EB-1770W/EB-1760W/

    EB-1750 only)" p.34

    Useful Functions for Expanding the Scope of Your
    Presentations

    Connecting a projector and a computer wirelessly with Quick
    Wireless Connection (EB-1775W/EB-1770W/EB-1760W only)
    By simply connecting the supplied or optional
    Quick Wireless Connection USB Key to a
    computer, you can connect the projector and
    the computer using the wireless communication
    and project images from the computer.

    USB

    Increasing projection content in wide (WXGA) screen (EB-1775W/
    EB-1770W/EB-1760W only)
    By increasing the volume of images and text that
    you can display, you can improve the impact of
    your presentation.
    s "Changing the Aspect Ratio" p.40

    4:3(XGA)

    16:10(WXGA)

    Making the most of the remote control
    You can use the remote control to perform operations such as enlarging
    part of the image. You can also use the remote control as a pointer during
    presentations or as a mouse for the computer.
    s "Pointer Function (Pointer)" p.52
    s "Enlarging Part of the Image (E-Zoom)" p.53
    s "Using the Remote Control to Operate the Mouse Pointer (Wireless

    Mouse)" p.54



  • Page 10

    Part Names and Functions

    10

    All of the features in this guide are explained using illustrations of
    EB-1775W unless otherwise mentioned.

    Front/Top
    EB-1770W
    EB-1760W
    EB-1750

    Name

    A Air exhaust vent

    Function
    Exhaust vent for air used to cool the projector internally.

    Name

    B Wireless LAN indicator
    (EB-1775W/EB-1770W/
    EB-1760W only)

    Displays the access status of the supplied or optional
    Wireless LAN unit.

    C Wireless LAN unit
    cover
    (EB-1775W/EB-1770W/
    EB-1760W only)

    When making a wireless connection between the
    projector and computer, remove this cover to install the
    supplied or optional Wireless LAN unit.

    D A/V mute slide knob

    Slide the knob to open and close the A/V mute slide.

    E Foot adjust lever

    Press the foot lever to extend and retract the front foot.
    s "Adjusting the Image Position" p.37

    F Front adjustable foot

    When setup on a surface such as a desk, extend the foot to
    adjust the position of the image.
    s "Adjusting the Image Position" p.37

    G A/V mute slide

    Close when not using the projector to protect the lens. By
    closing during projection you can hide the image and the
    sound.
    s "Hiding the Image and Sound Temporarily (A/V
    Mute)" p.51

    H Remote receiver

    Receives signals from the remote control.

    I Sensor
    (EB-1775W only)

    Takes measurements when the projector automatically
    corrects the projected image.

    J Air intake vent
    (air filter)

    Takes in air to cool the projector internally.
    s "Cleaning the Air Filter" p.101

    K Speaker

    Plays back audio.

    L Indicators

    Indicates the projector's status.
    s "Reading the Indicators" p.88

    M Zoom ring

    Adjusts the image size.
    s "Adjusting the Image Size" p.36

    N Focus ring
    (EB-1770W/EB-1760W/
    EB-1750 only)

    Adjusts the image focus.
    s "Correcting the Focus" p.37

    Caution
    While projecting, do not put your face or hands
    near the air exhaust vent, and do not place objects
    that may become warped or damaged by heat near
    the vent.

    Function



  • Page 11

    Part Names and Functions

    Name

    11

    Function

    O Control panel

    Operates the projector.
    s "Control Panel" p.13

    P Lamp cover

    Open when replacing the projector's lamp.
    s "Replacing the Lamp" p.103

    Rear

    Name

    Function

    A Power inlet

    Connects the power cable to the projector.
    s "From Installation to Projection" p.26

    B Video port

    Inputs composite video signals from video sources.

    C Computer port

    Inputs image signals from a computer and component
    video signals from other video sources.

    D USB (TypeB) port

    • Connects the projector to a computer via the supplied
    USB cable, and the image on the computer is projected.
    s "Projecting with USB Display" p.28
    • Connects the projector to a computer via the supplied
    USB cable to use the Wireless Mouse function.
    s "Using the Remote Control to Operate the
    Mouse Pointer (Wireless Mouse)" p.54

    E USB (Type A) port

    • Connects a USB memory or digital camera to project
    data converted by EasyMP Slide Converter (.FSE
    and .SIT). The data is projected using Slideshow.
    s "Projecting Without a Computer (Slideshow)"
    p.45
    • Connects the optional Document Camera (ELPDC06).

    F HDMI port
    (EB-1775W/EB-1770W/
    EB-1760W only)

    Inputs video signals from HDMI compatible video
    equipment and computers. This projector is compatible
    with HDCPg.
    s "Connecting Equipment" p.21



  • Page 12

    Part Names and Functions

    Name

    12

    Function

    G Audio port

    Connects an audio cable to output audio from the
    projector's speakers.

    H Remote receiver

    Receives signals from the remote control.
    s "Remote control operating range" p.17

    I Lamp Cover Fixing
    Screw

    Screw to fix the lamp cover in place.

    J Security slot

    The security slot is compatible with the Microsaver
    Security System manufactured by Kensington.
    s "Anti-Theft Lock" p.65

    Base

    Name

    Function

    A Ceiling mount fixing
    points (three points)

    Attach the optional attachment plate here when
    suspending the projector from a ceiling.
    s "Installing the Projector" p.19
    s "Optional Accessories" p.110

    B Rear feet

    When setup on a surface such as a desk, turn to extend and
    retract to adjust the horizontal tilt.
    s "Adjusting the Horizontal Tilt" p.37



  • Page 13

    Part Names and Functions

    13

    Name

    Function

    C Front adjustable foot

    When setup on a surface such as a desk, extend the foot to
    adjust the position of the image.
    s "Adjusting the Image Position" p.37

    D Screw hole for the
    wireless LAN unit
    cover
    (EB-1775W/EB-1770W/
    EB-1760W only)

    Screw hole to fix the wireless LAN unit cover.

    Control Panel

    Name

    Function

    A [t] button

    Turns the projector power on or off.
    s "From Installation to Projection" p.26

    B [Screen Fit] button
    (EB-1775W only)

    Adjusts the projected image so that it fits the screen frame.
    s "Automatically Adjust to Fit the Screen Frame - Screen
    Fit - (EB-1775W only)" p.31
    This button is disabled when the projector is suspended
    from a ceiling.

    C [Source Search]
    button

    Changes to the next input source that is sending an image.
    s "Automatically Detect Input Signals and Change the
    Projected Image (Source Search)" p.27

    D [Enter] button

    • When the Configuration menu or the Help screen is
    displayed, it accepts and enters the current selection and
    moves to the next level.
    • If pressed during projection of computer signal images,
    it automatically adjusts the Tracking, Sync., and
    Position to project the optimum image.



  • Page 14

    Part Names and Functions

    Name

    14

    Function

    E [w][v] buttons

    • Performs vertical keystone correction.
    s "Correcting keystone distortion in vertical
    directions" p.34
    • If pressed when the Configuration menu or the Help
    screen is displayed, these buttons select menu items and
    setting values.
    s "Using the Configuration Menu" p.67
    s "Using the Help" p.87

    F [Help] button

    Displays and closes the Help screen which shows you how
    to deal with problems if they occur.
    s "Using the Help" p.87

    G [Esc] button

    • Stops the current function.
    • If pressed when the Configuration menu is displayed, it
    moves to the previous menu level.
    s "Using the Configuration Menu" p.67

    H [<][>] buttons

    • Performs horizontal keystone correction.
    s "Correcting keystone distortion in horizontal
    directions" p.34
    • If pressed when the Configuration menu or the Help
    screen is displayed, these buttons select menu items and
    setting values.
    s "Using the Configuration Menu" p.67
    s "Using the Help" p.87

    I [Menu] button

    Displays and closes the Configuration menu.
    s "Using the Configuration Menu" p.67

    J [Focus] button
    (EB-1775W only)

    Adjusts the image focus.
    s "Correcting the Focus" p.37

    Remote Control



  • Page 15

    Part Names and Functions

    Name

    15

    Function

    A [t] button

    Turns the projector power on or off.
    s "From Installation to Projection" p.26

    B [Computer] button

    Changes to images from the Computer port.

    C [Video] button

    Each time you press the button, the input source changes
    between images from the Video port and the HDMI port
    (EB-1775W/EB-1770W/EB-1760W only).

    D [Screen Fit] button

    Adjusts the projected image so that it fits the screen frame.
    (EB-1775W only)
    s "Automatically Adjust to Fit the Screen Frame - Screen
    Fit - (EB-1775W only)" p.31
    When the projector is suspended from a ceiling or when
    using EB-1770W/EB-1760W/EB-1750, this does not
    function even if the button is pressed.

    E Numeric buttons

    • Use this button to enter passwords and set the remote
    control ID.
    s "Setting the remote control ID" p.57
    s "Setting Password Protect" p.62
    • Use this button to enter numbers in Network settings
    from the Configuration menu. (EB-1775W/EB-1770W/
    EB-1760W only)

    F [A/V Mute] button

    Turns the video and audio on or off.
    s "Hiding the Image and Sound Temporarily (A/V
    Mute)" p.51

    G [Freeze] button

    Images are paused or unpaused.
    s "Freezing the Image (Freeze)" p.52

    H [Auto] button

    If pressed during projection of computer signal images, it
    automatically adjusts the Tracking, Sync., and Position to
    project the optimum image.

    I [Aspect] button

    The aspect ratio changes each time the button is pressed.
    s "Changing the Aspect Ratio" p.40

    Name

    Function

    J [Page] buttons
    [Up] [Down]

    Changes pages in files such as PowerPoint files when using
    the following projection methods.
    • When using the Wireless Mouse function
    s "Using the Remote Control to Operate the
    Mouse Pointer (Wireless Mouse)" p.54
    • When using USB Display
    s "Projecting with USB Display" p.28
    • During a network connection (EB-1775W/EB-1770W/
    EB-1760W only)
    When projecting images or scenarios using Slideshow,
    pressing these buttons displays the previous/next screen.

    K [E-Zoom] buttons
    [z][x]

    Enlarges or reduces the image without changing the
    projection size.
    s "Enlarging Part of the Image (E-Zoom)" p.53

    L [Menu] button

    Displays and closes the Configuration menu.
    s "Using the Configuration Menu" p.67

    M [
    [

    ][
    ][

    ] buttons

    ]

    • When the Configuration menu or the Help screen is
    displayed, pressing these buttons selects menu items
    and setting values.
    s "Using the Configuration Menu" p.67
    • When projecting a Slideshow, pressing these buttons
    displays the previous/next image, rotates the image, and
    so on.
    s "Slideshow operating methods" p.46
    • During Wireless Mouse function, the mouse pointer
    moves in the direction of the button that was pushed.
    s "Using the Remote Control to Operate the
    Mouse Pointer (Wireless Mouse)" p.54



  • Page 16

    Part Names and Functions

    Name

    16

    Function

    N [Enter] button

    • When the Configuration menu or the Help screen is
    displayed, it accepts and enters the current selection and
    moves to the next level.
    s "Using the Configuration Menu" p.67
    • Acts as a mouse's left button when using the Wireless
    Mouse function.
    s "Using the Remote Control to Operate the
    Mouse Pointer (Wireless Mouse)" p.54

    O [Esc] button

    • Stops the current function.
    • If pressed when the Configuration menu is displayed, it
    moves to the previous level.
    s "Using the Configuration Menu" p.67
    • Acts as a mouse's right button when using the Wireless
    Mouse function.
    s "Using the Remote Control to Operate the
    Mouse Pointer (Wireless Mouse)" p.54

    P [Volume] buttons
    [a][b]

    [a] Decreases the volume.
    [b] Increases the volume.
    s "Adjusting the Volume" p.38

    Q [Help] button

    Displays and closes the Help screen which shows you how
    to deal with problems if they occur.
    s "Using the Help" p.87

    R [Pointer] button

    Displays the on-screen pointer.
    s "Pointer Function (Pointer)" p.52

    S [Num] button

    Hold down this button and press the numeric buttons to
    enter passwords and numbers.
    s "Setting Password Protect" p.62

    T [Color Mode] button

    Each time the button is pressed, the Color Mode changes.
    s "Selecting the Projection Quality (Selecting Color
    Mode)" p.38

    U [ID] button

    Hold down this button and press the numeric buttons to
    set the remote control ID.
    s "Setting the remote control ID" p.57

    Name

    Function

    V [User] button

    Select any frequently used item from the five available
    Configuration menu items, and assign it to this button. By
    pressing the [User] button, the assigned menu item
    selection/adjustment screen is displayed, allowing you to
    make one-touch settings/adjustments.
    s "Settings Menu" p.73
    Power Consumption is assigned as the default setting.

    W [Focus] buttons
    [l][r]

    Adjusts the image focus. (EB-1775W only)
    When using EB-1770W/EB-1760W/EB-1750, this does
    not function even if the button is pressed.
    s "Correcting the Focus" p.37

    X [LAN] button

    Changes to the image projected with EasyMP Network
    Projection. When projecting using the supplied or
    optional Quick Wireless Connection USB Key, this button
    switches to that image. (EB-1775W/EB-1770W/
    EB-1760W only)

    Y [USB] button

    Each time the button is pressed, it cycles through the
    following images:
    • USB Display
    • Images from the device connected to the USB (TypeA)
    port

    Z [Source Search]
    button

    Changes to the next input source that is sending an image.
    s "Automatically Detect Input Signals and Change the
    Projected Image (Source Search)" p.27

    a Remote control lightemitting area

    Outputs remote control signals.



  • Page 17

    Part Names and Functions

    17

    Replacing the remote control batteries
    If delays in the responsiveness of the remote control occur or if it does not
    operate after it has been used for some time, it probably means that the
    batteries are becoming flat. When this happens, replace them with new
    batteries. Have two AA size manganese or alkaline batteries ready. You
    cannot use other batteries except for the AA size manganese or alkaline.

    Caution
    Check the positions of the (+) and (-) marks inside the battery holder to
    ensure the batteries are inserted the correct way.

    c

    Replace the battery cover.
    Press the battery compartment cover until it clicks into place.

    Attention
    Make sure you read the following manual before handling the batteries.
    s Safety Instructions

    a

    Remove the battery cover.
    While pushing the battery compartment cover catch, lift the cover
    up.

    Remote control operating range

    b

    Replace the old batteries with new batteries.



  • Page 18

    Preparing the Projector
    This chapter explains how to install the projector and connect projection sources.



  • Page 19

    Installing the Projector

    19

    Installation Methods

    Warning

    The projector supports the following four different projection methods.
    Install the projector according to the conditions of the installation location.
    • Project images from in front of
    the screen. (Front projection)

    • Project images from behind a
    translucent screen. (Rear projec‐
    tion)

    • Suspend the projector from the
    ceiling and project images from
    in front of a screen. (Front/Ceil‐
    ing projection)

    • Suspend the projector from the
    ceiling and project images from
    behind a translucent screen.
    (Rear/Ceiling projection)

    • A special method of installation is required when suspending the projector
    from a ceiling (ceiling mount). If it is not installed correctly, it could fall
    causing an accident and injury.
    • If you use adhesives on the Ceiling mount fixing points to prevent the screws
    from loosening, or if you use things such as lubricants or oils on the
    projector, the projector case may crack causing it to fall from its ceiling
    mount. This could cause serious injury to anyone under the ceiling mount
    and could damage the projector.
    When installing or adjusting the ceiling mount, do not use adhesives to
    prevent the screws from loosening and do not use oils or lubricants and so
    on.

    Attention
    • Do not use the projector on its side. This may cause malfunctions to occur.
    • Do not cover the projector's air intake vent or air exhaust vent. If either of
    the vents are covered, the internal temperature could rise and cause a fire.

    a

    • An optional ceiling mount and attachment plate are required when
    suspending the projector from a ceiling.
    s "Optional Accessories" p.110
    • You can change the setting as follows by pressing down the [A/V
    Mute] button on the remote control for about five seconds.
    FrontWFront/Ceiling
    Set Rear or Rear/Ceiling from the Configuration menu.
    s Extended - Projection p.74

    Installation methods
    Install the projector so that it is parallel to the screen.



  • Page 20

    Installing the Projector

    If the projector is installed at an angle to the screen, keystone distortion
    occurs in the projected image. See the following for more information on
    correcting keystone distortion.

    20

    For EB-1775W/EB-1770W/EB-1760W
    16:10 Screen Size

    s "Automatically Adjust to Fit the Screen Frame - Screen Fit - (EB-1775W

    only)" p.31

    150”
    (320×200cm)

    s "Correcting Keystone Distortion" p.33
    100”

    (220×130cm)

    80”

    (170×110cm)

    50”

    (110×67cm)

    a

    5m

    Place the projector on a level surface. See the following if the projected
    image is tilted horizontally.
    s "Adjusting the Horizontal Tilt" p.37

    For EB-1750
    4:3 Screen Size

    Screen Size and Approximate Projection Distance
    Projection size is determined by the distance from the projector to the
    screen. See the illustrations on the right to select the best position according
    to the screen size. The illustrations show the approximate shortest distance
    at maximum zoom. See the following for more information on the
    projection distance.

    150”
    100”
    80”
    50”

    s "Screen Size and Projection Distance" p.118

    a

    When you correct keystone distortion, the projected image may be
    reduced.

    5m



  • Page 21

    Connecting Equipment

    21

    This section gives examples of how to connect the projector and the projection source. Illustrations in this section are of EB-1775W/EB-1770W/EB-1760W.
    The port name, location, and connector orientation differ depending on the source being connected.

    Connecting a Computer
    To project images from a computer, connect the computer using one of the following methods.
    A When using the supplied computer cable
    Connect the computer's display output port to the projector's Computer input port using the supplied computer cable. To output audio from the projector's speaker, you need to
    connect a commercially available audio cable.
    B When using the supplied USB cable
    Connect the computer's USB port to the projector's USB (Type B) port using the supplied USB cable.
    C When using a commercially available HDMI cable
    Connect the computer's HDMI port to the projector's HDMI port using a commercially available HDMI cable.

    a

    Simply by connecting the projector to a computer via a USB cable, you can project images from the computer. This function is called USB Display.
    s "Projecting with USB Display" p.28



  • Page 22

    Connecting Equipment

    22

    Connecting Image Sources
    To project images from DVD players or VHS video and so on, connect to the projector using one of the following methods.
    A When using a commercially available video cable
    Connect the video output port on the image source to the projector's Video input port using a commercially available video cable. To output audio from the projector's speaker, you
    need to connect a commercially available audio cable.
    B When using the optional component video cable
    s "Optional Accessories" p.110
    Connect the component output port on the image source to the projector's Computer input port using the optional component video cable. To output audio from the projector's
    speaker, you need to connect a commercially available audio cable.
    When
    using a commercially available HDMI cable
    C
    Connect the HDMI port on the image source to the projector's HDMI port using a commercially available HDMI cable.

    Attention
    • If the input source is on when you connect it to the projector, it could cause a malfunction.
    • If the orientation or shape of the plug differs, do not try to force it in. The device could be damaged or could malfunction.

    a

    • If the source you want to connect to has an unusually shaped port, use the cable supplied with the device or an optional cable to connect to the projector.
    • When using a commercially available 2RCA(L/R)/stereo mini-pin audio cable, make sure it is labeled "No resistance".



  • Page 23

    Connecting Equipment

    23

    Connecting USB Devices
    You can connect devices such as USB memory, the optional Document Camera, and USB compatible hard disks and digital cameras.
    Using the USB cable supplied with the USB device, connect the USB device to the USB (Type A) port on the projector.

    USB
    Type A

    When the USB device is connected, you can project image files on the USB memory or digital camera using Slideshow.
    s "Slideshow examples" p.45

    If the Document Camera is connected while another image source is projecting, press the [USB] button on the remote control, or the [Source Search] button on
    the control panel to switch to images from the Document Camera.
    s "Automatically Detect Input Signals and Change the Projected Image (Source Search)" p.27

    Attention





    If you use a USB hub, the connection may not operate correctly. Devices such as digital cameras and USB devices should be connected to the projector directly.
    When connecting and using a USB-compatible hard disk, make sure you connect the AC adaptor supplied with the hard disk.
    Connect a digital camera or hard disk to the projector using a USB cable supplied with or specified for use with the device.
    Use a USB cable less than 3 m in length. If the cable exceeds 3 m, Slideshow may not function correctly.



  • Page 24

    Connecting Equipment

    24

    Removing USB devices
    After finishing projecting, remove USB devices from the projector. For devices such as digital cameras or hard disks, turn off the device and then remove it from
    the projector.



  • Page 25

    Basic Usage
    This chapter explains how to project and adjust images.



  • Page 26

    Projecting Images
    From Installation to Projection
    This section explains the procedure for connecting the projector to a
    computer with the computer cable and projecting images.

    26

    a

    The method for changing differs depending on the computer
    being used. See the documentation supplied with the computer.

    If the image is not projected, you can change the projected image using one
    of the following methods.
    • Press the [Source Search] button on the control panel or the remote
    control.
    s "Automatically Detect Input Signals and Change the Projected Image
    (Source Search)" p.27
    • Press the button for the target port on the remote control.
    s "Switching to the Target Image by Remote Control" p.28

    a

    After projecting the image, adjust the image if necessary.
    s "Automatically Adjust to Fit the Screen Frame - Screen Fit (EB-1775W only)" p.31
    s "Correcting Keystone Distortion" p.33
    s "Correcting the Focus" p.37

    a
    b
    c
    d
    e
    f

    Connect the projector to an electrical outlet with the power cable.
    Connect the projector to the computer with the computer cable.
    Turn on the projector.
    Slide open the A/V mute slide.
    Turn on your computer.
    Change the computer's screen output.
    When using a laptop computer, you need to change the screen
    output from the computer.
    Hold down the Fn key (function key), and press the b key.



  • Page 27

    Projecting Images

    27

    Automatically Detect Input Signals and Change
    the Projected Image (Source Search)
    Press the [Source Search] button to project images from the port currently
    receiving an image.
    Because only images from ports receiving an image are projected, you can
    quickly project the image you want.
    Using the remote control

    Using the control panel

    F LAN (EB-1775W/EB-1770W/EB-1760W only)

    When two or more image sources are connected, press the [Source Search]
    button until the target image is projected.
    When your video equipment is connected, start playback before beginning
    this operation.

    a

    The following screen is displayed when only the image that the
    projector is currently displaying is available, or when no image signal
    can be found. You can select the port where the equipment you want
    to use is connected. If no operation is performed after about 10
    seconds, the screen closes.
    Example: EB-1775W/EB-1770W/EB-1760W

    A
    B
    C
    D
    E

    Computer
    Video
    HDMI (EB-1775W/EB-1770W/EB-1760W only)
    USB Display
    USB



  • Page 28

    Projecting Images

    28

    Switching to the Target Image by Remote Control
    You can change directly to the target image by pressing the following
    buttons on the remote control.
    Remote control

    Projecting with USB Display
    You can use the supplied USB cable to connect the projector to a computer
    to project images from the computer.
    To start USB Display, set USB Type B to USB Display from the
    Configuration menu.
    s Extended - USB Type B p.74

    System Requirements
    For Windows

    A Changes to images from the Computer port.
    B Each time the button is pressed, it cycles through the following images:
    • Video port
    • HDMI port (EB-1775W/EB-1770W/EB-1760W only)
    C Each time the button is pressed, it cycles through the following images:
    • USB Display
    • Images from the device connected to the USB (TypeA) port
    D Changes to the image projected with EasyMP Network Projection. When
    projecting using the supplied or optional Quick Wireless Connection USB
    Key, this button switches to that image. (EB-1775W/EB-1770W/EB-1760W
    only)

    OS

    Windows 2000 Service Pack 4
    The following 32 bit operating systems:
    Windows XP
    Windows XP Service Pack 2 or later
    Windows Vista
    Windows Vista Service Pack 1 or later
    Windows 7

    CPU

    Mobile Pentium III 1.2 GHz or faster
    Recommended: Pentium M 1.6 GHz or faster

    Amount of
    Memory

    256 MB or more
    Recommended: 512 MB or more

    Hard Disk
    Free space

    20 MB or more

    Display

    Resolution of no less than 640x480 and no higher than
    1600x1200.
    Display color in 16-bit color or greater



  • Page 29

    Projecting Images

    29

    Connecting for the first time

    For Mac OS

    OS

    Mac OS X 10.5.1 or later
    Mac OS X 10.6.x

    CPU

    Power PC G4 1GHz or faster
    Recommended: Core Duo 1.83GHz or faster

    Amount of
    Memory

    512 MB or more

    Hard Disk
    Free Space

    20 MB or more

    Display

    Resolution of no less than 640x480 and no higher than
    1680x1200.
    Display color in 16-bit color or greater

    The first time you connect the projector and the computer using the USB
    cable, the driver needs to be installed. The procedure is different for
    Windows and Mac OS.

    a

    • You do not need to install the driver the next time you connect.
    • When inputting images from multiple sources, change the input
    source to USB Display.

    For Windows

    a

    Driver installation starts automatically.

    b
    c

    When the License Agreement screen is displayed, click Agree.

    d

    Disconnect the USB cable when you are finished.

    When you are using Windows 2000, double-click Computer EPSON_PJ_UD - EMP_UDSE.EXE on your computer.

    Computer images are projected.
    It may take a while before computer images are projected. Until
    computer images are projected, leave the equipment as it is and do
    not disconnect the USB cable or turn off the power to the projector.
    When disconnecting the USB cable, there is no need to use Safely
    Remove Hardware.



  • Page 30

    Projecting Images

    a

    • If it is not installed automatically, double-click My Computer
    - EPSON_PJ_UD - EMP_UDSE.EXE on your computer.
    • If nothing is projected for some reason, click All Programs EPSON Projector - EPSON USB Display - EPSON USB
    Display Vx.xx on your computer.
    • When using a computer running Windows 2000 under user
    authority, a Windows error message is displayed and you may
    not be able to use the software. In this case, try updating
    Windows to the latest version, restart, and then try to connect
    again.
    For more details, contact your local dealer or the nearest
    address provided in the following document.
    s Epson Projector Contact List

    30

    a

    • If the USB Display setup folder is not displayed automatically
    in the Finder, double-click EPSON PJ_UD - USB Display
    Installer on your computer.
    • If nothing is projected for some reason, click the USB
    Display icon in the Dock.
    • If there is no USB Display icon in the Dock, start USB
    Display from the Applications folder.
    • If you select Exit from the USB Display icon menu on the
    Dock, USB Display does not start automatically when you
    connect the USB cable.

    Uninstalling
    For Windows

    For Mac OS

    a
    b
    c
    d

    The Setup folder of USB Display is displayed in the Finder.

    Click Control Panel - Add/Remove Programs and uninstall EPSON USB
    Display.

    Double-click the USB Display Installer icon.

    For Mac OS

    Follow the on-screen instructions to install.

    Double-click Applications and then USB Display. Start USB Display
    UnInstaller in the Tool folder.

    When the License Agreement screen is displayed, click Agree.
    Enter the administrator authority password and start the installation.
    When the installation is complete, the USB Display icon is displayed
    in the Dock and menu bar.

    e

    Computer images are projected.

    f

    Select Disconnect from the USB Display icon menu on the menu
    bar or Dock, and then remove the USB cable.

    It may take a while before computer images are projected. Until
    computer images are projected, leave the equipment as it is and do
    not disconnect the USB cable or turn off the power to the projector.



  • Page 31

    Adjusting Projected Images
    Automatically Adjust to Fit the Screen Frame Screen Fit - (EB-1775W only)
    Screen Fit is a function that corrects the projected image so that it aligns
    with the frame (outer border) of the screen, white board, and so on. By
    pressing the [Screen Fit] button on the remote control or the control panel,
    the projected image is adjusted to fit the screen, and keystone correction
    and focus adjustments are performed automatically.

    The following conditions are necessary to correct the projected image using
    Screen Fit.
    Screen size: less than or equal to 100"
    Distance between projector and screen: approx. 1.0 to 2.5 m
    Correction angle: approx 20˚ right and left/approx. 30˚ up and down

    31

    a
    a

    • If you exceed the above mentioned range, the projected image
    cannot be corrected properly. Correct the projected image manually.
    • Screen Fit does not function if the projector is suspended from a
    ceiling. Correct the projected image manually.

    Press the [Screen Fit] button on the remote control or the control
    panel during projection.
    Using the remote control

    Using the control panel



  • Page 32

    Adjusting Projected Images

    b

    32

    Adjust the zoom ring so that the yellow frame is bigger than the
    screen frame as shown below. Position the black message box in
    the center of the screen.

    a
    d

    Once the adjustment screen appears, do not move the projector
    or block the image. The projected image will not be corrected
    properly.

    After the correction is performed, the following message appears.
    To exit the correction menu, press the [Esc] button on the remote
    control or the control panel to clear the message.
    To fine-tune the projected image after it has been corrected, make
    the adjustments using the [

    ][

    ][

    ][

    ] buttons on the

    control panel.

    If the yellow frame is still within the screen frame even after
    adjusting the zoom ring to its maximum size, try moving the
    projector further away from the screen.

    c

    Press the [Screen Fit] button or the [Enter] button.

    If no operation is performed, the message closes after about 7
    seconds.

    After the adjustment screen appears, the projected image is corrected
    according to the aspect ratiog of the image being input.

    After executing Screen Fit, Keystone from the Configuration menu is
    set to Quick Corner. After this, any correction of the projected
    image using the [

    ][

    ][

    ][

    ] buttons on the control panel is

    performed using the Quick Corner function.
    s "Correcting manually - Quick Corner -" p.34



  • Page 33

    Adjusting Projected Images

    a

    • Screen Fit corrects the projected image when it
    detects two or more sides inside the projected area,
    and aligns with the detected frame. For example,
    when projecting onto a wide screen in a small room,
    you can make corrections by fitting the top and
    bottom sides of the screen into the projected area.

    • Screen Fit may not work well in dark environments,
    such as a room with lights turned off. In this case,
    make the room brighter, and then try executing
    Screen Fit again.
    • Because Screen Fit uses a sensor, it may not work
    properly depending on the condition of the
    projection surface (deflections, patterns, and so on)
    or the effects of outside light. In this case, make the
    adjustments manually.
    s "Correcting manually - manual H/V-Keystone -"
    p.34

    Correcting Keystone Distortion
    You can correct keystone distortion using one of the following methods.
    • Correcting automatically
    Automatically correct keystone distortion.
    -Auto H/V-Keystone (EB-1775W only)
    -Auto V-Keystone (EB-1770W/EB-1760W/EB-1750 only)

    33

    • Correcting manually (manual H/V-Keystone)
    Manually correct distortion in the horizontal and vertical directions
    independently.

    • Correcting manually (Quick Corner)
    Manually correct the four corners independently.

    a

    When you correct keystone distortion, the projected image may be
    reduced.

    Correcting automatically - Auto H/V-Keystone - (EB-1775W only)
    When the projector detects any movement, for example when it is installed,
    moved, repositioned, or tilted, it automatically corrects vertical and
    horizontal keystone distortion. This function is called Auto H/VKeystone.



  • Page 34

    Adjusting Projected Images

    34

    When the projector remains still for about two seconds after it detects
    movement, it displays a screen for adjustment and then automatically
    corrects the projected image.

    a

    • Auto H/V-Keystone only works when Projection is set to Front
    from the Configuration menu.
    s Extended - Projection p.74
    • If you do not want to use the Auto H/V-Keystone function, set Auto
    H/V-Keystone to Off.
    s Settings - Keystone - H/V-Keystone - Auto H/V-Keystone
    p.73

    Correcting automatically - Auto V-Keystone - (EB-1770W/
    EB-1760W/EB-1750 only)

    Correcting keystone distortion in horizontal directions

    Press the [

    ][

    ] buttons on the control panel.

    When using EB-1770W/EB-1760W/EB-1750, only the vertical direction is
    corrected automatically. If you need to correct the horizontal direction, use
    manual H/V-Keystone.

    Correcting manually - manual H/V-Keystone Manually correct distortion in the horizontal and vertical directions
    independently. H/V-Keystone correction is ideal for fine-tuning keystone
    distortion.
    Correcting keystone distortion in vertical directions

    Press the [

    ][

    ] buttons on the control panel.

    a

    You can set manual H/V-Keystone from the Configuration menu.
    s Settings - Keystone - H/V-Keystone p.73

    Correcting manually - Quick Corner This allows you to manually correct each of the four corners of the
    projected image separately.



  • Page 35

    Adjusting Projected Images

    a

    Press the [Menu] button while projecting.
    s "Using the Configuration Menu" p.67
    Using the remote control

    b

    35

    Using the control panel

    Select Keystone from Settings.

    d

    Using the [

    ], [

    remote control, or the [

    ], [
    ], [

    ], and [
    ], [

    ] buttons on the

    ], and [

    ] buttons on the

    control panel, select the corner to correct, and then press
    the [Enter] button.

    c

    Select Quick Corner, and then press the [Enter] button.



  • Page 36

    Adjusting Projected Images

    e

    Using the [

    ], [

    remote control, or the [

    36

    ], [
    ], [

    ], and [
    ], [

    ] buttons on the

    ], and [

    ] buttons on the

    control panel, correct the position of the corner.
    If the triangle in the direction you are adjusting the shape turns gray,
    as shown in the screenshot below, you cannot adjust the shape any
    further in that direction.

    a

    • When Auto H/V-Keystone is set to On, the message "Do you
    want to perform Auto H/V-Keystone correction?" is displayed
    when the projector is moved. (EB-1775W only)
    After you perform this function, the Keystone setting changes
    from Quick Corner to H/V-Keystone, after which pressing
    the [

    ], [

    ], [

    ], and [

    ] buttons on the control

    panel performs H/V-Keystone.
    s Settings - Keystone - H/V-Keystone p.73
    • If the [Esc] button is held down for about two seconds while
    correcting with Quick Corner, the following screen is
    displayed.

    f

    Repeat procedures 4 and 5 as needed to adjust any remaining
    corners.

    g

    When you are done, press the [Esc] button to exit the correction
    menu.
    Because Keystone was changed to Quick Corner, the corner
    selection screen from step 3 is displayed when you press the [
    [

    ], [

    ], and [

    ],

    ] buttons on the control panel next time.

    [

    ] buttons on the control panel.

    s Settings - Keystone - H/V-Keystone p.73

    ], [

    ], [

    Adjusting the Image Size
    Turn the zoom ring to adjust the size of the projected image.

    Change Keystone to H/V-Keystone if you want to perform
    horizontal and vertical correction using the [

    Reset Quick Corner: Resets the result of Quick Corner
    corrections.
    Switch to H/V-Keystone: Switches the correction method to
    H/V-Keystone.
    s "Settings Menu" p.73

    ], and



  • Page 37

    Adjusting Projected Images

    T

    37

    Adjusting the Horizontal Tilt

    W

    Extend and retract the rear feet to adjust the projector's horizontal tilt.

    T

    W

    W

    T

    A Extend the rear foot.
    B Retract the rear foot.

    Adjusting the Image Position
    Press the foot lever to extend and retract the front foot. You can adjust the
    position of the image by tilting the projector up to 14 degrees.

    Correcting the Focus
    You can correct the focus using one of the following methods.
    • Press the [Focus] button on the control panel or the remote control to
    adjust the focus. (EB-1775W only)

    a

    The larger the angle of tilt, the harder it becomes to focus. Install the
    projector so that it only needs to be tilted at a small angle.



  • Page 38

    Adjusting Projected Images

    • Turn the focus ring to adjust the focus. (EB-1770W/EB-1760W/EB-1750
    only)

    38

    • Adjust the volume from the Configuration menu.
    s Settings - Volume p.73

    Caution
    Do not start at high volume.
    A sudden excessive volume may cause loss of hearing. Always lower the volume
    before powering off, so that you can power on and then gradually increase the
    volume.

    Selecting the Projection Quality (Selecting Color
    Mode)
    You can easily obtain the optimum image quality simply by selecting the
    setting that best corresponds to your surroundings when projecting. The
    brightness of the image varies depending on the mode selected.

    Adjusting the Volume
    You can adjust the volume using one of the following methods.
    • Press the [Volume] buttons on the remote control to adjust the volume.

    Mode
    Dynamic

    Ideal for use in a bright room. This is the brightest
    mode, and reproduces shadow tones well.

    Presentation

    Ideal for making presentations using color materials
    in a bright room.

    Theatre

    Ideal for watching films in a dark room. Gives
    images a natural tone.

    Photo*1

    Ideal for projecting still pictures, such as photos, in
    a bright room. The images are vivid and brought
    into contrast.

    Sports *2

    Ideal for watching TV programmes in a bright
    room. The images are vivid and brought to life.

    sRGB

    Ideal for images that conform to the sRGBg color
    standard.

    Remote control
    [a] Decreases the volume.
    [b] Increases the volume.

    Application



  • Page 39

    Adjusting Projected Images

    Mode
    Blackboard

    39

    Application
    Even if you are projecting onto a blackboard
    (greenboard), this setting gives your images a
    natural tint, just like when projecting onto a screen.

    Whiteboard

    Ideal for making presentations using a whiteboard.

    Customized

    Select Customized if you want to adjust the R, G,
    B, C, M, and Y settings in the Color Adjustment
    submenu of the Configuration menu.

    Setting Auto Iris
    By automatically setting the luminance according to the brightness of the
    displayed image, it lets you enjoy deep and rich images.

    a

    Press the [Menu] button.
    s "Using the Configuration Menu" p.67
    Using the remote control

    Using the control panel

    *1 This selection is only available when the input signal is RGB or when the
    source is USB Display, USB, or LAN. (Depending on the model used, some
    sources are not supported.)
    *2 This selection is only available when the input signal is component video, or
    when the source is Video.

    Each time you press the [Color Mode] button, the Color Mode name is
    displayed on the screen and the Color Mode changes.
    Remote control

    a

    b

    Select Auto Iris from Image.

    c

    Select On.

    You can set Color Mode from the Configuration menu.
    s Image - Color Mode p.70

    d

    The setting is stored for each Color Mode.
    Press the [Menu] button to finish making settings.



  • Page 40

    Adjusting Projected Images

    a

    Auto Iris can be set only when the Color Mode is Dynamic,
    Theatre, or Customized.

    Changing the Aspect Ratio

    40

    Changing the aspect ratio for video equipment images
    For EB-1775W/EB-1770W/EB-1760W

    Each time the button is pressed, the aspect ratio changes in the order of
    Normal or Auto, 16:9, Full, Zoom, and Native.

    Change the aspect ratiog when video equipment is connected so that
    images that have been recorded in digital video or onto DVDs can be
    viewed in 16:9 wide-screen format. Change the aspect ratio when projecting
    computer images at full size.
    Available Aspect Modes vary depending on the image signal currently being
    projected.
    The changing methods and the types of Aspect Modes are as follows.

    Changing methods
    Each time you press the [Aspect] button, the Aspect Mode name is
    displayed on the screen and the aspect ratio changes.
    Remote control

    A
    B
    C
    D
    E

    Normal or Auto
    16:9
    Full
    Zoom
    Native

    For EB-1750

    a

    You can set the aspect ratio from the Configuration menu.
    s Signal - Aspect p.71

    Each time the button is pressed, the aspect ratio changes in the order of
    Normal, 4:3, and 16:9.



  • Page 41

    Adjusting Projected Images

    A Normal
    B 4:3
    C 16:9
    * When a 720p/1080i signal is input, the display is in a zoomed 4:3 format (the
    image is cut off on the right and left sides).

    41



  • Page 42

    Adjusting Projected Images

    42

    Changing the aspect ratio for computer images
    For EB-1775W/EB-1770W/EB-1760W
    Each time the button is pressed, the aspect ratio changes in the order of Normal or Auto, 16:9, Full, Zoom, and Native.
    Computer Input
    Resolution

    Aspect Ratio

    XGA (1024x768)

    4:3

    WXGA (1280x800)

    16:10

    Projector Aspect Setting
    Normal/Auto *

    16:9

    Full

    Zoom

    Native

    * Only available when the source is HDMI.

    For EB-1750
    Each time the button is pressed, the aspect ratio changes in the order Normal, 4:3, and 16:9.
    Computer Input
    Resolution
    XGA (1024x768)

    Aspect Ratio
    4:3

    Projector Aspect Setting
    Normal

    4:3

    16:9



  • Page 43

    Adjusting Projected Images

    43

    Computer Input
    Resolution
    WXGA (1280x800)

    a

    Aspect Ratio

    Projector Aspect Setting
    Normal

    4:3

    16:9

    16:10

    If parts of the image are missing, set the Resolution setting to Wide or Normal from the Configuration menu, according to the size of the computer panel.
    s Signal - Resolution p.71



  • Page 44

    Useful Functions
    This chapter explains useful tips for giving presentations, and the Security functions.



  • Page 45

    Projection Functions

    45

    Projecting Without a Computer (Slideshow)
    By connecting a USB storage device such as a USB memory or a USB hard
    disk to the projector, you can project the files stored on the device without
    using a computer. This function is called Slideshow.
    You can make presentations with just a USB storage device and the
    projector by converting PowerPoint files to scenarios using the supplied
    EasyMP Slide Converter, and then saving them to the USB storage device.

    a

    • You may not be able to use USB storage devices that incorporate
    security functions.
    • You cannot correct keystone distortion while projecting a Slideshow,
    even if you press the [

    ], [

    ], [

    ], and [

    ] buttons on the

    control panel.

    Type

    Scenario
    file

    a

    File Type (Ex‐
    tension)

    Notes

    .png

    Cannot project images with a resolution greater
    than 1280x800.

    .fse

    PowerPoint files are converted to this format in
    EasyMP Slide Converter.

    .sit

    PowerPoint files are converted to this format using
    simplified conversion in EasyMP Slide Converter.
    None of the PowerPoint animation effects are
    converted.

    • When connecting and using a USB-compatible hard disk, make sure
    you connect the AC adaptor supplied with the hard disk.
    • The projector does not support some file systems, so use media that
    has been formatted in Windows.
    • Format the media in FAT16/32.

    Specifications for files that can be projected using Slideshow
    Type

    File Type (Ex‐
    tension)

    Notes

    Image

    .jpg

    The following cannot be projected.
    - CMYK color mode formats
    - Progressive formats
    - Images with a resolution greater than 8192x8192
    Due to the characteristics of JPEG files, images may
    not be projected clearly if the compression ratio is
    too high.

    .bmp

    Cannot project images with a resolution greater
    than 1280x800.

    .gif

    • Cannot project images with a resolution greater
    than 1280x800.
    • Cannot project animated GIFs.

    Slideshow examples
    Projecting images stored on USB storage

    jpg
    bmp
    gif
    png
    s "Projecting the selected image" p.48
    s "Projecting image files in a folder in sequence (Slideshow)" p.49



  • Page 46

    Projection Functions

    46

    • JPEG files are displayed as thumbnails (file contents are displayed
    as small images).

    Projecting PowerPoint files converted in EasyMP Slide Converter
    PPT

    fse
    sit

    • Scenarios (FSE files and SIT files) are displayed as thumbnails as
    the first image in the slide.
    • Other files or folders are displayed as icons as shown in the
    following table.

    USB

    Icon

    File
    FSE

    See the following manual for more information on converting PowerPoint
    files to scenarios using EasyMP Slide Converter.

    Icon
    files*

    File
    BMP files

    SIT files*

    GIF files

    JPEG files*

    PNG files

    s EasyMP Slide Converter Operation Guide

    Slideshow operating methods
    Although the following steps are explained based on the remote control,
    you can perform the same operations from the control panel.
    Starting Slideshow

    a

    Change the projected image to USB.

    b

    Connect the USB storage device or digital camera to the projector.

    s "Switching to the Target Image by Remote Control" p.28

    s "Connecting USB Devices" p.23

    Slideshow starts and the file list screen is displayed.

    *

    When it cannot be displayed as a thumbnail, it is displayed as an icon.



  • Page 47

    Projection Functions

    a

    47

    • When AutoRun is set for a scenario, it is automatically played back
    with the highest priority over other input sources. If you want to
    stop it from playing back, press the [Esc] button on the remote
    control.
    • You can also insert a memory card into a USB card reader and then
    connect the reader to the projector. However, some commercially
    available USB card readers may not be compatible with the
    projector.
    • If the following screen (Select Drive screen) is displayed, press the
    [

    ], [

    ], [

    ], and [

    ] buttons to select the drive

    you want to use, and then press the [Enter] button.

    a

    If not all of the files and folders are displayed on the current
    screen, press the [Down] button on the remote control, or
    position the cursor on Next Page at the bottom of the screen
    and press the [Enter] button.
    To return to the previous screen, press the [Up] button on the
    remote control, or position the cursor on Previous Page at the
    top of the screen and press the [Enter] button.

    b
    • To display the Select Drive screen, position the cursor on Select
    Drive at the top of the file list screen, and then press the [Enter]
    button.

    Use the [

    The selected image is displayed.
    When a folder is selected, the files in the selected folder are
    displayed. To return to the previous screen, position the cursor on
    Back to Top and press the [Enter] button.

    Rotating images

    Projecting images

    a

    Press the [Enter] button.

    ], [

    ], [

    ], and [

    file or folder you want to project.

    ] buttons to select the

    You can rotate the played images in 90˚ increments. The rotating function
    is also available during Slideshow.

    a

    Play images, or run Slideshow.



  • Page 48

    Projection Functions

    b

    While projecting, press the [

    48

    ] or [

    ] button.

    Stopping Slideshow

    b

    Press the [

    c

    Press the [Enter] button.

    ], [

    ], [

    ], and [

    ] buttons to select the

    image file you want to project.

    The image is displayed.

    To close Slideshow, disconnect the USB device from the USB port on the
    projector. For digital cameras, hard disks, and so on, turn off the power to
    the device and then remove.

    Projecting the selected image

    a

    Attention
    Do not disconnect the USB storage device while it is being accessed. An error
    may occur in Slideshow.

    a

    Start Slideshow.
    The file list screen is displayed.
    s "Starting Slideshow" p.46

    d

    Press the [

    ][

    ] buttons to move to the next or previous

    image file.

    Press the [Esc] button to return to the file list screen.



  • Page 49

    Projection Functions

    49

    Projecting image files in a folder in sequence (Slideshow)
    You can project the image files in a folder in sequence, one at a time. This
    function is called Slideshow. Use the following procedure to run
    Slideshow.

    a
    a

    To change files automatically when you run Slideshow, set Screen
    Switching Time from Option in Slideshow to anything other than No.
    The default setting is 3 seconds.

    a

    [

    ] button, the [Enter] button, or the [Down] button on the remote

    control to continue to the next file.

    Playing a scenario

    a

    Start Slideshow.

    If Screen Switching Time on the Option screen is set to No, files do
    not change automatically when you select Play Slideshow. Press the

    The file list screen is displayed.

    Start Slideshow.
    The file list screen is displayed.
    s "Starting Slideshow" p.46

    s "Starting Slideshow" p.46

    b
    c

    Use the [

    ][

    ][

    ][

    ] buttons to position the cursor

    over the folder for the Slideshow that you want to run and press
    the [Enter] button.
    Select Slideshow at the bottom right of the file list screen, and
    then press the [Enter] button.
    Slideshow starts, and the image files in the folder are automatically
    projected in sequence, one at a time.
    When the last file is projected, the file list is displayed again
    automatically. If you set Continuous Play to On in the Option
    window, projection starts again from the beginning again when it
    reaches the end.
    s "Image file display settings and Slideshow operation settings"

    p.50
    You can proceed to the next screen, return to the previous screen, or
    stop playback while projecting a Slideshow.

    b

    Press the [

    c

    Press the [Enter] button.

    ], [

    ], [

    ], and [

    ] buttons to select the

    scenario you want to playback.

    Playback starts.

    Operating procedures during scenario playback
    Screen switching
    For FSE files



  • Page 50

    Projection Functions

    50

    A
    B
    C
    D

    Next Slide
    Previous Slide
    Next Slide or Animation
    Previous Slide or Animation

    The following functions can be used when projecting a scenario or image
    file with Slideshow.
    • Freeze
    s "Freezing the Image (Freeze)" p.52
    • A/V Mute
    s "Hiding the Image and Sound Temporarily (A/V Mute)" p.51
    • E-Zoom
    s "Enlarging Part of the Image (E-Zoom)" p.53

    Image file display settings and Slideshow operation settings
    For SIT files

    A Next Slide
    B Previous Slide

    You can set the file display order and Slideshow operations on the Option
    screen.

    a
    b

    Press the [

    ][

    ][

    ][

    ] buttons to position the cursor

    over the folder where you want to set display conditions and press
    the [Esc] button. Select Option from the submenu displayed, then
    press the [Enter] button.
    When the following Option screen is displayed, set each of the
    items.
    Enable settings by positioning the cursor on the target item and
    pressing the [Enter] button.
    The following table shows the details for each item.

    Stopping playback
    The message "Do you want to quit playing the
    scenario?" is displayed when you press the [Esc]
    button. Close by selecting Exit and pressing
    the [Enter] button.
    Continue playback by selecting Return and
    pressing the [Enter] button.



  • Page 51

    Projection Functions

    51

    Hiding the Image and Sound Temporarily (A/V
    Mute)
    You can use this when you want to focus the audience's attention on what
    you are saying, or if you do not want to show details such as when you are
    changing between files during presentations from a computer.

    c

    Display Order

    You can select to display the files in Name Order or Date
    Order.

    Sort Order

    You can select to sort the files In Ascending or In
    Descending order.

    Continuous
    Play

    You can set whether to repeat the Slideshow.

    Screen Switch‐
    ing Time

    You can set the time for a single file to be displayed in Play
    Slideshow. You can set a time between No (0) to 60
    Seconds. When you set No, auto play is disabled.

    Effect

    You can set the screen effects when changing slides.

    When you have finished making settings, use the [
    [

    ], [

    ], and [

    Each time you press the [A/V Mute] button, or open/close the lens cover
    A/V Mute turns on or off.
    Remote control

    ],

    ] buttons to position the cursor over OK

    and press [Enter].
    The settings are applied.
    If you do not want to apply the settings, position the cursor on
    Cancel and press the [Enter] button.

    Projector



  • Page 52

    Projection Functions

    a

    • If you use this function when projecting moving images, the images
    and sound continue to be played back by the source, and you cannot
    return to the point where A/V Mute was activated.

    52

    a

    • You can select the screen displayed when the [A/V Mute] button is
    pressed from the Configuration menu.
    s Extended - Display - A/V Mute p.74
    • When the A/V mute slide is closed for approximately 30 minutes,
    Lens Cover Timer activates and the power is automatically turned
    off. If you do not want Lens Cover Timer to activate, set Lens Cover
    Timer to Off.
    s Extended - Operation - Lens Cover Timer p.74
    • The lamp is still lit during A/V Mute, so the lamp hours continue to
    accumulate.

    • Audio does not stop.
    • For moving images, the images continue to play back while the
    screen is frozen, so it is not possible to resume projection from the
    point where the screen was frozen.
    • If the [Freeze] button is pressed while the Configuration menu or
    the Help screen is displayed, the menu or the Help screen that is
    displayed is closed.
    • Freeze still works while E-Zoom is being used.

    Pointer Function (Pointer)
    This allows you to move a Pointer icon on the projected image, and helps
    you draw attention to the area you are talking about.

    Freezing the Image (Freeze)
    When Freeze is activated on moving images, the frozen image continues to
    project on the screen, so you can project a moving image one frame at a
    time like a still photo. Also, you can perform operations such as changing
    between files during presentations from a computer without projecting any
    images if the Freeze function is activated beforehand.
    Each time you press the [Freeze] button, Freeze turns on or off.
    Remote control

    a

    Display the Pointer.
    Each time you press the [Pointer] button, the pointer appears or
    disappears.
    Remote control



  • Page 53

    Projection Functions

    b

    Move the Pointer icon (

    53

    ).

    Enlarging Part of the Image (E-Zoom)

    Remote control

    When pressed in conjunction with the adjacent [
    [

    ], and [

    a

    This is useful when you want to expand images to see them in greater
    detail, such as graphs and tables.

    ], [

    ],

    ] buttons, the pointer can be moved diagonally.

    You can use Pointer Shape to set the shape of the pointer
    icon.
    s Settings - Pointer Shape p.73

    a

    Start E-Zoom.
    Press the [z] button to display the Cross (
    Remote control

    ).



  • Page 54

    Projection Functions

    b

    Move the Cross (

    54

    ) to the area of the image that you want to

    enlarge.
    Remote control

    a

    • The enlargement ratio appears on the screen. The selected
    area can be enlarged to between 1 to 4 times in 25
    incremental steps.
    • During enlarged projection, press the [
    [

    ], and [

    ], [

    ],

    ] buttons to scroll the image.

    • If E-Zoom is selected, Progressive and Noise Reduction are
    cancelled.

    When pressed in conjunction with the adjacent [
    [

    c

    ], and [

    ], [

    ],

    ] buttons, the pointer can be moved diagonally.

    Enlarge.
    Remote control
    [z] button: Expands the area each time
    it is pressed. You can expand quickly by
    holding the button down.
    [x] button: Reduces images that have
    been enlarged.
    [Esc] button: Cancels E-Zoom.

    Using the Remote Control to Operate the Mouse
    Pointer (Wireless Mouse)
    When the USB port of a computer and the USB (TypeB) port on the
    projector are connected with the supplied USB cable, you can use the
    remote control to control the computer's mouse pointer.
    This is only available when the source is Computer or HDMI (EB-1775W/
    EB-1770W/EB-1760W only).
    s "Connecting a Computer" p.21

    To activate the Wireless Mouse function, set USB Type B to Link 21L. By
    default, USB Type B is set to USB Display. Change the setting beforehand.
    s Extended - USB Type B p.74

    The following operating systems are compatible with Wireless Mouse.



  • Page 55

    Projection Functions

    55

    Windows

    OS

    *

    Windows
    Windows
    Windows
    Windows
    Windows
    Windows
    Windows

    Drag and drop

    Mac OS
    98
    98SE
    Me
    2000
    XP
    Vista
    7

    Mac
    Mac
    Mac
    Mac

    OS
    OS
    OS
    OS

    X
    X
    X
    X

    While holding down the [Enter] button,

    10.3.x
    10.4.x
    10.5.x
    10.6.x

    press the [
    [

    ], [

    ], [

    ], and

    ] buttons.

    Release the [Enter] button to drop at the
    desired location.

    It may not be possible to use the Wireless Mouse function under some
    versions of the operating systems.

    Once the connection has been made, the mouse pointer can be operated as
    follows.
    Moving the mouse pointer
    [

    ][

    ][

    ][

    ] buttons:

    Moves the mouse pointer.

    Mouse clicks
    [Enter] button: Left click. Press quickly twice
    to double-click.
    [Esc] button: Right click.

    Page Up/Down
    [Up] button: Moves to the previous page.
    [Down] button: Moves to the next page.



  • Page 56

    Projection Functions

    a

    56

    • When pressed in conjunction with the adjacent [
    [

    ], [

    ], and [

    ],

    ] buttons, the pointer can be moved

    diagonally.
    • If the mouse button settings are set to reverse on the computer, the
    operation of the remote control buttons will also be reversed.
    • The Wireless Mouse function cannot be used while the following
    functions are being used.
    - While the Configuration menu is being displayed
    - While a help menu is being displayed
    - While the E-Zoom function is being used
    - While a user's logo is being captured
    - While a pointer function is being used
    - While adjusting sound volume
    - While USB Display is being operated
    - While displaying a Test Pattern
    - While Color Mode is being set
    - While Color Mode name is being displayed
    - While the Source name is being displayed
    - While switching input source

    You can set an ID for the remote control within a range of "0" to "9". The
    default value is "0". The following table shows the possible combinations of
    Projector ID and remote control ID.
    Opera‐
    tion
    Possible

    Possible

    Projector ID: Off

    Remote control ID: 1

    Setting the ID and Using the Remote Control

    You can set an ID for the projector within a range of "1" to "9". The default
    value is Off.

    Projector ID: 1

    Remote control ID: 1

    Possible

    When an ID is set for the projector and the remote control, you can use
    the remote control to operate only the projector with a matching ID. This
    is useful when managing multiple projectors.

    Combinations

    Projector ID: 1

    Remote control ID: 0

    Not possi‐
    ble

    Projector ID: 1

    Remote control ID: 3

    Descriptions
    The projector ID and the
    remote control ID are
    identical, therefore you can
    operate the projector with the
    remote control.

    When the Projector ID is Off,
    you can operate with the
    remote control regardless of
    the remote control ID setting.

    When the remote control ID
    is "0", you can operate with
    the remote control regardless
    of the Projector ID setting.

    The Projector ID and the
    remote control ID do not
    match, therefore you cannot
    operate the projector with the
    remote control.



  • Page 57

    Projection Functions

    57

    Setting the Projector ID

    a

    Choose the ID you want to set and press the [Enter] button.

    d

    Press the [Menu] button to finish making settings.

    Press the [Menu] button while projecting.
    s "Using the Configuration Menu" p.67
    Using the remote control

    b

    c

    Select Projector ID from Extended.

    Using the control panel

    Setting the remote control ID
    Set the ID on the remote control each time you switch the projector power
    on. When the projector is powered on, the remote control ID is set to
    "0" (that is, you can operate the projector with the remote control regardless
    of the projector ID).



  • Page 58

    Projection Functions

    a

    Point the remote control at the remote receiver of the target
    projector and press the [ID] button on the remote control.
    When you press the [ID] button, the current Projector ID is
    displayed on the projection screen. It disappears in about three
    seconds.
    Remote control

    58

    Correcting Color when Projecting from Multiple
    Projectors
    When multiple projectors are lined up and projecting images, you can
    correct the brightness and color tone of each projector's image with multiscreen color adjustment so that the colors of images from each projector
    match closely.

    a

    In some cases the brightness and color tone may not match completely
    even after correction.

    Summary of correction procedure

    b

    While holding the [ID] button, press the number button that
    matches the ID of the projector you want to operate.

    When multiple projectors are set up and you need to make corrections, use
    the following procedure to correct one projector at a time.
    1. Set the projector ID and the remote control ID.
    Set a projector ID for the target projector, then set the same ID for the
    remote control, so that you can limit the operation to one target projector.
    s "Setting the ID and Using the Remote Control" p.56
    2. Correct the color difference.
    You can carry out color correction when projecting from multiple projectors.
    You can adjust from black to white in five stages called levels 1 to 5, and in
    each of these 5 levels you can adjust the following two points.

    • Correcting brightness
    You can correct the image brightness to make them all equal.
    Once this setting has been made, the projector that can be operated by the remote
    control is limited.

    a

    When you power off the projector, the remote control ID is reset to
    "0" (that is, you can operate the projector with the remote control
    regardless of the projector ID).

    • Correcting color
    You can correct the image color so that they match closely.

    Correcting
    After setting up the projectors, correct the brightness and tone for each
    projector to reduce the differences.



  • Page 59

    Projection Functions

    a

    Press the [Menu] button.

    b

    Select Multi-screen from Extended.

    59

    • When you select Level 5, all the images are adjusted to the
    darkest image from multiple projectors.
    • When you select Level 1, all the images are adjusted to the
    brightest image from multiple projectors.
    • When you select Level 2 to Level 4, all the images are adjusted to
    the mid-range brightness image from multiple projectors.
    • Because each time the [Enter] button is pressed the image
    displayed changes between the pattern display and the actual
    image, you can check the correction results and make corrections
    in the actual image.

    s "Using the Configuration Menu" p.67

    e
    f
    g
    c
    d

    Select the level to be corrected in Adjustment Level.
    • Each time a level is selected, the pattern of the level selected is
    displayed.
    • You can start correcting from any level, usually you can make it
    darker or lighter by correcting 1 to 5 or 5 to 1.
    Correct the brightness with Brightness Correct.

    Correct the Color Correct. (G/R) and Color Correct. (B/Y) settings.
    Repeat procedures 3 to 5 until corrections are finished.
    When all corrections are finished, press the [Menu] button to finish
    making settings.



  • Page 60

    Projection Functions

    60

    a

    Saving a User's Logo
    You can save the image that is currently being projected as a User's Logo.

    a
    a

    Once a User's Logo has been saved, the logo cannot be returned to the
    factory default.

    Project the image you want to save as the User's Logo, and then
    press the [Menu] button.
    s "Using the Configuration Menu" p.67
    Using the remote control

    Using the control panel

    • If User's Logo is selected when Keystone, E-Zoom, Aspect,
    Progressive, or Zoom are being performed, the function
    currently being performed is cancelled.

    c

    When the message "Choose this image as the User's Logo?" is
    displayed, select Yes.

    a
    d
    b

    Select User's Logo from Extended.

    • When User's Logo Protect from Password Protect is set to
    On, a message is displayed and the User's Logo cannot be
    changed. You can make changes after setting User's Logo
    Protect to Off.
    s "Managing Users (Password Protect)" p.62

    When you press the [Enter] button on the remote control or
    the control panel, the screen size may change depending on the
    signal to match the actual resolution of the image signal.

    Move the box to select the part of the image to use as the User's
    Logo.
    You can perform the same operations from the projector's control
    panel.



  • Page 61

    Projection Functions

    Remote control

    a
    e

    61

    f

    Select the zoom factor from the zoom setting screen.

    g

    When the message "Save this image as the User's Logo?" is
    displayed, select Yes.

    You can save at 400x300 dots in size.

    When you press the [Enter] button and the message "Select this
    image?" is displayed, select Yes.

    The image is saved. After the image has been saved, the message
    "Completed." is displayed.

    a

    • When a User's Logo is saved, the previous User's Logo is
    erased.
    • Saving the User's Logo may take approximately 15 seconds.
    Do not operate the projector or any connected equipment
    while it is saving, otherwise malfunctions may occur.



  • Page 62

    Security Functions
    The projector has the following enhanced security functions.
    • Password Protect
    You can limit who can use the projector.
    • Control Panel Lock
    You can prevent people changing the settings on the projector without
    permission.
    s "Restricting Operation (Control Panel Lock)" p.64
    • Anti-Theft Lock
    The projector is equipped with the following anti-theft security device.
    s "Anti-Theft Lock" p.65

    62

    • User's Logo Protect
    Even if someone tries to change the User's Logo set by the owner of the
    projector, it cannot be changed. When User's Logo Protect is set to On,
    the following setting changes for the User's Logo are prohibited.
    • Capturing a User's Logo
    • Setting Display Background, Startup Screen, or A/V Mute from
    Display
    s Extended - Display p.74
    • Network Protect (EB-1775W/EB-1770W/EB-1760W only)
    When Network Protect is set to On, changing the settings for Network is
    prohibited.
    s "Network Menu (EB-1775W/EB-1770W/EB-1760W Only)" p.76

    Managing Users (Password Protect)
    When Password Protect is activated, people who do not know the password
    cannot use the projector to project images even if the projector power is on.
    Furthermore, the user's logo that is displayed when you turn on the
    projector cannot be changed. This acts as an anti-theft device as the
    projector cannot be used even if it is stolen. At the time of purchase,
    Password Protect is not activated.

    Setting Password Protect
    Use the following procedure to set Password Protect.

    a

    During projection, hold down the [Freeze] button for about five
    seconds.
    The Password Protect setting menu is displayed.
    Remote control

    Kinds of Password Protect
    The following three kinds of Password Protect settings can be made
    according to how the projector is being used.
    • Power On Protect
    When Power On Protect is On, you need to enter a preset password after
    the projector is plugged in and turned on (this also applies to Direct
    Power On). If the correct password is not entered, projection does not
    start.



  • Page 63

    Security Functions

    a

    • If Password Protect is already activated, you must enter the
    password.
    If the password is entered correctly, the Password Protect
    setting menu is displayed.
    s "Entering the Password" p.63

    63

    (3)

    While holding down the [Num] button, enter a four digit number using
    the numeric buttons. The number entered is displayed as "* * * *". When
    you enter the fourth digit, the confirmation screen is displayed.
    Remote control

    • When the password is set, stick the supplied password protect
    sticker in a visible position on the projector as a further theft
    deterrent.

    b

    Select the type of Password Protect you want to set, and then
    press the [Enter] button.

    (4)

    Re-enter the password.
    The message "Password accepted." is displayed.
    If you enter the password incorrectly, a message is displayed prompting
    you to re-enter the password.

    Entering the Password
    When the password entry screen is displayed, enter the password using the
    numeric buttons on the remote control.
    While holding down the [Num] button, enter the password by pressing the
    numeric buttons.

    c
    d

    Select On, and then press the [Enter] button.
    Press the [Esc] button, the screen displayed in step 2 is displayed
    again.
    Set the password.
    (1)
    (2)

    Select Password, and then press the [Enter] button.
    When the message "Change the password?" is displayed, select Yes and
    then press the [Enter] button. The default password is set to "0000".
    Change this to your own desired password. If you select No, the screen
    displayed in step 2 is displayed again.



  • Page 64

    Security Functions

    When you enter the correct password, Password Protect is temporarily
    released.

    Attention
    • If an incorrect password is entered three times in succession, the message
    "The projector's operation will be locked." is displayed for approximately five
    minutes, and then the projector switches to standby mode. If this happens,
    disconnect the power plug from the electrical outlet and then reinsert it and
    turn the projector's power back on. The projector displays the password entry
    screen again so that you can enter the correct password.

    64

    This is useful at events or shows when you want to deactivate all buttons
    during projection or at schools when you want to limit button operation.
    The projector can still be operated using the remote control.

    a

    Press the [Menu] button while projecting.
    s "Using the Configuration Menu" p.67
    Using the remote control

    Using the control panel

    • If you have forgotten the password, make a note of the "Request Code:
    xxxxx" number that appears on the screen and contact the nearest address
    provided in the Epson Projector Contact List.
    s Epson Projector Contact List
    • If you continue to repeat the above operation and input the wrong password
    thirty times in succession, the following message is displayed and the
    projector does not accept any more password entries. "The projector's
    operation will be locked." "Contact Epson as described in your
    documentation."
    s Epson Projector Contact List

    b

    Select Control Panel Lock from Settings.

    c

    Select either Full Lock or Partial Lock according to your purpose.

    Restricting Operation (Control Panel Lock)
    Perform one of the following to lock the operation buttons on the control
    panel.
    • Full Lock
    All of the buttons on the control panel are locked. You cannot perform
    any operations from the control panel, including turning the power on or
    off.
    • Partial Lock
    All of the buttons on the control panel, except for the [t] button, are
    locked.



  • Page 65

    Security Functions

    65

    Anti-Theft Lock
    As an anti-theft measure, the projector is equipped with a security slot
    compatible with the Microsaver Security System manufactured by
    Kensington.
    See the following for more details on the Microsaver Security System.
    s http://www.kensington.com/

    d

    Select Yes when the confirmation message is displayed.
    The control panel buttons are locked according to the setting you
    chose.

    a

    You can release the control panel lock by one of the following
    two methods.
    • Select Off from Control Panel Lock.
    s Settings - Control Panel Lock p.73
    • Press and hold down the [Enter] button on the control panel
    for about seven seconds, a message is displayed and the lock
    is released.



  • Page 66

    Configuration Menu
    This chapter explains how to use the Configuration menu and its functions.



  • Page 67

    Using the Configuration Menu
    This section explains how to use the Configuration menu.
    Although steps are explained using the remote control as an example, you
    can perform the same operations from the control panel. Check the guide
    under the menu for the available buttons and their operations.

    a

    b

    67

    c

    Select a submenu item.

    d

    Change settings.

    e

    Press the [Menu] button to finish making settings.

    Display the Configuration menu screen.

    Select a top menu item.



  • Page 68

    List of Functions

    68

    Top Menu Name

    Configuration Menu Table

    Submenu Name
    Video Signal

    Auto, NTSC, NTSC4.43, PAL,
    M-PAL, N-PAL, PAL60, and
    SECAM

    Aspect

    Normal, 4:3, 16:9, Full, Zoom,
    and Native

    Overscan

    Auto, Off, 4%, and 8%

    Keystone

    H/V-Keystone and Quick Corner

    Control Panel Lock

    Full Lock, Partial Lock, and Off

    Settable items vary depending on the model being used and the image
    signal and source being projected.
    Top Menu Name
    Image menu
    s p.70

    Signal menu
    s p.71

    Submenu Name
    Color Mode

    Setting Values
    Dynamic, Presentation, Theatre,
    Photo, sRGB, Blackboard,
    Whiteboard, and Customized

    Settings menu
    s p.73

    Setting Values

    Brightness

    -24 to 24

    Contrast

    -24 to 24

    Pointer Shape

    Pointer 1, 2, and 3

    Color Saturation

    -32 to 32

    Power Consumption

    Normal and ECO

    Tint

    -32 to 32

    Volume

    0 to 20

    Sharpness

    -5 to 5

    Remote Receiver

    Front/Rear, Front, Rear and Off

    Abs. Color Temp.

    5000K to 10000K

    User Button

    Color Adjustment

    R: -16 to 16
    G: -16 to 16
    B: -16 to 16

    Power Consumption, Info,
    Progressive, Test Pattern, Multiscreen, and Resolution

    Test Pattern

    -

    Display

    Messages, Display Background,
    Startup Screen, and A/V Mute

    User's Logo

    -

    Projection

    Front, Front/Ceiling, Rear, and
    Rear/Ceiling

    Operation

    Direct Power On, Sleep Mode,
    Sleep Mode Timer, Lens Cover
    Timer, and High Altitude Mode

    Standby Mode

    Communication On and
    Communication Off

    Extended menu
    s p.74

    Auto Iris

    On and Off

    Auto Setup

    On and Off

    Resolution

    Auto, Wide, and Normal

    Tracking

    1216 to 1470

    Sync.

    0 to 31

    Position

    Up, Down, Left, and Right

    Progressive

    Off, Video, and Film/Auto

    Noise Reduction

    Off, NR1, and NR2

    HDMI Video Range

    Auto, Normal, and Expanded

    USB Type B

    USB Display and Link 21L

    Input Signal

    Auto, RGB, and Component

    Link 21L

    On and Off

    Projector ID

    Off and 1 to 9



  • Page 69

    List of Functions

    Top Menu Name

    69

    Submenu Name
    Multi-screen

    Info menu
    s p.84

    Reset menu
    s p.84

    Setting Values

    Top Menu Name

    Adjustment Level, Brightness
    Correct., Color Correct. (G/R),
    and Color Correct. (B/Y)

    Wireless LAN menu
    s p.79

    Channel

    1ch, 6ch, and 11ch

    Wireless LAN system

    802.11b/g and 802.11b/g/n

    SSID Auto Setting

    On and Off

    SSID

    -

    IP Settings

    DHCP, IP Address, Subnet Mask,
    and Gateway Address

    SSID Display

    On and Off

    IP Address Display

    On and Off

    Security

    None, WEP, WPA-PSK, and
    WPA2-PSK

    15 or 35 languages*1

    Lamp Hours

    -

    Source

    -

    Input Signal

    -

    Resolution

    -

    Video Signal

    -

    Refresh Rate

    -

    Sync Info

    -

    WEP Encryption

    128Bit and 64Bit

    Status

    -

    Format

    ASCII and HEX

    Serial Number

    -

    Key ID

    1, 2, 3, 4

    Event ID

    -

    Reset All

    -

    Reset Lamp Hours

    -

    Encryption Key 1, En‐ cryption Key 2, Encryp‐
    tion Key 3, and Encryp‐
    tion Key 4

    Security menu
    s p.80

    Network menu (EB-1775W/EB-1770W/EB-1760W only)

    Basic menu
    s p.78

    Setting Values

    Language

    *1 The number of supported languages differs depending on the region where the
    projector is purchased.

    Top Menu Name

    Submenu Name

    Submenu Name

    Mail menu
    s p.82

    Setting Values

    Projector Name

    -

    PJLink Password

    -

    Web Control Password

    -

    Projector Keyword

    On and Off

    Wireless LAN Power
    Connection Mode

    Authentication Type

    Open and Shared

    PSK

    -

    Mail Notification

    On and Off

    SMTP Server

    -

    Port Number

    -

    Address 1 Setting, Ad‐ dress 2 Setting, and Ad‐
    dress 3 Setting
    Others menu
    s p.82

    SNMP

    On and Off
    -

    On and Off

    Trap IP Address 1 and
    Trap IP Address 2

    Quick and Advanced

    AMX Device Discovery On and Off



  • Page 70

    List of Functions

    70

    Submenu

    Image Menu
    Settable items vary depending on the image signal and source currently
    being projected. Setting details are saved for each image signal.

    Sharpness

    You can adjust the image sharpness.

    Abs. Color Temp.

    (This item cannot be selected if Color Mode is set to sRGB g.)
    You can adjust the overall tint of the image. You can adjust tints
    in 10 stages from 5000 K to 10000 K. The image is tinted blue
    when a high value is selected and tinted red when a low value is
    selected.

    Color Adjust‐
    ment

    (This item cannot be selected if Color Mode is set to sRGB g.)
    • When Color Mode is set to anything other than Customized:
    You can adjust the color strength for Red, Green, and
    Blue individually.
    • When Color Mode is set to Customized:
    You can adjust the Hue, Saturation, and Brightness for R
    (red), G (green), B (blue), C (cyan), M (magenta), and Y
    (yellow) individually.

    Auto Iris

    (This item can be set only if Color Mode is set to Dynamic,
    Theatre, or Customized.)
    Set to On to adjust the iris to obtain the optimum light for images
    being projected.
    The setting is stored for each Color Mode.
    s "Setting Auto Iris" p.39

    Reset

    You can reset all adjustment values for the Image menu to their
    default settings. See the following to return all menu items to
    their default settings.
    s "Reset Menu" p.84

    s "Automatically Detect Input Signals and Change the Projected Image
    (Source Search)" p.27

    Submenu

    Function

    Color Mode

    You can select the quality of the image to suit your surroundings.
    s "Selecting the Projection Quality (Selecting Color Mode)"
    p.38

    Brightness

    You can adjust the image brightness.

    Contrast

    You can adjust the difference between light and dark in the
    images.

    Color Saturation

    You can adjust the color saturation for the images.

    Tint

    (Adjustment is only possible when NTSC signals are being input
    if you use composite video signals.)
    You can adjust the image tint.

    Function



  • Page 71

    List of Functions

    71

    Submenu

    Signal Menu

    Function

    Sync.

    Settable items vary depending on the image signal and source currently
    being projected. Setting details are saved for each image signal.

    You can adjust computer images when flickering, fuzziness, or
    interference appear in the images.

    Position

    You cannot make settings on the Signal menu when the source is USB
    Display, USB, or LAN.

    You can adjust the display position up, down, left, and right when
    a part of the image is missing so that the whole image is projected.

    Progressive

    (This setting can only be adjusted when a component video or
    RGB video with an interlaced signal (480i/576i/1080i) is input.
    This cannot be set when a digital RGB signal is input.)
    Interlaceg (i) signal is converted to Progressiveg (p). (IP
    conversion)
    Off: Ideal for images with a large amount of movement.
    Video: Ideal for general video images.
    Film/Auto: Ideal for movies, CG, and animation.

    Noise Reduction

    (This cannot be set when a digital RGB signal is input, or when an
    interlace signal is being displayed when Progressive is set to
    Off.)
    Smoothes out rough images. There are two modes. Select your
    favorite setting. It is recommended that this is set to Off when
    viewing image sources in which noise is very low, such as for
    DVDs.

    HDMI Video
    Range
    (EB-1775W/
    EB-1770W/
    EB-1760W only)

    When the projector's HDMI port is connected to a DVD player,
    the projector's video range is set according to the DVD player's
    video range setting.

    Input Signal

    You can select the input signal from the Computer port.
    If set to Auto, the input signal is set automatically according to
    the connected equipment.
    If colors do not appear correctly when set to Auto, select the
    appropriate signal according to the connected equipment.

    Video Signal

    You can select the input signal from the Video port. If this is set to
    Auto, video signals are recognized automatically. If interference
    appears in the image or a problem occurs such as no image is
    being projected when set to Auto, select the appropriate signal
    depending on the connected equipment.

    s "Automatically Detect Input Signals and Change the Projected Image
    (Source Search)" p.27

    Submenu

    Function

    Auto Setup

    Set to On to automatically adjust the image to the optimum state
    when the input signal changes.

    Resolution

    Set to Auto to automatically identify the resolution of the input
    signal. If images are not projected correctly when set to Auto, for
    example if some of the image is missing, adjust to Wide for wide
    screens, or set to Normal for 4:3 or 5:4 screens depending on the
    connected computer.

    Tracking

    You can adjust computer images when vertical stripes appear in
    the images.



  • Page 72

    List of Functions

    Submenu

    72

    Function

    Aspect

    You can set the aspect ratiog for projected images.
    s "Changing the Aspect Ratio" p.40

    Overscan

    (This cannot be set when a digital RGB signal is input.)
    Changes the output image ratio (the range of the projected
    image). You can set the cropping range to Off, 4%, or 8%. When
    the source is HDMI, Auto is available. When Auto is selected, it
    automatically changes to Off or 8% according to the input signal.
    However, this only occurs when the HDMI port of the connected
    device is connected to the projector's HDMI port.

    Reset

    You can reset all adjustment values on the Signal menu to their
    default settings, except for Input Signal.
    See the following to return all menu items to their default
    settings.
    s "Reset Menu" p.84



  • Page 73

    List of Functions

    73

    Submenu

    Settings Menu

    Pointer Shape

    Function
    You can select the shape of the pointer.
    Pointer 1:
    Pointer 2:
    Pointer 3:
    s "Using the Remote Control to Operate the Mouse Pointer
    (Wireless Mouse)" p.54

    Submenu
    Keystone

    Control Panel
    Lock

    Power Consump‐
    tion

    You can set the lamp brightness to one of two settings.
    Select ECO if the images being projected are too bright, such as
    when projecting images in a dark room or onto a small screen.
    When ECO is selected, the power consumption is changed as
    follows, and fan rotation noise during projection is reduced.
    Electrical consumption: about 27% decrease

    Volume

    You can adjust the volume. Setting values are saved for each
    source.

    Remote Receiver

    You can limit the reception of the operation signal from the
    remote control.
    When set to Off, you cannot perform any operations from the
    remote control. If you want to make operations from the remote
    control, hold down the [Menu] button on the remote control or
    the control panel for at least 15 seconds to reset the setting to its
    default value.

    User Button

    You can select and assign an item from the Configuration menu
    with the remote control's [User] button. Pressing the [User]
    button directly displays the assigned menu item selection/
    adjustment screen, allowing you to make one-touch changes to
    settings/adjustments. You can assign one of the following items
    to the [User] button.
    Power Consumption, Info, Progressive, Test Pattern, Multiscreen, and Resolution

    Function
    You can correct keystone distortion.
    • When H/V-Keystone is selected:
    • Correcting manually
    Adjust V-Keystone and H-Keystone to correct
    horizontal and vertical keystone distortion.
    • Correcting automatically
    Set Auto H/V-Keystone* to On.
    s "Correcting automatically - Auto H/V-Keystone (EB-1775W only)" p.33
    * When using EB-1770W/EB-1760W/EB-1750, set Auto
    V-Keystone to On.
    • When Quick Corner is selected:
    Select and correct the four corners of the projected image.
    s "Correcting manually - Quick Corner -" p.34
    You can use this to restrict operation of the projector's control
    panel.
    s "Restricting Operation (Control Panel Lock)" p.64



  • Page 74

    List of Functions

    Submenu

    74

    Function

    Test Pattern

    You can display a test pattern to adjust the projection without
    connecting other equipment when you set up the projector.
    While the test pattern is displayed, you can adjust keystone,
    zoom, and focus.
    To cancel the test pattern, press the [Esc] button on the remote
    control or the control panel.

    Reset

    You can reset all adjustment values on the Settings menu to their
    default settings, except for User Button.
    See the following to return all menu items to their default
    settings.
    s "Reset Menu" p.84

    Extended Menu

    Submenu

    Function

    Display

    You can make settings related to the projector's display.
    Messages: When set to Off, the following items will not be
    displayed.
    The name of the current selection when changing the
    source, color mode, or aspect ratio; a message when no
    image signal is input; warnings such as the High Temp
    Warning.
    Display Background*1: You can set the screen background
    to Black, Blue, or Logo when no image signal is available.
    Startup Screen*1: Set to On to display the User's Logo
    when projection starts.
    A/V Mute*1: You can set the screen displayed when the
    remote control's [A/V Mute] button is pressed to Black,
    Blue, or Logo.

    User's Logo*1

    You can change the user's logo that is displayed as a
    background during Display Background, A/V Mute, and so
    on.
    s "Saving a User's Logo" p.60

    Projection

    Select from one of the following projection methods
    depending on how the projector is installed.
    Front, Front/Ceiling, Rear, and Rear/Ceiling
    You can change the setting as follows by pressing down
    the [A/V Mute] button on the remote control for about five
    seconds.
    FrontWFront/Ceiling
    RearWRear/Ceiling
    s "Installation Methods" p.19



  • Page 75

    List of Functions

    Submenu
    Operation

    Standby Mode

    75

    Function
    Direct Power On: Set to On to turn on the projector
    simply by plugging it in.
    When the power cable is plugged in, note that the projector
    turns on automatically in cases such as a power outage
    being restored.
    Sleep Mode: When set to On, this automatically stops
    projection when no image signal is being input and no
    operations are carried out.
    Sleep Mode Timer: When Sleep Mode is set to On, you
    can set the time before the projector automatically turns off
    within a range of 1 to 30 minutes.
    Lens Cover Timer: When set to On, this turns off the
    power automatically 30 minutes after the A/V mute slide is
    closed.
    This is set to On by default.
    High Altitude Mode: Set to On when using the projector
    above an altitude of 1500 m.
    You can use network monitoring and control functions
    while the projector is in standby mode when this is set to
    Communication On. (EB-1775W/EB-1770W/EB-1760W
    only)
    You can monitor and control the status of the projector
    over the network by using SNMPg, or by using the
    EasyMP Monitor software.
    s "Useful Software" p.109

    USB Type B

    Set to USB Display when the projector and a computer are
    connected by a USB cable and computer images are
    projected.
    s "Projecting with USB Display" p.28
    Set to Link 21L to operate the mouse pointer by remote
    control.
    s "Using the Remote Control to Operate the Mouse
    Pointer (Wireless Mouse)" p.54

    Link 21L

    Set to On to use the Link 21L utility software.

    Submenu

    Function

    Projector ID

    Set the ID for the projector to a number between 1 and 9.
    Off indicates that no ID is set.
    s "Setting the Projector ID" p.57

    Multi-screen

    You can adjust the hue and brightness of each projected
    image when multiple projectors are lined up and projecting.
    Adjustment Level: You can adjust from black to white in
    five stages called Level 1 to 5, and in each of these 5 levels,
    you can adjust Brightness Correct. and Color Correct.
    Brightness Correct.: You can correct the difference in the
    brightness of each projector.
    Color Correct. (G/R) / Color Correct. (B/Y): You can
    correct the difference in the color of each projector.
    s "Correcting Color when Projecting from Multiple
    Projectors" p.58

    Language

    You can set the language for messages and menus.

    Reset

    You can reset the adjustment values for Display*1 and
    Operation*2 from the Extended menu to their default
    settings.
    See the following to return all menu items to their default
    settings.
    s "Reset Menu" p.84

    *1 When User's Logo Protect is set to On in Password Protect, settings related
    to user's logo cannot be changed. You can make changes after setting User's
    Logo Protect to Off.
    s "Managing Users (Password Protect)" p.62
    *2 Except for High Altitude Mode.



  • Page 76

    List of Functions

    76

    Network Menu (EB-1775W/EB-1770W/EB-1760W
    Only)
    When Network Protect is set to On in Password Protect, a message is
    displayed and the network settings cannot be changed. Set Network Protect
    to Off and then configure the network.
    s "Setting Password Protect" p.62

    Submenu

    Function

    Network Config‐
    uration

    The following menus are available for setting Network
    items.
    Basic, Wireless LAN, Security, Mail, Others, Reset, and
    Setup complete

    *

    Displays available region information for the Wireless LAN unit being used.
    For more details, contact your local dealer or the nearest address provided in
    the Epson Projector Contact List.

    s Epson Projector Contact List

    a

    By using the Web browser of a computer connected to the projector
    on a network, you can set functions and control the projector. This
    function is called Web Control. You can easily enter text using a
    keyboard to make settings for Web Control such as security settings.
    s "Changing Settings Using a Web Browser (Web Control)"
    p.111

    Notes on operating the Network menu
    Submenu

    Function

    Net. Info. - Wire‐
    less LAN

    Displays the following network setting status information.
    • Connection Mode
    • Antenna Level
    • Projector Name
    • SSID
    • DHCP
    • IP Address
    • Subnet Mask
    • Gateway Address
    • MAC Address
    • Region Code*

    Selecting from the top menu and sub menus, and changing selected items is
    the same as making operations from the Configuration menu.
    When done, make sure you go to the Setup complete menu, and select Yes,
    No, or Cancel. When you select Yes or No, you are returned to the
    Configuration menu.



  • Page 77

    List of Functions

    77

    Yes: Saves the settings and exits the Network menu.
    No: Does not save the settings and exits the Network menu.
    Cancel: Continues displaying the Network menu.

    Soft keyboard operations
    The Network menu contains items that require input of alphanumerics
    during setup. In this case, the following software keyboard is displayed. Use
    the [
    the [

    ], [
    ], [

    ], [
    ], [

    ], and [

    ], and [

    ] buttons on the remote control or

    ] buttons on the control panel to move the

    cursor to the desired key, and then press the [Enter] button to enter the
    alphanumeric character. Enter figures by holding down the [Num] button
    on the remote control, and pressing the numeric buttons. After inputting,
    press Finish on the keyboard to confirm your input. Press Cancel on the
    keyboard to cancel your input.

    • Each time the CAPS key is selected and the [Enter] button is pressed, it
    sets and changes between upper case and lower case letters.
    • Each time the SYM1/2 key is selected and the [Enter] button is pressed,
    it sets and changes the symbol keys for the section enclosed by the
    frame.



  • Page 78

    List of Functions

    78

    Basic menu

    Submenu
    Projector Key‐
    word

    Submenu

    Function

    Projector Name

    Displays the projector name used to identify the projector when
    connected to a network.
    When editing, you can enter up to 16 single-byte alphanumeric
    characters.

    PJLink Password

    Set a password to use when you access the projector using
    compatible PJLink software.
    You can enter up to 32 single-byte alphanumeric characters.

    Web Control
    Password

    Set a password to use when making settings and controlling the
    projector using Web Control. Enter no more than eight singlebyte alphanumeric characters. Web Control is a function that
    allows you to set up and control the projector by using the Web
    browser on a computer connected on a network.
    s "Changing Settings Using a Web Browser (Web Control)"
    p.111

    Function
    When set to On, you have to enter the keyword when you try to
    connect the projector to a computer via a network. As a result,
    you can prevent presentations from being interrupted by
    connections from other computers.
    Normally this should be set to On.
    s EasyMP Network Projection Operation Guide



  • Page 79

    List of Functions

    79

    Wireless LAN menu

    Submenu

    Submenu
    Wireless LAN
    Sys.

    Set the Wireless LAN system to either 802.11b/g or
    802.11b/g/n.
    This is set to 802.11b/g by default.

    SSID Auto Set‐
    ting

    Set to On to reduce the projector search time when connecting to
    a network using Quick from Connection Mode.
    Set to Off when connecting to multiple projectors at the same
    time.
    This is set to On by default.

    SSID

    Enter an SSIDg. When an SSID is provided for the wireless LAN
    system in which the projector participates, enter the SSID.
    You can enter up to 32 single-byte alphanumeric characters.

    IP Settings

    You can make network settings.
    DHCP: Set to On to make network settings using DHCPg. If this
    is set to On, you cannot set any more addresses.
    IP Address: You can input the IP addressg assigned to the
    projector. You can enter a number from 0 to 255 in each field of
    the address. However, the following IP addresses cannot be used.
    0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a
    number from 0 to 255)
    Subnet Mask: You can input the subnet maskg for the projector.
    You can enter a number from 0 to 255 in each field of the address.
    However, the following subnet masks cannot be used.
    0.0.0.0, 255.255.255.255
    Gateway Address: You can input the IP address for the gateway
    for the projector. You can enter a number from 0 to 255 in each
    field of the address. However, the following gateway addressesg
    cannot be used.
    0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a
    number from 0 to 255)

    SSID Display

    To prevent the SSIDg from being displayed on the LAN Standby
    screen, set this to Off.

    IP Address Dis‐
    play

    To prevent the IP addressg from being displayed on the LAN
    Standby screen, set this to Off.

    Function

    Wireless LAN
    Power

    Turn On when connecting the projector to the computer over
    wireless LAN.
    If you do not want to connect via wireless LAN, turn it Off to
    prevent unauthorized access by others.
    This is set to On by default.

    Connection
    Mode

    Set the connection mode when using EasyMP Network
    Projection to connect the projector and computer.
    This is set to Quick by default.
    See the following manual for details on connection mode.
    s EasyMP Network Projection Operation Guide

    Channel

    (This can only be set if Connection Mode is set to Quick.)
    Select the frequency band used by the wireless LAN from 1ch,
    6ch, or 11ch.
    This is set to 11ch by default.

    Function



  • Page 80

    List of Functions

    80

    Security menu
    Only available when the supplied or optional Wireless LAN unit is installed.

    Submenu
    Security

    WEP Encryption

    Submenu

    Function

    Encryption Key
    1/Encryption Key
    2/Encryption Key
    3/Encryption Key
    4

    You can enter the key used for WEP encryption. Enter the key in
    single-byte characters following instructions from the network
    administrator for the network in which the projector
    participates. The type and number of characters that can be
    entered differ depending on the WEP Encryption and Format
    settings.
    128Bit - ASCII: Single-byte alphanumeric, 13 characters.
    64Bit - ASCII: Single-byte alphanumeric, 5 characters.
    128Bit - HEX: 0 to 9 and A to F, 26 characters
    64Bit - HEX: 0 to 9 and A to F, 10 characters

    Authentication
    Type

    Set the WEP authentication type.
    Open: Uses open system authentication.
    Shared: Uses shared key authentication.

    PSK

    (This can only be set when WPA-PSK or WPA2-PSK are
    selected from Security.)
    You can enter a Pre-Shared Key (encrypted key) in single-byte
    alphanumeric characters. Enter at least 8 and up to 32 characters.

    Function
    Select the security type from the items that are displayed.
    When setting up Security, follow the instructions from the
    administrator of the network system you are about to access.
    You can set the encryption for WEP encryption.
    128Bit: Uses 128 (104) bit encoding.
    64Bit: Uses 64 (40) bit encoding.

    Format

    You can set the input method for the WEP encryption key.
    ASCII: Input text.
    HEX: Input in HEX (hexadecimal).

    Key ID

    Selects the WEP encryption ID key.

    Type of security
    When the supplied or optional wireless LAN unit is installed and being
    used in Advanced connection mode, it is strongly recommended that you
    set security. Select one of the following security methods.
    • WEP
    Data is encrypted with a code key (WEP key). This mechanism prevents
    communication unless the encrypted keys for the access point and the
    projector match.



  • Page 81

    List of Functions

    • WPA
    This is an encryption standard that improves security which is a weak
    point of WEP. Although there are multiple kinds of WPA encryption
    methods, this projector uses TKIP and AES.
    WPA also includes user authentication functions. WPA authentication
    provides two methods: using an authentication server, or authenticating
    between a computer and an access point without using a server. This
    projector supports the latter method, without a server.

    a

    For setting details, follow the directions from the network
    administrator of your network.

    81



  • Page 82

    List of Functions

    82

    Mail menu
    When this is set, you receive an email notification if a problem or warning
    occurs in the projector.
    s "Using the Mail Notification Function to Report Problems" p.113

    Submenu

    Function

    Address 1 Set‐
    ting, Address 2
    Setting, and Ad‐
    dress 3 Setting

    You can input the email address of the destination to send the
    notification email to. You can register up to three destinations.
    You can enter up to 32 single-byte alphanumeric characters for
    the email addresses.
    You can select the problems or warnings to be notified about by
    email. When the selected problem or warning occurs in the
    projector, an email is sent to the specified destination address
    notifying that a problem or warning has occurred. You can select
    multiple items from the displayed items.

    Others menu

    Submenu

    Function

    Mail Notification

    Set to On to send an email to the preset addresses when a problem
    or warning occurs with a projector.

    SMTP Server

    You can input the IP addressg for the SMTP server for the
    projector.
    You can enter a number from 0 to 255 in each field of the address.
    However, the following IP addresses cannot be used.
    127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from
    0 to 255)

    Port Number

    You can input the port number for the SMTP server. The default
    value is 25. You can input numbers between 1 to 65535.

    Submenu
    SNMP

    Function
    Set to On to monitor the projector using SNMP.
    To monitor the projector, you need to install the SNMP manager
    program on your computer. SNMP should be managed by a
    network administrator.
    The default value is Off.



  • Page 83

    List of Functions

    Submenu

    83

    Function

    Trap IP Address
    1/Trap IP Ad‐
    dress 2

    You can register up to two IP addresses for the SNMP trap
    notification destination. You can enter a number from 0 to 255 in
    each field of the address. However, the following IP addresses
    cannot be used. 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x
    is a number from 0 to 255)

    AMX Device Dis‐
    covery

    When the projector is connected to a network, set this to On
    when you want to allow the projector to be detected by AMX
    Device Discoveryg. Set this to Off if you are not connected to an
    environment controlled by a controller from AMX or AMX
    Device Discovery.

    Reset menu
    Resets all of the network settings.

    Submenu
    Reset network
    settings.

    Function
    To reset all of the Network settings, select Yes.



  • Page 84

    List of Functions

    84

    Submenu

    Info Menu (Display Only)

    Function

    Video Signal

    Lets you check the status of the image signals being projected and the status
    of the projector. Items that can be displayed vary depending on the source
    currently being projected. Depending on the model used, some input
    sources are not supported.

    You can display the settings for Video Signal in the Signal
    menu.

    Refresh Rate

    You can display the refresh rate

    Sync Info

    s "Automatically Detect Input Signals and Change the Projected Image
    (Source Search)" p.27

    You can display the image signal information.
    This information may be needed if service is required.

    Status

    This is information about errors that have occurred on the
    projector.
    This information may be needed if service is required.

    Serial Number

    Displays the projector's serial number.

    Event ID
    (EB-1775W/
    EB-1770W/
    EB-1760W only)

    Displays the application error log.
    s "About Event ID (EB-1775W/EB-1770W/EB-1760W
    Only)" p.116

    *

    The cumulative use time is displayed as "0H" for the first 10 hours. 10 hours
    and above is displayed as "10H", "11H", and so on.

    Reset Menu
    Submenu

    Function

    Lamp Hours

    You can display the cumulative lamp operating time*.
    When it reaches the lamp warning time, the characters are
    displayed in yellow.

    Source

    You can display the source name for the connected
    equipment currently being projected.

    Input Signal

    You can display the content of Input Signal set in the
    Signal menu according to the source.

    Resolution

    You can display the resolution.

    g.



  • Page 85

    List of Functions

    Submenu

    85

    Function

    Reset All

    You can reset all items in the Configuration menu to their
    default settings.
    The following items are not reset to their defaults: Input
    Signal, User's Logo, all items for Network menus*, Lamp
    Hours, Language, Password, User Button, and Multiscreen.

    Reset Lamp
    Hours

    Clears the cumulative lamp hours use time. Reset when you
    replace the lamp.

    * (EB-1775W/EB-1770W/EB-1760W only)



  • Page 86

    Troubleshooting
    This chapter explains how to identify problems and what to do if a problem is found.



  • Page 87

    Using the Help

    87

    If a problem occurs with the projector, the Help screen is displayed to assist
    you by pressing the Help button. You can solve problems by answering the
    questions.

    a

    c

    Confirm the selection.
    Using the remote control

    Using the control panel

    Press the [Help] button.
    The Help screen is displayed.
    Using the remote control

    Using the control panel

    Questions and solutions are displayed as shown on the screen below.
    Press the [Help] button to exit the Help.

    b

    Select a menu item.

    a
    Using the remote control

    Using the control panel

    See the following if the Help function does not provide a
    solution to the problem.
    s "Problem Solving" p.88



  • Page 88

    Problem Solving

    88

    If you are having a problem with the projector, first check the projector's indicators and refer to "Reading the Indicators" below.
    See the following if the indicators do not show clearly what the problem might be.
    s "When the Indicators Provide No Help" p.91

    Reading the Indicators
    The projector is provided with the following three indicators that indicate the operating status of the projector.

    A Power indicator

    Indicates the operating status.
    Standby condition
    When the [t] button is pressed in this condition, projection starts.
    Preparing for network monitoring or cool down in progress
    All buttons are disabled while the indicator is flashing.
    Warming up
    Warm-up time is about 30 seconds. After warm-up is complete, the indicator stops flashing.
    The [t] button is disabled during warm-up.
    Projecting

    B Lamp indicator
    C Temp indicator

    Indicates the projection lamp status.
    Indicates the internal temperature status.



  • Page 89

    Problem Solving

    89

    Refer to the following table to see what the indicators mean and how to remedy problems that they indicate.
    If all indicators are off, check that the power cable is connected correctly and that the power is being supplied normally.
    Sometimes, when the power cable is unplugged, the t indicator remains lit for a short period, but this is not a fault.
    : Lit
    Status

    Cause

    : Flashing

    : Off

    : Varies according to the projector status

    Remedy or Status

    Internal Error

    Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the
    Epson Projector Contact List.
    s Epson Projector Contact List

    Fan Error
    Sensor Error

    Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the
    Epson Projector Contact List.
    s Epson Projector Contact List

    High Temp Error
    (overheating)

    The lamp turns off automatically and projection stops. Wait for about five minutes. After about five minutes the projector switches to standby
    mode, so check the following two points.
    • Check that the air filter and air exhaust vent are clear, and that the projector is not positioned against a wall.
    • If the air filter is clogged, clean or replace it.
    s "Cleaning the Air Filter" p.101, "Replacing the Air Filter" p.106
    If the error continues after checking the points above, stop using the projector, remove the power plug from the electrical outlet, and contact
    your local dealer or the nearest address provided in the Epson Projector Contact List.
    s Epson Projector Contact List
    When using at an altitude of 1500 m or more, set High Altitude Mode to On.
    s "Extended Menu" p.74

    Lamp Error
    Lamp Failure

    Check the following two points.
    • Take out the lamp and check if it is cracked.
    s "Replacing the Lamp" p.103
    • Clean the air filter.
    s "Cleaning the Air Filter" p.101



  • Page 90

    Problem Solving

    Status

    90

    Cause

    Remedy or Status
    If it is not cracked: Reinstall the lamp and turn on the power.
    If the error continues: Replace the lamp with a new one and then turn on the power.
    If the error continues: Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest
    address provided in the Epson Projector Contact List.
    s Epson Projector Contact List
    If it is cracked: Contact your local dealer or the nearest address provided in the Epson Projector Contact List. (Images cannot be projected until
    the lamp is replaced.)
    s Epson Projector Contact List
    When using at an altitude of 1500 m or more, set High Altitude Mode to On.
    s "Extended Menu" p.74

    Auto Iris Error
    Power Err. (Ballast)

    Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the
    Epson Projector Contact List.
    s Epson Projector Contact List

    High Temp Warning

    (This is not an abnormality. However, if the temperature rises too high again, projection stops automatically.)
    • Check that the air filter and air exhaust vent are clear, and that the projector is not positioned against a wall.
    • If the air filter is clogged, clean or replace it.
    s "Cleaning the Air Filter" p.101, "Replacing the Air Filter" p.106

    Replace Lamp

    a

    Replace it with a new lamp.
    s "Replacing the Lamp" p.103
    If you continue to use the lamp after the replacement period has passed, the possibility that the lamp may explode increases. Replace it with a
    new lamp as soon as possible.

    • See the following if the projector is not operating properly, even though the indicators are all showing normal.
    s "When the Indicators Provide No Help" p.91
    • If the indicators are in a state not shown in this table, stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or
    the nearest address provided in the Epson Projector Contact List.
    s Epson Projector Contact List



  • Page 91

    Problem Solving

    91

    When the Indicators Provide No Help
    If any of the following problems occur and the indicators do not offer a
    solution, refer to the pages given for each problem.
    Problems Relating to Images
    sp.92
    • No images appear
    Projection does not start, the projection area is completely black,
    or the projection area is completely blue.
    • Moving images are not displayed
    Moving images being projected from a computer appear black
    and nothing is projected.

    sp.93

    • Projection stops automatically

    sp.93

    • The message "Not supported" is displayed

    sp.93

    • The message "No Signal" is displayed

    sp.93

    • Interference or distortion appear in images

    sp.95

    • The image is truncated (large) or small, or the aspect ratio is not
    suitable
    Only part of the image is displayed, or the height and width
    ratios of the image are not correct.

    sp.95

    sp.96
    • Image colors are not right
    The whole image appears purplish or greenish, images are black
    & white, or colors appear dull.
    • Images appear dark

    sp.97

    Problems when projection starts
    • The projector does not turn on

    sp.97

    Other Problems
    • No sound can be heard or the sound is faint

    sp.98

    • The remote control does not work

    sp.98

    • I want to change the language for messages and menus

    sp.99

    • Email is not received even if a problem occurs in the projector
    (EB-1775W/EB-1770W/EB-1760W only)

    sp.99



  • Page 92

    Problem Solving

    92

    Problems Relating to Images
    No images appear
    Check

    Remedy

    Did you press the [t] button?

    Press the [t] button to turn the power on.

    Are the indicators switched off?

    The power cable is not connected correctly or power is not being supplied.
    Connect the projector's power cable correctly.
    s "From Installation to Projection" p.26
    Check that your electrical outlet or power source is functioning correctly.

    Is A/V Mute active?

    Press the [A/V Mute] button on the remote control to cancel A/V Mute.
    s "Hiding the Image and Sound Temporarily (A/V Mute)" p.51

    Is the A/V mute slide closed?

    Open the A/V mute slide.
    s "Front/Top" p.10

    Are the Configuration menu settings correct?

    Reset all of the settings.
    s Reset - Reset All p.84
    When using USB Display, set USB Type B to USB Display.
    s Extended - USB Type B p.74

    Is the image to be projected completely black?
    (Only when projecting computer images)

    Some input images, such as screen savers, may be completely black.

    Is the image signal format setting correct?
    (Only when projecting images from a video source)

    Change the setting according to the signal for the connected equipment.
    s Signal - Video Signal p.71

    Is the USB cable connected correctly?
    (Only when projecting using USB Display)

    Check that the USB cable is connected correctly. Reconnect it if it is not connected or not connected properly.

    When Windows Media Center is displayed at full screen, you cannot project using USB Display or network connection.
    Is Windows Media Center displayed in full screen?
    (Only when projecting using USB Display or network connection) Reduce the screen size.
    Is an application using the Windows DirectX function displayed? Applications using the Windows DirectX function may not display images correctly.
    (Only when projecting using USB Display or network connection)



  • Page 93

    Problem Solving

    93

    Moving images are not displayed (only the moving image portion turns black)
    Check
    Is the computer's image signal being output to the LCD and the
    monitor?
    (Only when projecting images from a laptop computer or a
    computer with a built-in LCD screen)

    Remedy
    Change the image signal from the computer to external output only. Check your computer's documentation, or contact
    the computer's manufacturer.

    Projection stops automatically
    Check
    Is Sleep Mode set to On?

    Remedy
    Press the [t] button to turn the power on. If you do not want to use Sleep Mode, change the setting to Off.
    s Extended - Operation - Sleep Mode p.74

    The message "Not supported" is displayed
    Check
    Is the image signal format setting correct?
    (Only when projecting images from a video source)

    Remedy
    Change the setting according to the signal for the connected equipment.
    s Signal - Video Signal p.71

    Do the image signal resolution and the refresh rate correspond to the Refer to the computer's documentation for how to change the image signal resolution and the refresh rate output from
    mode?
    the computer.
    (Only when projecting computer images)
    s "Supported Monitor Displays" p.121

    The message "No Signal" is displayed
    Check

    Remedy

    Are the cables connected correctly?

    Check that all the cables required for projection are securely connected.
    s "From Installation to Projection" p.26

    Is the correct port selected?

    Change the image by pressing the [Source Search] button on the remote control or the control panel.
    s "Automatically Detect Input Signals and Change the Projected Image (Source Search)" p.27

    Is the power for the computer or video source turned on?

    Turn the power on for the equipment.



  • Page 94

    Problem Solving

    94

    Check
    Are the image signals being output to the projector?
    (Only when projecting images from a laptop computer or a
    computer with a built-in LCD screen)

    Remedy
    If the image signals are only being output to the computer's LCD monitor or to the accessory monitor, you need to
    change the output to an external destination as well as the computer's own monitor. For some computer models, when
    the image signals are output externally, they no longer appear on the LCD monitor or accessory monitor.
    If the connection is made while the power of the projector or computer is already turned on, the Fn key (Function key)
    that changes the computer's image signal to external output may not work. Turn the power for the computer and the
    projector off and then back on again.
    s "From Installation to Projection" p.26
    s Computer's documentation

    Images are fuzzy, out of focus, or distorted
    Check

    Remedy

    Is the distance between the projector and the screen over 2.5 m? (For For the projected image to be automatically adjusted by Auto H/V-Keystone or Screen Fit, the projector cannot be more
    EB-1775W)
    than approximately 1.0 to 2.5 m away from the screen. If the projector must be placed further away than this, manually
    adjust the projected image.
    Is Auto H/V-Keystone set to Off? (EB-1775W only)

    Setting it to On enables Auto H/V-Keystone.
    s Settings - Keystone - Auto H/V-Keystone p.73
    If you are using the projector with this setting off, manually adjust the projected image.
    s "Correcting manually - manual H/V-Keystone -" p.34

    Is the focus adjusted correctly?

    Adjust the focus using the [Focus] buttons (EB-1775W only) or Focus ring (EB-1770W/EB-1760W/EB-1750 only).
    s "Correcting the Focus" p.37

    Is the projector at the correct distance?

    Is it projecting outside of the recommended projection distance range?
    Setup within the recommended range.
    s "Screen Size and Projection Distance" p.118

    Is the keystone adjustment value too large?

    Lower the projection angle to reduce the amount of keystone correction.
    s "Adjusting the Image Position" p.37

    Has condensation formed on the lens?

    If the projector is suddenly taken from a cold environment to a warm environment, or if sudden ambient temperature
    changes occur, condensation may form on the surface of the lens, and this may cause the images to appear fuzzy. Set the
    projector up in the room about one hour before it is used. If condensation forms on the lens, turn the projector off and
    wait for the condensation to disappear.



  • Page 95

    Problem Solving

    95

    Interference or distortion appear in images
    Check

    Remedy

    Is the image signal format setting correct?
    (Only when projecting images from a video source)

    Change the setting according to the signal for the connected equipment.
    s Signal - Video Signal p.71

    Are the cables connected correctly?

    Check that all the cables required for projection are securely connected.
    s "Connecting Equipment" p.21

    Is an extension cable being used?

    If an extension cable is used, electrical interference may affect the signals. Use the cables supplied with the projector to
    check if the cables you are using may be causing the problem.

    Is the correct resolution selected?
    (Only when projecting computer images)

    Set the computer so that the signals being output are compatible with the projector.
    s "Supported Monitor Displays" p.121
    s Computer's documentation

    Are the Sync.g and Trackingg settings adjusted correctly?
    (Only when projecting computer images)

    Press the [Auto] button on the remote control or the [Enter] button on the control panel to perform automatic
    adjustment. If the images are not adjusted correctly even after performing automatic adjustment, you can also make
    adjustments from the Configuration menu.
    s Signal - Tracking, Sync. p.71

    Is Transfer layered window selected?
    (Only when projecting using USB Display)

    Click All Programs - EPSON Projector - EPSON USB Display - EPSON USB Display Vx.xx Settings, and then clear
    the Transfer layered window checkbox.

    The image is truncated (large) or small, or the aspect is not suitable
    Check

    Remedy

    Is a wide panel computer image being projected?
    (Only when projecting computer images)

    Change the setting according to the signal for the connected equipment.
    s Signal - Resolution p.71

    Is the image still being enlarged by E-Zoom?

    Press the [Esc] button on the remote control to cancel E-Zoom.
    s "Enlarging Part of the Image (E-Zoom)" p.53

    Is the image position adjusted correctly?

    Press the [Auto] button on the remote control or the [Enter] button on the control panel to perform automatic
    adjustment of the computer image being projected. If the images are not adjusted correctly even after performing
    automatic adjustment, you can also make adjustments from the Configuration menu.
    Apart from computer image signals, you can adjust other signals while projecting from the Configuration menu.
    s Signal - Position p.71



  • Page 96

    Problem Solving

    96

    Check

    Remedy

    Is the computer set for dual display?
    (Only when projecting computer images)

    If dual display is activated in the Display Properties of the computer's Control Panel, only about half of the image on the
    computer screen is projected. To display the entire image on the computer screen, turn off the dual display setting.
    s Computer video driver documentation

    Is the correct resolution selected?
    (Only when projecting computer images)

    Set the computer so that the signals being output are compatible with the projector.
    s "Supported Monitor Displays" p.121
    s Computer's documentation

    Image colors are not right
    Check

    Remedy

    Do the input signal settings match the signals from the connected
    device?

    Change the following settings according to the signal for the connected equipment.
    • When image is from a device connected to the Computer port
    s Signal - Input Signal p.71
    • When image is from a device connected to the Video port
    s Signal - Video Signal p.71

    Is the image brightness adjusted correctly?

    Adjust the Brightness setting from the Configuration menu.
    s Image - Brightness p.70

    Are the cables connected correctly?

    Check that all the cables required for projection are securely connected.
    s "Connecting Equipment" p.21

    Is the contrastg adjusted correctly?

    Adjust the Contrast setting from the Configuration menu.
    s Image - Contrast p.70

    Is the color adjustment set correctly?

    Adjust the Color Adjustment setting from the Configuration menu.
    s Image - Color Adjustment p.70

    Are the color saturation and tint adjusted correctly?
    (Only when projecting images from a video source)

    Adjust the Color Saturation and Tint settings from the Configuration menu.
    s Image - Color Saturation, Tint p.70



  • Page 97

    Problem Solving

    97

    Images appear dark
    Check

    Remedy

    Is the image brightness set correctly?

    Adjust the Brightness and Power Consumption settings from the Configuration menu.
    s Image - Brightness p.70
    s Settings - Power Consumption p.73

    Is the contrastg adjusted correctly?

    Adjust the Contrast setting from the Configuration menu.
    s Image - Contrast p.70

    Is it time to replace the lamp?

    When the lamp is nearly ready for replacement, the images become darker and the color quality becomes poorer. When
    this happens, replace the lamp with a new lamp.
    s "Replacing the Lamp" p.103

    Problems when Projection Starts
    The projector does not turn on
    Check

    Remedy

    Did you press the [t] button?

    Press the [t] button to turn the power on.

    Are the indicators switched off?

    The power cable is not connected correctly or power is not being supplied.
    Disconnect and then reconnect the power cable.
    s "From Installation to Projection" p.26
    Check that your electrical outlet or power source is functioning correctly.

    Do the indicators turn on and off when the power cable is touched? There is probably a poor contact in the power cable, or the power cable may be defective. Reinsert the power cable. If this
    does not solve the problem, stop using the projector, disconnect the power cable from the electrical outlet, and contact
    your local dealer or the nearest address provided in the Epson Projector Contact List.
    s Epson Projector Contact List
    Is the Control Panel Lock set to Full Lock?

    Press the [t] button on the remote control. If you do not want to use Control Panel Lock, change the setting to Off.
    s Settings - Control Panel Lock p.73

    Is the correct setting for the remote receiver selected?

    Check the Remote Receiver from the Configuration menu.
    s Settings - Remote Receiver p.73



  • Page 98

    Problem Solving

    98

    Other Problems
    No sound can be heard or the sound is faint
    Check

    Remedy

    Check that the audio/video cable is securely attached to both the
    projector and audio source.

    Disconnect the cable from the Audio port, and then reconnect the cable.

    Is the volume adjusted to the minimum setting?

    Adjust the volume so that sound can be heard.
    s Settings - Volume p.73
    s "Adjusting the Volume" p.38

    Is A/V Mute active?

    Press the [A/V Mute] button on the remote control to cancel A/V Mute.
    s "Hiding the Image and Sound Temporarily (A/V Mute)" p.51

    Is the audio cable's specification "No resistance"?

    When using a commercially available audio cable, make sure it is labeled "No resistance".

    Is it connected with an HDMI cable?
    (EB-1775W/EB-1770W/EB-1760W only)

    If no audio is output when connecting via an HDMI cable, set the connected equipment to PCM output.

    Is Output audio from the projector selected?
    (Only when projecting using USB Display)

    Click All Programs - EPSON Projector - EPSON USB Display - EPSON USB Display Vx.xx Settings, and then select
    Output audio from the projector.

    The remote control does not work
    Check

    Remedy

    Is the remote control light-emitting area pointing towards the
    remote receiver on the projector during operation?

    Point the remote control towards the remote receiver.
    s "Remote control operating range" p.17

    Is the remote control too far from the projector?

    The operating range for the remote control is about 6 m.
    s "Remote control operating range" p.17

    Is direct sunlight or strong light from fluorescent lamps shining onto Set the projector up in a location where strong light does not shine onto the remote receiver. Or set the remote receiver to
    the remote receiver?
    Off from Remote Receiver in the Configuration menu.
    s Settings - Remote Receiver p.73
    Is the correct setting for the Remote Receiver selected?

    Check the Remote Receiver from the Configuration menu.
    s Settings - Remote Receiver p.73



  • Page 99

    Problem Solving

    99

    Check

    Remedy

    Are the batteries dead or have the batteries been inserted correctly? Make sure the batteries are inserted correctly or replace the batteries with new ones if necessary.
    s "Replacing the remote control batteries" p.17
    Are the remote control ID and the projector ID matched?

    Make sure the ID for the projector you want to operate and the ID for the remote control match. To operate all projectors
    by remote control regardless of the ID setting, set the remote control ID to "0".
    s "Setting the remote control ID" p.57

    I want to change the language for messages and menus
    Check
    Change the Language setting.

    Remedy
    Adjust the Language setting from the Configuration menu.
    s Extended - Language p.74

    Email is not received even if a problem occurs in the projector (EB-1775W/EB-1770W/EB-1760W only)
    Check

    Remedy

    Is Standby Mode set to Communication On?

    To use the Mail Notification function when the projector is in standby, set Communication On in Standby Mode from
    the Configuration menu.
    s Extended - Standby Mode p.74

    Did a fatal abnormality occur and the projector come to a sudden
    stop?

    When the projector comes to a sudden stop, email cannot be sent.
    If the abnormal state continues, contact your local dealer or the nearest address provided in the Epson Projector Contact
    List.
    s Epson Projector Contact List

    Is power being supplied to the projector?

    Check that your electrical outlet or power source is functioning correctly.

    Is Mail Notification function set correctly in the Configuration
    menu?

    An error notification email is sent according to the Mail settings in the Configuration menu. Check if it is set correctly.
    s"Mail menu" p.82



  • Page 100

    Maintenance
    This chapter provides information on maintenance procedures to ensure the best level of performance from the projector for a long time to come.



  • Page 101

    Cleaning
    You should clean the projector if it becomes dirty or if the quality of
    projected images starts to deteriorate.

    Attention

    101

    Attention
    Do not rub the lens with harsh materials or subject the lens to shocks, as it
    can easily become damaged.

    Turn off the projector's power before cleaning.

    Cleaning the Air Filter
    Cleaning the Projector's Surface
    Clean the projector's surface by wiping it gently with a soft cloth.
    If the projector is particularly dirty, moisten the cloth with water containing
    a small amount of neutral detergent, and then firmly wring the cloth dry
    before using it to wipe the projector's surface.

    Attention
    Do not use volatile substances such as wax, alcohol, or thinner to clean the
    projector's surface. The quality of the case may change or become discolored.

    Cleaning the Lens
    Use a commercially available cloth for cleaning glasses to gently wipe the
    lens.

    Warning
    Do not use sprays that contain flammable gas to remove dust and lint from the
    lens. The projector may catch fire due to the high internal temperature of the
    lamp.

    Clean the air filter and the air intake vent when the following message is
    displayed.
    "The projector is overheating. Make sure nothing is blocking the air vent,
    and clean or replace the air filter."

    Attention
    • If dust collects on the air filter it can cause the internal temperature of the
    projector to rise, and this can lead to problems with operation and shorten
    the optical engine's service life. Clean the air filter immediately when the
    message is displayed.
    • Do not rinse the air filter in water. Do not use detergents or solvents.



  • Page 102

    Cleaning

    a

    102

    • If a message is frequently displayed, even after cleaning, it is time to
    replace the air filter. Replace it with a new air filter.
    s "Replacing the Air Filter" p.106
    • It is recommended that you clean these parts at least once every
    three months. Clean them more often than this if using the projector
    in a particularly dusty environment.



  • Page 103

    Replacing Consumables
    This section explains how to replace the lamp and the air filter.

    103

    • The lamp indicator flashes orange.

    Replacing the Lamp
    Lamp replacement period
    It is time to replace the lamp when:
    • The message "Replace the lamp." is displayed at the lower left of the
    projection screen when you start projecting.

    • The projected image gets darker or starts to deteriorate.
    The message is displayed for 30 seconds.

    Attention
    • The lamp replacement message is set to appear after the following time
    periods in order to maintain the initial brightness and quality of the projected
    images.
    Lamp operating life: about 3900 hours
    • If you continue to use the lamp after the replacement period has passed, the
    possibility that the lamp may explode increases. When the lamp replacement
    message appears, replace the lamp with a new one as soon as possible, even if
    it is still working.
    • Do not repeatedly turn off the power and immediately back on. Turning the
    power on and off frequently may shorten the lamp's operating life.
    • Depending on the characteristics of the lamp and the way it has been used,
    the lamp may become darker or stop working before the lamp warning
    message appears. You should always have a spare lamp unit ready in case it is
    needed.



  • Page 104

    Replacing Consumables

    104

    How to replace the lamp
    The lamp can be replaced even when the projector is suspended from a
    ceiling.

    Warning
    • When replacing the lamp because it has stopped illuminating, there is a
    possibility that the lamp may be broken. If replacing the lamp of a projector
    which has been installed on the ceiling, you should always assume that the
    lamp is cracked, and you should stand to the side of the lamp cover, not
    underneath it. Remove the lamp cover gently.
    • Never disassemble or remodel the lamp. If a modified or disassembled lamp
    is installed in the projector and used, it could cause a fire, electric shock, or
    an accident.

    Then slide the lamp cover straight forward and lift it to remove.

    Caution
    Wait until the lamp has cooled down sufficiently before removing the lamp
    cover. If the lamp is still hot, burns or other injuries may result. It takes about
    one hour after the power has been turned off for the lamp to be cool enough.

    a

    After you turn off the projector's power and the confirmation
    buzzer beeps twice, disconnect the power cable.

    b

    Wait until the lamp has sufficiently cooled down, and then remove
    the lamp cover at the top of the projector.
    Loosen the lamp cover fixing screw with the screwdriver supplied
    with the new lamp unit or a + head screwdriver.

    c

    Raise the lamp fixing spring.



  • Page 105

    Replacing Consumables

    d

    105

    e

    Install the new lamp.

    f

    Lower the lamp fixing spring, and press down on the left and right
    until it clicks into place.

    Insert the new lamp along the guide rails in the correct direction so
    that it fits, and push it firmly into place. Press down on the part
    marked PUSH to fix the lamp in place.

    Raise the handle and take out the old lamp.
    If the lamp is cracked, contact your local dealer or the nearest
    address provided in the Epson Projector Contact List.
    s Epson Projector Contact List



  • Page 106

    Replacing Consumables

    g

    Replace the lamp cover.
    Insert the hook as shown in the illustration below, and attach the
    cover. Tighten the lamp cover fixing screw.

    106

    Replacing the Air Filter
    Air filter replacement period
    It is time to replace the air filter when:
    • There is a tear in the air filter.
    • The message is displayed even though the air filter has been cleaned.

    How to replace the air filter
    The air filter can be replaced even when the projector is suspended from a
    ceiling.

    Attention
    • Make sure you install the lamp securely. If the lamp cover is removed, the
    power turns off automatically as a safety precaution. If the lamp or the lamp
    cover is not installed correctly, the power does not turn on.
    • This product includes a lamp component that contains mercury (Hg). Please
    consult your local regulations regarding disposal or recycling. Do not dispose
    of it with normal waste.

    Resetting the lamp hours
    The projector records how long the lamp is turned on and a message and
    indicator notify you when it is time to replace the lamp. After replacing the
    lamp, make sure you reset the Lamp Hours from the Configuration menu.
    s "Reset Menu" p.84

    a

    Only reset the Lamp Hours after the lamp has been replaced.
    Otherwise the lamp replacement period is not indicated correctly.

    a

    After you turn off the projector's power and the confirmation
    buzzer beeps twice, disconnect the power cable.

    b

    Remove the air filter.
    Grip the tab in the center of the air filter, and pull it straight out.



  • Page 107

    Replacing Consumables

    c

    Install the new air filter.
    Push in the air filter until it clicks into place.

    a

    Dispose of used air filters properly in accordance with your local
    regulations.
    Material of the frame part: Polyphenylene ether and polystyrene resin
    Material of the filter part: Polyurethane foam

    107



  • Page 108

    Appendix



  • Page 109

    Useful Software

    109

    EasyMP Network Projection
    (EB-1775W/EB-1770W/EB-1760W only)
    By using the supplied EasyMP Network Projection, you can project your
    computer screen from the projector via a network. Sharing the projector
    over the network allows you to project data from different computers
    without changing the signal cable. Even if the projector is away from the
    computer, you can still project data via a network. You can also output the
    computer's audio from the projector.
    This projector only supports network projection using a wireless LAN
    connection.

    See the following for more details.
    s EasyMP Slide Converter Operation Guide
    s "Slideshow operating methods" p.46

    EasyMP Monitor
    (EB-1775W/EB-1770W/EB-1760W only)
    By using EasyMP Monitor, you can check the status of multiple Epson
    projectors on the network, and you can control them from your computer.
    You can download EasyMP Monitor from the following Web site.
    http://www.epson.com
    See the following for more details.
    s EasyMP Network Projection Operation Guide

    EasyMP Slide Converter
    By using the supplied EasyMP Slide Converter, you can convert PowerPoint
    files to scenarios that can be played directly from the projector.
    Save the converted scenario to a USB storage device. When the USB storage
    device is connected to the projector, Slideshow starts.



  • Page 110

    Optional Accessories and Consumables
    The following optional accessories and consumables are available. Please
    purchase these products as and when needed. The following list of optional
    accessories and consumables is current as of: August 2010. Details of
    accessories are subject to change without notice and availability may vary
    depending on the country of purchase.

    Optional Accessories
    50" portable screen

    ELPSC06

    110

    Wireless LAN unit ELPAP07 (EB-1770W/EB-1760W only)
    Use when connecting the projector to a computer wirelessly and projecting.

    Quick Wireless Connection USB Key ELPAP08 (EB-1775W/
    EB-1770W/EB-1760W only)
    Use when you want to quickly establish one-to-one connection between the
    projector and a computer with Windows installed.

    Ceiling pipe (450 mm) * ELPFP13
    Ceiling pipe (700 mm) * ELPFP14
    Use when installing the projector on a high ceiling.

    A compact screen that can be carried easily. (aspect ratiog 4:3)

    Ceiling mount* ELPMB23

    60" portable screen ELPSC27
    80" portable screen ELPSC28
    100" screen ELPSC29

    Use when installing the projector on a ceiling.

    Portable roll-type screens. (aspect ratio 4:3)

    53" portable screen
    64" portable screen

    ELPSC30
    ELPSC31

    Portable magnetic screens. (aspect ratio 4:3)

    Computer cable ELPKC02
    (1.8 m - for mini D-Sub15-pin/mini D-Sub 15pin)
    This is the same as the computer cable supplied with the projector.

    Computer cable ELPKC09
    (3 m - for mini D-Sub15-pin/mini D-Sub 15pin)
    Computer cable ELPKC10
    (20 m - for mini D-Sub15-pin/mini D-Sub 15pin)
    Use one of these longer cables if the computer cable supplied with the projector
    is too short.

    Component video cable ELPKC19
    (3 m - for mini D-Sub 15-pin/RCA male^3)
    Use to connect a component videog source.

    Document camera ELPDC06
    Use when projecting images such as books, OHP documents, or slides.

    Attachment plate* ELPPT01
    Use when attaching the ceiling mount to the projector.
    Special expertise is required to suspend the projector from a ceiling. Contact
    your local dealer or the nearest address provided in the Epson Projector
    Contact List.
    s Epson Projector Contact List
    *

    Consumables
    Lamp unit ELPLP65
    Use as a replacement for used lamps.

    Air filter ELPAF31
    Use as a replacement for used air filters.



  • Page 111

    Monitoring and Controlling (EB-1775W/EB-1770W/EB-1760W Only)
    Changing Settings Using a Web Browser (Web
    Control)
    By using the Web browser of a computer connected to the projector on a
    network, you can make settings and control the projector. This function
    allows you to perform setup and control operations remotely. In addition,
    since you can use the computer's keyboard, entering characters required for
    the setup is easier.
    Use Microsoft Internet Explorer 6.0 or later as the Web browser. You can
    also use Safari if you are using Mac OS.

    a

    If you set Standby Mode to Communication On, you can use the
    Web browser to make settings and perform control even if the
    projector is in standby mode (when the power is off).
    s Extended - Standby Mode p.74

    Projector setup
    In the Web browser, you can set items that are usually set in the projector's
    Configuration menu. The settings are reflected in the Configuration menu.
    There are also items that can only be set in the Web browser.

    111

    The settings for items on each menu are the same as the projector's
    Configuration menu.
    s "Configuration Menu" p.66
    Items that can only be set with a Web browser

    • SNMP Community Name
    • Monitor Password

    Displaying the Web Control screen
    Use the following procedure to display the Web Control screen.

    a
    a
    b

    If your Web browser is set up to connect via a proxy server, the Web
    Control screen cannot be displayed. To display Web Control, you need
    to make settings so that a proxy server is not used for a connection.

    Start the Web browser on the computer.
    Enter the IP address of the projector in the address input box of
    the Web browser, and press the Enter key on the computer's
    keyboard.
    The Web Control screen is displayed.

    Items in the Configuration menu that cannot be set by the Web browser










    Settings Menu - Pointer Shape
    Settings Menu - Test Pattern
    Settings Menu - User Button
    Extended Menu - User's Logo
    Extended Menu - Language
    Extended Menu - Operation - High Altitude Mode
    Extended Menu - Operation - Lens Cover Timer
    Reset Menu - Reset All and Reset Lamp Hours

    When Web Control Password is set in the Network menu from the
    projector's Configuration menu, the password entry screen is
    displayed.

    Displaying the Web Remote screen
    The Web Remote function allows you to perform projector remote control
    operations with a Web browser.

    a

    Display the Web Control screen.



  • Page 112

    Monitoring and Controlling (EB-1775W/EB-1770W/EB-1760W Only)

    b

    c

    Click Web Remote.

    Name

    112

    Function

    E [A/V Mute] button

    Turns the video and audio on or off.
    s "Hiding the Image and Sound Temporarily (A/V
    Mute)" p.51

    F [Page] buttons
    [Up] [Down]

    Changes pages in files such as PowerPoint files when using
    the following projection methods.
    • When using the Wireless Mouse function
    s "Using the Remote Control to Operate the
    Mouse Pointer (Wireless Mouse)" p.54
    • When using USB Display
    s "Projecting with USB Display" p.28
    • During a network connection (EB-1775W/EB-1770W/
    EB-1760W only)

    The Web Remote screen is displayed.

    When projecting images or scenarios using Slideshow,
    pressing these buttons displays the previous/next screen.

    Name

    Changes to the next input source that is sending an image.
    s "Automatically Detect Input Signals and Change the
    Projected Image (Source Search)" p.27

    H [LAN] button

    Changes to the image projected with EasyMP Network
    Projection. When projecting using the supplied or
    optional Quick Wireless Connection USB Key, this button
    switches to that image. (EB-1775W/EB-1770W/
    EB-1760W only)
    s "Switching to the Target Image by Remote Control"
    p.28

    I [USB] button

    Each time the button is pressed, it cycles through the
    following images:
    • USB Display
    • Images from the device connected to the USB port
    s "Switching to the Target Image by Remote Control"
    p.28

    J [Volume] buttons
    [a][b]

    [a] Decreases the volume.
    [b] Increases the volume.
    s "Adjusting the Volume" p.38

    Function

    A [t] button

    Turns the projector power on or off.
    s "From Installation to Projection" p.26

    B [Computer] button

    Changes to images from the Computer port.

    C [Video] button

    Each time you press the button, the input source changes
    between images from the Video port and the HDMI port
    (EB-1775W/EB-1770W/EB-1760W only).

    D [Freeze] button

    G [Source Search]
    button

    Images are paused or unpaused.
    s "Freezing the Image (Freeze)" p.52



  • Page 113

    Monitoring and Controlling (EB-1775W/EB-1770W/EB-1760W Only)

    Using the Mail Notification Function to Report
    Problems
    When you set Mail Notification, notification messages are sent to the preset
    email addresses when a problem or warning occurs with a projector. This
    will enable the operator to be notified of problems with projectors even at
    locations away from the projectors.
    s Network - Mail - Mail Notification p.82

    a

    • Up to a maximum of three notification destinations (addresses) can
    be registered, and notification messages can be sent to all three
    destinations at once.
    • If a projector develops a critical problem and suddenly stops
    working, it may not be able to send a message notifying an operator
    of the problem.
    • If you set Standby Mode to Communication On, you can control
    the projector even if it is in standby mode (when the power is
    off).
    s Extended - Standby Mode p.74

    Reading Error Notification Mail
    When the Mail Notification function is set to On and a problem or warning
    occurs in the projector, the following email will be sent.
    Subject: EPSON Projector
    Line 1: The projector name where the problem has occurred
    Line 2: The IP address set for the projector where the problem has
    occurred.
    Line 3 and on: Details of the problem
    The following messages are listed line by line to indicate the details of the
    problem. See the following to deal with problems or warnings.

    113

    s "Reading the Indicators" p.88

    • Internal error
    • Fan related error
    • Sensor error
    • Lamp timer failure
    • Lamp out
    • Internal temperature error
    • High-speed cooling in progress
    • Lamp replacement notification
    • No-signal
    • Auto Iris Error
    • Power Err. (Ballast)
    A (+) or (-) appears at the start of the message.
    (+): A projector problem has occurred
    (-): A projector problem has been dealt with

    Management Using SNMP
    By setting SNMP to On, notification messages are sent to preset email
    addresses when a problem or warning occurs. This will enable the operator
    to be notified of problems with projectors even at locations away from the
    projectors.
    s Network - Others - SNMP p.82

    a

    • SNMP should be managed by a network administrator or someone
    who is familiar with the network.
    • To use the SNMP function to monitor the projector, you need to
    install the SNMP manager program on your computer.
    • The managing function using SNMP cannot be used via wireless
    LAN in Quick connection mode.
    • Up to two destination IP addresses can be saved.



  • Page 114

    Monitoring and Controlling (EB-1775W/EB-1770W/EB-1760W Only)

    ESC/VP21 Commands
    You can monitor and control the projector from a computer via USB.
    Connect the device and the projector with a USB cable, and then enter the
    communication commands (ESC/VP21 commands).

    When a command is input, the projector executes the command and
    returns a ":", and then accepts the next command.
    If the command being processed terminates abnormally, an error message is
    output and a ":" is returned.
    Item
    Power ON/OFF

    Before starting
    To control and monitor the projector using ESC/VP21 commands, the
    following preparations must be carried out.

    a
    b

    d

    Signal selection

    Command

    On

    PWR ON

    Off

    PWR OFF

    Computer

    Auto

    SOURCE 1F

    RGB

    SOURCE 11

    Component

    SOURCE 14

    Install the USB communication driver (EPSON USB-COM Driver) to
    your computer. For information about the EPSON USB-COM Driver,
    contact your local dealer or the nearest address provided in the
    Epson Projector Contact List.

    HDMI (EB-1775W/EB-1770W/
    EB-1760W only)

    SOURCE 30

    Video

    SOURCE 41

    s Epson Projector Contact List

    USB Display

    SOURCE 51

    USB

    SOURCE 52

    Set USB Type B to Link 21L from the projector's Configuration
    menu.
    s Extended - USB Type B p.74

    c

    114

    LAN (EB-1775W/EB-1770W/EB-1760W SOURCE 53
    only)
    A/V Mute On/Off

    Set Link 21L to On.
    s Extended - Link 21L p.74

    Connect the computer's USB port to the projector's USB (Type B)
    port with a USB cable.
    Start from step 2 from the second time.

    Command list
    When the power ON command is transmitted to the projector, the power
    turns on and it enters warm-up mode. When the projector's power has
    turned on, a colon ":" (3Ah) is returned.

    A/V Mute selection

    On

    MUTE ON

    Off

    MUTE OFF

    Black

    MSEL 00

    Blue

    MSEL 01

    Logo

    MSEL 02

    Add a Carriage Return (CR) code (0Dh) to the end of each command and
    transmit.

    Communications protocol
    • Default baud rate setting: 9600 bps
    • Data length: 8 bit
    • Parity: None



  • Page 115

    Monitoring and Controlling (EB-1775W/EB-1770W/EB-1760W Only)

    • Stop-bit: 1 bit
    • Flow control: None

    115



  • Page 116

    About Event ID (EB-1775W/EB-1770W/EB-1760W Only)

    116

    Check the numbers and then apply the following countermeasures. If you cannot resolve the problem, contact your network administrator, or contact your local
    dealer or the nearest address provided in the Epson Projector Contact List.
    s Epson Projector Contact List
    Event ID

    Cause

    Remedy

    0432
    0435

    Failed to startup EasyMP Network Projection.

    Restart the projector.

    0434
    0482
    0484
    0485

    Network communication is unstable.

    Check the network communication status, and reconnect after waiting for a
    while.

    0433

    Cannot play transferred images.

    Restart EasyMP Network Projection.

    0481

    Communication was disconnected from the computer.

    0483
    04FE

    EasyMP Network Projection ended unexpectedly.

    Check the network communication status, and then restart the projector.

    0479
    04FF

    A system error occurred in the projector.

    Restart the projector.

    0891

    Cannot find an access point with the same SSID.

    Set the computer, the access point, and the projector to the same SSID.

    0892

    The WPA/WPA2 authentication type does not match.

    0893

    The WEP/TKIP/AES encryption type does not match.

    Check that the wireless LAN security settings are correct.
    s Security p.80

    0894

    Communication was disconnected because the projector connected to an
    unauthorized access point.

    Contact your network administrator for more information.

    0898

    Failed to acquire DHCP.

    Check that the DHCP server is operating correctly. If you are not using DHCP,
    turn off the DHCP setting.
    s Wireless LAN - IP Settings p.79

    0895
    0899

    Other communication errors

    If restarting the projector or EasyMP Network Projection does not solve the
    problem, contact your local dealer or the nearest address provided in the Epson
    Projector Contact List.
    s Epson Projector Contact List



  • Page 117

    About PJLink (EB-1775W/EB-1770W/EB-1760W Only)
    PJLink Class1 was established by the JBMIA (Japan Business Machine and
    Information System Industries Association) as a standard protocol for
    controlling network-compatible projector's as part of their efforts to
    standardize projector control protocols.
    The projector complies with the PJLink Class1 standard established by the
    JBMIA.
    It complies with all commands except for the following commands defined
    by PJLink Class1, and agreement was confirmed by the PJLink standard
    adaptability verification.
    URL: http://pjlink.jbmia.or.jp/english/
    • Non-compatible commands
    Function
    Mute settings

    PJLink Command

    Image muting set

    AVMT 11

    Audio muting set

    AVMT 21

    • Input names defined by PJLink and corresponding projector sources
    Source

    PJLink Command

    Computer

    INPT 11

    Video

    INPT 21

    HDMI

    INPT 32

    USB

    INPT 41

    LAN

    INPT 52

    USB Display

    INPT 53

    • Manufacturer name displayed for "Manufacture name information query"
    EPSON

    • Model name displayed for "Product name information query"
    EB-1775W/PowerLite 1775W/EB-C300MS
    EB-1770W/PowerLite 1770W/EB-C300MN/EB-C3010WN
    EB-1760W/PowerLite 1760W/EB-C260MN

    117



  • Page 118

    Screen Size and Projection Distance

    118

    Projection Distance (For EB-1775W/EB-1770W/
    EB-1760W)

    A
    4:3 Screen Size

    Minimum (Wide) to Maximum
    (Tele)

    B

    40"

    81x61

    102 - 122

    -6

    50"

    100x76

    127 - 153

    -7

    60"

    120x91

    153 - 184

    -8

    80"

    160x120

    205 - 246

    -11

    100"

    200x150

    256 - 308

    -14

    150"

    300x230

    385 - 462

    -21

    200"

    410x300

    514 - 617

    -28

    250"

    500x380

    643 - 771

    -35

    260"

    520x400

    668 - 802

    -36

    Unit: cm
    A
    16:9 Screen Size

    A Projection distance
    B Distance from the center of the lens to the base of the screen
    (or to the top of the screen, if suspended from a ceiling)
    C Center of lens

    Unit: cm
    A
    4:3 Screen Size

    Minimum (Wide) to Maximum
    (Tele)

    B

    28"

    57x43

    71 - 85

    -4

    30"

    61x46

    76 - 91

    -4

    Minimum (Wide) to Maximum
    (Tele)

    B

    30"

    66x37

    69 - 83

    -2

    40"

    89x50

    92 - 111

    -2

    50"

    110x62

    115 - 139

    -3

    60"

    130x75

    139 - 167

    -3

    70"

    160x87

    162 - 195

    -4

    80"

    180x100

    186 - 223

    -5

    100"

    220x120

    232 - 279

    -6

    150"

    330x190

    349 - 419

    -8

    200"

    440x250

    466 - 560

    -11

    250"

    550x310

    583 - 700

    -14

    280"

    620x350

    653 - 784

    -16



  • Page 119

    Screen Size and Projection Distance

    119

    Unit: cm
    A
    16:10 Screen Size

    Minimum (Wide) to Maximum
    (Tele)

    B

    30"

    64x40

    67 - 80

    -4

    40"

    86x54

    89 - 108

    -5

    50"

    110x67

    112 - 135

    -6

    60"

    130x81

    135 - 162

    -7

    80"

    170x110

    181 - 217

    -10

    100"

    220x130

    226 - 271

    -12

    150"

    320x200

    340 - 408

    -18

    200"

    430x270

    454 - 545

    -24

    250"

    540x340

    567 - 681

    -31

    300"

    640x400

    681 - 818

    -37

    Projection Distance (For EB-1750)

    A Projection distance
    B Distance from the center of the lens to the base of the screen
    (or to the top of the screen, if suspended from a ceiling)
    C Center of lens

    Unit: cm
    A
    4:3 Screen Size

    Minimum (Wide) to Maximum
    (Tele)

    B

    30"

    61x46

    72 - 86

    -5

    40"

    81x61

    96 - 116

    -7

    50"

    100x76

    120 - 145

    -9



  • Page 120

    Screen Size and Projection Distance

    120

    A
    4:3 Screen Size

    Minimum (Wide) to Maximum
    (Tele)

    B

    60"

    120x91

    145 - 174

    -10

    80"

    160x120

    194 - 233

    -14

    100"

    200x150

    242 - 291

    -17

    150"

    300x230

    364 - 438

    -26

    200"

    410x300

    486 - 584

    -34

    250"

    510x380

    608 - 730

    -43

    300"

    610x460

    730 - 877

    -51

    Unit: cm
    A
    16:9 Screen Size

    Minimum (Wide) to Maximum
    (Tele)

    B

    30"

    66x37

    78 - 94

    +1

    40"

    89x50

    105 - 126

    +1

    50"

    110x62

    131 - 158

    +1

    60"

    130x75

    158 - 190

    +1

    70"

    160x87

    185 - 222

    +1

    80"

    180x100

    211 - 254

    +2

    100"

    220x120

    264 - 317

    +2

    150"

    330x190

    397 - 477

    +3

    200"

    440x250

    530 - 636

    +4

    250"

    550x310

    663 - 796

    +5

    275"

    610x340

    729 - 875

    +6



  • Page 121

    Supported Monitor Displays

    121

    Component video

    Supported Resolutions
    Computer signals (analog RGB)

    Signal

    Refresh Rate (Hz)

    Resolution (dots)

    SDTV (480i)

    60

    720x480

    Signal

    Refresh Rate (Hz)

    Resolution (dots)

    SDTV (576i)

    50

    720x576

    VGA

    60/72/75/85

    640x480

    SDTV (480p)

    60

    720x480

    SVGA

    56/60/72/75/85

    800x600

    SDTV (576p)

    50

    720x576

    XGA

    60/70/75/85

    1024x768

    HDTV (720p)

    50/60

    1280x720

    WXGA

    60

    1280x768

    HDTV (1080i)

    50/60

    1920x1080

    60

    1360x768

    HDTV (1080p)

    24/30/50/60

    1920x1080

    60/75/85

    1280x800

    WXGA+

    60/75/85

    1440x900

    SXGA

    70/75/85

    1152x864

    60/75/85

    1280x1024

    Signal

    Refresh Rate (Hz)

    Resolution (dots)

    60/75/85

    1280x960

    TV (NTSC)

    60

    720x480

    60/75

    1400x1050

    TV (SECAM)

    50

    720x576

    60

    1680x1050

    TV (PAL)

    50/60

    720x576

    UXGA

    60

    1600x1200

    MAC13"

    67

    640x480

    MAC16"

    75

    832x624

    MAC19"

    75

    1024x768

    Signal

    Refresh Rate (Hz)

    Resolution (dots)

    59

    1024x768

    VGA

    60

    640x480

    75

    1152x870

    SVGA

    60

    800x600

    XGA

    60

    1024x768

    WXGA

    60

    1280x800

    60

    1280x960

    60

    1280x1024

    60

    1400x1050

    SXGA+
    WSXGA+*1,

    MAC21"

    2

    *1 (EB-1775W/EB-1770W/EB-1760W only)
    *2 Only compatible when Wide is selected as the Resolution from the
    Configuration menu.
    Even when signals other than those mentioned above are input, it is likely that the
    image can be projected. However, not all functions may be supported.

    Composite video

    Input signal from the HDMI port (EB-1775W/EB-1770W/EB-1760W
    only)

    SXGA
    SXGA+



  • Page 122

    Supported Monitor Displays

    122

    Signal

    Refresh Rate (Hz)

    Resolution (dots)

    UXGA

    60

    1600x1200

    SDTV (480i/480p)

    60

    720x480

    SDTV (576i/576p)

    50

    720x576

    HDTV (720p)

    50/60

    1280x720

    HDTV (1080i)

    50/60

    1920x1080

    HDTV (1080p)

    24/30/50/60

    1920x1080



  • Page 123

    Specifications

    123

    Projector General Specifications
    EB-1775W

    Product name

    EB-1770W

    EB-1760W

    292 (W) x 44 (H) x 210 (D) mm (not including raised section)

    Dimensions

    0.59" Wide

    LCD panel size

    0.55"

    Polysilicon TFT active matrix

    Display method

    1,024,000 pixels
    WXGA (1280 (W)x 800 (H) dots)x 3

    Resolution

    Focus adjustment

    Electric/Auto
    Manual (1 to 1.2)
    UHE lamp, 230 W Model No.: ELPLP65

    Lamp

    786,432 pixels
    XGA (1024 (W) x 768 (H)
    dots)x 3
    Manual

    Zoom adjustment

    UHE lamp, 205 W Model No.:
    ELPLP65

    UHE lamp, 230 W Model No.:
    ELPLP65

    1 W monaural

    Max. audio output

    1

    Speaker
    100 to 240 V AC ±10%, 50/60 Hz 3.3 to 1.5 A

    Power supply
    Power con‐
    sumption

    EB-1750

    100 to 240 V AC ±10%, 50/60
    Hz 3.0 to 1.4 A

    100 to 240 V AC ±10%, 50/60
    Hz 3.3 to 1.5 A

    100 to 120 V area

    Operating: 322 W
    Standby power consumption (Communication On): 7.4 W
    Standby power consumption (Communication Off): 0.38 W

    Operating: 293 W
    Standby power consumption
    (Communication On): 7.4 W
    Standby power consumption
    (Communication Off): 0.38 W

    Operating: 322 W
    Standby power consumption
    (Communication On): 7.4 W
    Standby power consumption
    (Communication Off): 0.38 W

    220 to 240 V area

    Operating: 304 W
    Standby power consumption (Communication On): 7.7 W
    Standby power consumption (Communication Off): 0.44 W

    Operating: 278 W
    Standby power consumption
    (Communication On): 7.7 W
    Standby power consumption
    (Communication Off): 0.44 W

    Operating: 304 W
    Standby power consumption
    (Communication On): 7.7 W
    Standby power consumption
    (Communication Off): 0.44 W

    Operating altitude
    Operating temperature
    Storage temperature

    Altitude 0 to 2,286 m
    5 to +35°C (No condensation)
    -10 to +60°C (No condensation)



  • Page 124

    Specifications

    124

    Approx. 1.7 kg

    Mass
    EB-1775W

    Product name
    Con‐
    nec‐
    tors

    EB-1770W

    EB-1760W

    Computer port

    1

    Mini D-Sub15-pin (female)

    Video port

    1

    RCA pin jack

    Audio port

    1

    Stereo mini jack

    HDMI port

    1

    USB (TypeA) Port *

    1

    USB connector (Type A)

    USB (TypeB) Port *

    1

    USB connector (Type B)

    USB port
    (dedicated Wireless LAN
    unit)

    HDMI (Audio is only supported by PCM)

    EB-1750

    -

    -

    1

    USB connector (Type A)

    * Supports USB 2.0. However, USB ports are not guaranteed to operate all devices that support USB.



  • Page 125

    Specifications

    125

    This product is also designed for IT power distribution system with phase-to-phase voltage 230V.
    Angle of tilt

    30

    30

    If you use the projector tilted at an angle of more than 30˚ it could be damaged and cause an accident.



  • Page 126

    Specifications

    126

    DECLARATION of CONFORMITY
    According to 47CFR, Part 2 and 15
    Class B Personal Computers and Peripherals; and/or
    CPU Boards and Power Supplies used with Class B Personal Computers
    We:
    Located at:

    Tel:

    Epson America, Inc.
    3840 Kilroy Airport Way
    MS: 3-13
    Long Beach, CA 90806
    562-290-5254

    Declare under sole responsibility that the product identified herein,
    complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital
    device. Each product marketed, is identical to the representative unit tested
    and found to be compliant with the standards. Records maintained continue
    to reflect the equipment being produced can be expected to be within the
    variation accepted, due to quantity production and testing on a statistical
    basis as required by 47CFR 2.909. Operation is subject to the following two
    conditions : (1) this device may not cause harmful interference, and (2) this
    device must accept any interference received, including interference that
    may cause undesired operation.
    Trade Name:

    EPSON

    Type of Product:

    Projector

    Model:

    H361C/H362C/H363C/H372C

    FCC Compliance Statement
    For United States Users

    This equipment has been tested and found to comply with the limits for a
    Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
    are designed to provide reasonable protection against harmful interference
    in a residential installation. This equipment generates, uses, and can radiate
    radio frequency energy and, if not installed and used in accordance with the
    instructions, may cause harmful interference to radio or television
    reception. However, there is no guarantee that interference will not occur in
    a particular installation. If this equipment does cause interference to radio
    and television reception, which can be determined by turning the
    equipment off and on, the user is encouraged to try to correct the
    interference by one or more of the following measures.
    • Reorient or relocate the receiving antenna.
    • Increase the separation between the equipment and receiver.
    • Connect the equipment into an outlet on a circuit different from that to
    which the receiver is connected.
    • Consult the dealer or an experienced radio/TV technician for help.
    WARNING

    The connection of a non-shielded equipment interface cable to this
    equipment will invalidate the FCC Certification or Declaration of this
    device and may cause interference levels which exceed the limits established
    by the FCC for this equipment. It is the responsibility of the user to obtain
    and use a shielded equipment interface cable with this device. If this
    equipment has more than one interface connector, do not leave cables
    connected to unused interfaces. Changes or modifications not expressly
    approved by the manufacturer could void the user's authority to operate the
    equipment.



  • Page 127

    Appearance

    127

    292

    3

    28.6

    50.4

    107.5

    Center of lens
    Distance from center of lens to suspension bracket fixing point

    210

    148

    42

    38

    A
    B

    100

    52.5

    222

    Units: mm



  • Page 128

    Glossary

    128

    This section briefly explains the difficult terms that are not explained in the text of this guide. For details, refer to other commercially available publications.
    AMX Device Discovery

    AMX Device Discovery is a technology developed by AMX to facilitate AMX control systems for easy operation of the target equipment.
    Epson have implemented this protocol technology, and have provided a setting to enable the protocol function (ON).
    See the AMX Web site for more details.
    URL http://www.amx.com/

    Aspect Ratio

    The ratio between an image's length and its height. Screens with a horizontal:vertical ratio of 16:9, such as HDTV screens, are known as wide screens.
    SDTV and general computer displays have an aspect ratio of 4:3.

    Component Video

    A method that separates the video signal into a luminance component (Y), and a blue minus luminance (Cb or Pb) and a red minus luminance (Cr or
    Pr).

    Composite video

    A method that combines the video signal into a luminance component and a color component for transmission down a single cable.

    Contrast

    The relative brightness of the light and dark areas of an image can be increased or decreased to make text and graphics stand out more clearly, or to
    make them appear softer. Adjusting this particular property of an image is called contrast adjustment.

    DHCP

    An abbreviation of Dynamic Host Configuration Protocol, this protocol automatically assigns an IP addressg to equipment connected to a network.

    Gateway Address

    This is a server (router) for communicating across a network (subnet) divided according to subnet maskg.

    HDCP

    HDCP is an abbreviation for High-bandwidth Digital Content Protection. It is used to prevent illegal copying and protect copyrights by encrypting
    digital signals sent over DVI and HDMI ports. Because the HDMI port on this projector supports HDCP, it can project digital images protected by
    HDCP technology. However, the projector may not be able to project images protected with updated or revised versions of HDCP encryption.

    HDTV

    An abbreviation for High-Definition Television that refers to high-definition systems which satisfy the following conditions.
    • Vertical resolution of 720p or 1080i or greater (p = Progressiveg, i = Interlaceg)
    • Screen aspect ratiog of 16:9

    Interlace

    Transmits information needed to create one screen by sending every other line, starting from the top of the image and working down to the bottom.
    Images are more likely to flicker because one frame is displayed every other line.

    IP Address

    A number to identify a computer connected to a network.

    Progressive

    Projects information to create one screen at a time, displaying the image for one frame. Even though the number of scan lines is the same, the amount
    of flicker in images decreases because the volume of information has doubled compared with an interlace system.

    SDTV

    An abbreviation for Standard Definition Television that refers to standard television systems which do not satisfy the conditions for HDTVg HighDefinition Television.

    SNMP

    An abbreviation for Simple Network Management Protocol, which is the protocol for monitoring and controlling devices such as routers and
    computers connected to a TCP/IP network.



  • Page 129

    Glossary

    129

    sRGB

    An international standard for color intervals that was formulated so that colors that are reproduced by video equipment can be handled easily by
    computer operating systems (OS) and the Internet. If the connected source has an sRGB mode, set both the projector and the connected signal source
    to sRGB.

    SSID

    SSID is identification data for connecting to another device on a wireless LAN. Wireless communication is possible between devices with matching
    SSID.

    Subnet Mask

    This is a numerical value that defines the number of bits used for the network address on a divided network (subnet) from the IP address.

    SVGA

    A screen size standard with a resolution of 800 (horizontal) x 600 (vertical) dots.

    S-Video

    A method that separates the video signal into a luminance component (Y) and a color component (C).

    SXGA

    A screen size standard with a resolution of 1,280 (horizontal) x 1,024 (vertical) dots.

    Sync.

    The signals output from computers have a specific frequency. If the projector frequency does not match this frequency, the resulting images are not of
    a good quality. The process of matching the phases of these signals (the relative position of the crests and the troughs in the signal) is called
    Synchronization. If the signals are not synchronized, flickering, blurriness, and horizontal interference occur.

    Tracking

    The signals output from computers have a specific frequency. If the projector frequency does not match this frequency, the resulting images are not of
    a good quality. The process of matching the frequency of these signals (the number of crests in the signal) is called Tracking. If Tracking is not carried
    out correctly, wide vertical stripes appear in the signal.

    Trap IP Address

    This is the IP addressg for the destination computer used for error notification in SNMP.

    VGA

    A screen size standard with a resolution of 640 (horizontal) x 480 (vertical) dots.

    XGA

    A screen size standard with a resolution of 1,024 (horizontal) x 768 (vertical) dots.



  • Page 130

    General Notes

    130

    All rights reserved. No part of this publication may be reproduced, stored in a retrieval
    system, or transmitted in any form or by any means, electronic, mechanical,
    photocopying, recording, or otherwise, without the prior written permission of Seiko
    Epson Corporation. No patent liability is assumed with respect to the use of the
    information contained herein. Neither is any liability assumed for damages resulting
    from the use of the information contained herein.
    Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this
    product or third parties for damages, losses, costs, or expenses incurred by the
    purchaser or third parties as a result of: accident, misuse, or abuse of this product or
    unauthorized modifications, repairs, or alterations to this product, or (excluding the
    U.S.) failure to strictly comply with Seiko Epson Corporation's operating and
    maintenance instructions.
    Seiko Epson Corporation shall not be liable against any damages or problems arising
    from the use of any options or any consumable products other than those designated as
    Original Epson Products or Epson Approved Products by Seiko Epson Corporation.
    The contents of this guide may be changed or updated without further notice.
    Illustrations in this guide and the actual projector may differ.

    About Notations
    Microsoft
    Microsoft
    Microsoft
    Microsoft
    Microsoft
    Microsoft
    Microsoft

    ®
    ®
    ®
    ®
    ®
    ®
    ®

    ®
    ®
    ®
    ®
    ®
    ®
    ®

    Windows 98 operating system
    Windows Me operating system
    Windows 2000 operating system
    Windows XP Professional operating system
    Windows XP Home Edition operating system
    Windows Vista operating system
    Windows 7 operating system

    In this guide, the operating systems above are referred to as "Windows 98",
    Windows Me", "Windows 2000", "Windows XP", "Windows Vista", and
    "Windows 7". Furthermore, the collective term Windows may be used to
    refer to Windows 98, Windows Me, Windows 2000, Windows XP,

    Windows Vista, and Windows 7, and multiple versions of Windows may be
    referred to as, for example, Windows 98/Me/2000/XP/Vista, with the
    Windows notation omitted.
    Mac
    Mac
    Mac
    Mac

    OS
    OS
    OS
    OS

    X
    X
    X
    X

    10.3.x
    10.4.x
    10.5.x
    10.6.x

    In this guide, the operating systems above are referred to as "Mac OS X
    10.3.9", "Mac OS X 10.4.x", "Mac OS X 10.5.x", and "Mac OS X 10.6.x".
    Furthermore, the collective term "Mac OS" is used to refer to them.

    General Notice:
    IBM, DOS/V, and XGA are trademarks or registered trademarks of International
    Business Machines Corporation.
    Macintosh, Mac, Mac OS, and iMac are trademarks of Apple Inc.
    Microsoft, Windows, Windows NT, Windows Vista, Windows 7, PowerPoint, and
    Windows logo are trademarks or registered trademarks of Microsoft Corporation in the
    United States and/or other countries.
    WPA and WPA2 are registered trademarks of Wi-Fi Alliance.
    HDMI and High-Definition Multimedia Interface are the trademarks or registered





    trademarks of HDMI Licensing LLC.
    PJLink trademark is a trademark applied for registration or is already registered in
    Japan, the United States of America and other countries and areas.
    Other product names used herein are also for identification purposes only and may be
    trademarks of their respective owners. Epson disclaims any and all rights in those
    marks.

    ©SEIKO EPSON CORPORATION 2010. All rights reserved.



  • Page 131

    General Notes

    GNU GPL
    This projector product includes the open source software programs which apply
    the GNU General Public License Version 2 or later version ("GPL Programs").
    We provide the source code of the GPL Programs until five (5) years after the
    discontinuation of same model of this projector product.
    If you desire to receive the source code of the GPL Programs, please see the
    "EPSON Projector Contact List" in the User's Guide, and contact the customer
    support of your region.
    These GPL Programs are WITHOUT ANY WARRANTY; without even the
    implied warranty of MERCHANTABILITY AND FITNESS FOR A
    PARTICULAR PURPOSE. See the GNU General Public License for more details.
    The list of GPL Programs is as follows and the names of author are described in the
    source code of the GPL Programs
    The list of GPL Programs
    busybox-1.13.4
    iptables-1.4.2
    libgcc1(gcc-4.3.3)
    linux-2.6.27
    patches
    udhcp 0.9.8
    uvc rev.219
    wireless_tools 29
    EPSON original drivers
    The GNU General Public License Version 2 is as follows. You also can see the GNU
    General Public License Version 2 at http://www.gnu.org/licenses/.
    GNU GENERAL PUBLIC LICENSE
    Version 2, June 1991
    Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth
    Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute
    verbatim copies of this license document, but changing it is not allowed.
    Preamble

    131

    The licenses for most software are designed to take away your freedom to share and
    change it. By contrast, the GNU General Public License is intended to guarantee your
    freedom to share and change free software--to make sure the software is free for all its
    users. This General Public License applies to most of the Free Software Foundation's
    software and to any other program whose authors commit to using it. (Some other Free
    Software Foundation software is covered by the GNU Lesser General Public License
    instead.) You can apply it to your programs, too.
    When we speak of free software, we are referring to freedom, not price. Our General
    Public Licenses are designed to make sure that you have the freedom to distribute copies
    of free software (and charge for this service if you wish), that you receive source code or
    can get it if you want it, that you can change the software or use pieces of it in new free
    programs; and that you know you can do these things.
    To protect your rights, we need to make restrictions that forbid anyone to deny you
    these rights or to ask you to surrender the rights. These restrictions translate to certain
    responsibilities for you if you distribute copies of the software, or if you modify it.
    For example, if you distribute copies of such a program, whether gratis or for a fee, you
    must give the recipients all the rights that you have. You must make sure that they, too,
    receive or can get the source code. And you must show them these terms so they know
    their rights.
    We protect your rights with two steps: (1) copyright the software, and (2) offer you this
    license which gives you legal permission to copy, distribute and/or modify the software.
    Also, for each author's protection and ours, we want to make certain that everyone
    understands that there is no warranty for this free software. If the software is modified
    by someone else and passed on, we want its recipients to know that what they have is not
    the original, so that any problems introduced by others will not reflect on the original
    authors' reputations.
    Finally, any free program is threatened constantly by software patents. We wish to avoid
    the danger that redistributors of a free program will individually obtain patent licenses,
    in effect making the program proprietary. To prevent this, we have made it clear that any
    patent must be licensed for everyone's free use or not licensed at all.
    The precise terms and conditions for copying, distribution and modification follow.



  • Page 132

    General Notes

    GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING,
    DISTRIBUTION AND MODIFICATION
    0. This License applies to any program or other work which contains a notice placed
    by the copyright holder saying it may be distributed under the terms of this
    General Public License. The "Program", below, refers to any such program or
    work, and a "work based on the Program" means either the Program or any
    derivative work under copyright law: that is to say, a work containing the Program
    or a portion of it, either verbatim or with modifications and/or translated into
    another language. (Hereinafter, translation is included without limitation in the
    term "modification".) Each licensee is addressed as "you".
    Activities other than copying, distribution and modification are not covered by
    this License; they are outside its scope. The act of running the Program is not
    restricted, and the output from the Program is covered only if its contents
    constitute a work based on the Program (independent of having been made by
    running the Program). Whether that is true depends on what the Program does.
    1. You may copy and distribute verbatim copies of the Program's source code as you
    receive it, in any medium, provided that you conspicuously and appropriately
    publish on each copy an appropriate copyright notice and disclaimer of warranty;
    keep intact all the notices that refer to this License and to the absence of any
    warranty; and give any other recipients of the Program a copy of this License along
    with the Program.
    You may charge a fee for the physical act of transferring a copy, and you may at
    your option offer warranty protection in exchange for a fee.
    2. You may modify your copy or copies of the Program or any portion of it, thus
    forming a work based on the Program, and copy and distribute such modifications
    or work under the terms of Section 1 above, provided that you also meet all of these
    conditions:
    a) You must cause the modified files to carry prominent notices stating that you
    changed the files and the date of any change.
    b) You must cause any work that you distribute or publish, that in whole or in
    part contains or is derived from the Program or any part thereof, to be
    licensed as a whole at no charge to all third parties under the terms of this
    License.

    132

    c)

    3.

    If the modified program normally reads commands interactively when run,
    you must cause it, when started running for such interactive use in the most
    ordinary way, to print or display an announcement including an appropriate
    copyright notice and a notice that there is no warranty (or else, saying that
    you provide a warranty) and that users may redistribute the program under
    these conditions, and telling the user how to view a copy of this License.
    (Exception: if the Program itself is interactive but does not normally print
    such an announcement, your work based on the Program is not required to
    print an announcement.)
    These requirements apply to the modified work as a whole. If identifiable sections
    of that work are not derived from the Program, and can be reasonably considered
    independent and separate works in themselves, then this License, and its terms, do
    not apply to those sections when you distribute them as separate works. But when
    you distribute the same sections as part of a whole which is a work based on the
    Program, the distribution of the whole must be on the terms of this License, whose
    permissions for other licensees extend to the entire whole, and thus to each and
    every part regardless of who wrote it.
    Thus, it is not the intent of this section to claim rights or contest your rights to work
    written entirely by you; rather, the intent is to exercise the right to control the
    distribution of derivative or collective works based on the Program.
    In addition, mere aggregation of another work not based on the Program with the
    Program (or with a work based on the Program) on a volume of a storage or
    distribution medium does not bring the other work under the scope of this
    License.
    You may copy and distribute the Program (or a work based on it, under Section 2)
    in object code or executable form under the terms of Sections 1 and 2 above
    provided that you also do one of the following:
    a) Accompany it with the complete corresponding machine-readable source
    code, which must be distributed under the terms of Sections 1 and 2 above on
    a medium customarily used for software interchange; or,
    b) Accompany it with a written offer, valid for at least three years, to give any
    third party, for a charge no more than your cost of physically performing
    source distribution, a complete machine-readable copy of the corresponding
    source code, to be distributed under the terms of Sections 1 and 2 above on a
    medium customarily used for software interchange; or,



  • Page 133

    General Notes

    c)

    4.

    5.

    6.

    Accompany it with the information you received as to the offer to distribute
    corresponding source code. (This alternative is allowed only for
    noncommercial distribution and only if you received the program in object
    code or executable form with such an offer, in accord with Subsection b
    above.)
    The source code for a work means the preferred form of the work for making
    modifications to it. For an executable work, complete source code means all the
    source code for all modules it contains, plus any associated interface definition
    files, plus the scripts used to control compilation and installation of the executable.
    However, as a special exception, the source code distributed need not include
    anything that is normally distributed (in either source or binary form) with the
    major components (compiler, kernel, and so on) of the operating system on which
    the executable runs, unless that component itself accompanies the executable.
    If distribution of executable or object code is made by offering access to copy from
    a designated place, then offering equivalent access to copy the source code from
    the same place counts as distribution of the source code, even though third parties
    are not compelled to copy the source along with the object code.
    You may not copy, modify, sublicense, or distribute the Program except as
    expressly provided under this License. Any attempt otherwise to copy, modify,
    sublicense or distribute the Program is void, and will automatically terminate your
    rights under this License. However, parties who have received copies, or rights,
    from you under this License will not have their licenses terminated so long as such
    parties remain in full compliance.
    You are not required to accept this License, since you have not signed it. However,
    nothing else grants you permission to modify or distribute the Program or its
    derivative works. These actions are prohibited by law if you do not accept this
    License. Therefore, by modifying or distributing the Program (or any work based
    on the Program), you indicate your acceptance of this License to do so, and all its
    terms and conditions for copying, distributing or modifying the Program or works
    based on it.
    Each time you redistribute the Program (or any work based on the Program), the
    recipient automatically receives a license from the original licensor to copy,
    distribute or modify the Program subject to these terms and conditions. You may
    not impose any further restrictions on the recipients' exercise of the rights granted
    herein. You are not responsible for enforcing compliance by third parties to this
    License.

    133

    7.

    8.

    9.

    If, as a consequence of a court judgment or allegation of patent infringement or for
    any other reason (not limited to patent issues), conditions are imposed on you
    (whether by court order, agreement or otherwise) that contradict the conditions of
    this License, they do not excuse you from the conditions of this License. If you
    cannot distribute so as to satisfy simultaneously your obligations under this
    License and any other pertinent obligations, then as a consequence you may not
    distribute the Program at all. For example, if a patent license would not permit
    royalty-free redistribution of the Program by all those who receive copies directly
    or indirectly through you, then the only way you could satisfy both it and this
    License would be to refrain entirely from distribution of the Program.
    If any portion of this section is held invalid or unenforceable under any particular
    circumstance, the balance of the section is intended to apply and the section as a
    whole is intended to apply in other circumstances.
    It is not the purpose of this section to induce you to infringe any patents or other
    property right claims or to contest validity of any such claims; this section has the
    sole purpose of protecting the integrity of the free software distribution system,
    which is implemented by public license practices. Many people have made
    generous contributions to the wide range of software distributed through that
    system in reliance on consistent application of that system; it is up to the author/
    donor to decide if he or she is willing to distribute software through any other
    system and a licensee cannot impose that choice.
    This section is intended to make thoroughly clear what is believed to be a
    consequence of the rest of this License.
    If the distribution and/or use of the Program is restricted in certain countries
    either by patents or by copyrighted interfaces, the original copyright holder who
    places the Program under this License may add an explicit geographical
    distribution limitation excluding those countries, so that distribution is permitted
    only in or among countries not thus excluded. In such case, this License
    incorporates the limitation as if written in the body of this License.
    The Free Software Foundation may publish revised and/or new versions of the
    General Public License from time to time. Such new versions will be similar in
    spirit to the present version, but may differ in detail to address new problems or
    concerns.



  • Page 134

    General Notes

    Each version is given a distinguishing version number. If the Program specifies a
    version number of this License which applies to it and "any later version", you have
    the option of following the terms and conditions either of that version or of any
    later version published by the Free Software Foundation. If the Program does not
    specify a version number of this License, you may choose any version ever
    published by the Free Software Foundation.
    10. If you wish to incorporate parts of the Program into other free programs whose
    distribution conditions are different, write to the author to ask for permission. For
    software which is copyrighted by the Free Software Foundation, write to the Free
    Software Foundation; we sometimes make exceptions for this. Our decision will be
    guided by the two goals of preserving the free status of all derivatives of our free
    software and of promoting the sharing and reuse of software generally.

    11.

    12.

    NO WARRANTY
    BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO
    WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY
    APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING
    THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE
    PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER
    EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
    IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
    PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
    PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE
    PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL
    NECESSARY SERVICING, REPAIR OR CORRECTION.
    IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO
    IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY
    WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS
    PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING
    ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
    ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM
    (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING
    RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD
    PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY
    OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS
    BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

    134

    END OF TERMS AND CONDITIONS
    How to Apply These Terms to Your New Programs
    If you develop a new program, and you want it to be of the greatest possible use to the
    public, the best way to achieve this is to make it free software which everyone can
    redistribute and change under these terms.
    To do so, attach the following notices to the program. It is safest to attach them to the
    start of each source file to most effectively convey the exclusion of warranty; and each file
    should have at least the "copyright" line and a pointer to where the full notice is found.
    <one line to give the program's name and a brief idea of what it does.>
    Copyright (C) <year> <name of author>
    This program is free software; you can redistribute it and/or modify it under the
    terms of the GNU General Public License as published by the Free Software
    Foundation; either version 2 of the License, or (at your option) any later version.
    This program is distributed in the hope that it will be useful, but WITHOUT ANY
    WARRANTY; without even the implied warranty of MERCHANTABILITY or
    FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
    for more details.
    You should have received a copy of the GNU General Public License along with this
    program; if not, write to the Free Software Foundation, Inc., 51 Franklin Street,
    Fifth Floor, Boston, MA 02110-1301 USA.
    Also add information on how to contact you by electronic and paper mail.
    If the program is interactive, make it output a short notice like this when it starts in an
    interactive mode:
    Gnomovision version 69, Copyright (C) year name of author Gnomovision comes
    with ABSOLUTELY NO WARRANTY; for details type `show w'. This is free
    software, and you are welcome to redistribute it under certain conditions; type
    `show c' for details.
    The hypothetical commands `show w' and `show c' should show the appropriate parts
    of the General Public License. Of course, the commands you use may be called
    something other than `show w' and `show c'; they could even be mouse-clicks or menu
    items--whatever suits your program.
    You should also get your employer (if you work as a programmer) or your school, if any,
    to sign a "copyright disclaimer" for the program, if necessary. Here is a sample; alter the
    names:
    Yoyodyne, Inc., hereby disclaims all copyright interest in the program
    `Gnomovision' (which makes passes at compilers) written by James Hacker.



  • Page 135

    General Notes

    <signature of Ty Coon>, 1 April 1989
    Ty Coon, President of Vice
    This General Public License does not permit incorporating your program into
    proprietary programs. If your program is a subroutine library, you may consider it more
    useful to permit linking proprietary applications with the library. If this is what you want
    to do, use the GNU Lesser General Public License instead of this License.
    GNU LGPL
    This projector product includes the open source software programs which apply
    the GNU Lesser General Public License Version 2 or later version ("LGPL
    Programs").
    We provide the source code of the LGPL Programs until five (5) years after the
    discontinuation of same model of this projector product.
    If you desire to receive the source code of the LGPL Programs, please see the
    "EPSON Projector Contact List" in the User's Guide, and contact the customer
    support of your region.
    These LGPL Programs are WITHOUT ANY WARRANTY; without even the
    implied warranty of MERCHANTABILITY AND FITNESS FOR A
    PARTICULAR PURPOSE. See the GNU General Public License for more details.
    The list of LGPL Programs is as follows and the names of author are described in
    the source code of the LGPL Programs.
    LGPL Programs
    glibc-2.10
    SDL-1.2.13
    SDL-Image
    The GNU Lesser General Public License Version 2 is as follows. You also can see the
    GNU Lesser General Public License Version 2 at http://www.gnu.org/licenses/.
    GNU LESSER GENERAL PUBLIC LICENSE
    Version 2.1, February 1999
    Copyright (C) 1991, 1999 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor,
    Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim
    copies of this license document, but changing it is not allowed.
    [This is the first released version of the Lesser GPL. It also counts as the successor of the
    GNU Library Public License, version 2, hence the version number 2.1.]

    135

    Preamble
    The licenses for most software are designed to take away your freedom to share and
    change it. By contrast, the GNU General Public Licenses are intended to guarantee your
    freedom to share and change free software--to make sure the software is free for all its
    users.
    This license, the Lesser General Public License, applies to some specially designated
    software packages--typically libraries--of the Free Software Foundation and other
    authors who decide to use it. You can use it too, but we suggest you first think carefully
    about whether this license or the ordinary General Public License is the better strategy to
    use in any particular case, based on the explanations below.
    When we speak of free software, we are referring to freedom of use, not price. Our
    General Public Licenses are designed to make sure that you have the freedom to
    distribute copies of free software (and charge for this service if you wish); that you
    receive source code or can get it if you want it; that you can change the software and use
    pieces of it in new free programs; and that you are informed that you can do these
    things.
    To protect your rights, we need to make restrictions that forbid distributors to deny you
    these rights or to ask you to surrender these rights. These restrictions translate to certain
    responsibilities for you if you distribute copies of the library or if you modify it.
    For example, if you distribute copies of the library, whether gratis or for a fee, you must
    give the recipients all the rights that we gave you. You must make sure that they, too,
    receive or can get the source code. If you link other code with the library, you must
    provide complete object files to the recipients, so that they can relink them with the
    library after making changes to the library and recompiling it. And you must show them
    these terms so they know their rights.
    We protect your rights with a two-step method: (1) we copyright the library, and (2) we
    offer you this license, which gives you legal permission to copy, distribute and/or
    modify the library.
    To protect each distributor, we want to make it very clear that there is no warranty for
    the free library. Also, if the library is modified by someone else and passed on, the
    recipients should know that what they have is not the original version, so that the
    original author's reputation will not be affected by problems that might be introduced
    by others.



  • Page 136

    General Notes

    Finally, software patents pose a constant threat to the existence of any free program. We
    wish to make sure that a company cannot effectively restrict the users of a free program
    by obtaining a restrictive license from a patent holder. Therefore, we insist that any
    patent license obtained for a version of the library must be consistent with the full
    freedom of use specified in this license.
    Most GNU software, including some libraries, is covered by the ordinary GNU General
    Public License. This license, the GNU Lesser General Public License, applies to certain
    designated libraries, and is quite different from the ordinary General Public License. We
    use this license for certain libraries in order to permit linking those libraries into nonfree programs.
    When a program is linked with a library, whether statically or using a shared library, the
    combination of the two is legally speaking a combined work, a derivative of the original
    library. The ordinary General Public License therefore permits such linking only if the
    entire combination fits its criteria of freedom. The Lesser General Public License
    permits more lax criteria for linking other code with the library.
    We call this license the "Lesser" General Public License because it does Less to protect
    the user's freedom than the ordinary General Public License. It also provides other free
    software developers Less of an advantage over competing non-free programs. These
    disadvantages are the reason we use the ordinary General Public License for many
    libraries. However, the Lesser license provides advantages in certain special
    circumstances.
    For example, on rare occasions, there may be a special need to encourage the widest
    possible use of a certain library, so that it becomes a de-facto standard. To achieve this,
    non-free programs must be allowed to use the library. A more frequent case is that a free
    library does the same job as widely used non-free libraries. In this case, there is little to
    gain by limiting the free library to free software only, so we use the Lesser General Public
    License.
    In other cases, permission to use a particular library in non-free programs enables a
    greater number of people to use a large body of free software. For example, permission
    to use the GNU C Library in non-free programs enables many more people to use the
    whole GNU operating system, as well as its variant, the GNU/Linux operating system.
    Although the Lesser General Public License is Less protective of the users' freedom, it
    does ensure that the user of a program that is linked with the Library has the freedom
    and the wherewithal to run that program using a modified version of the Library.
    The precise terms and conditions for copying, distribution and modification follow.
    Pay close attention to the difference between a "work based on the library" and a "work
    that uses the library". The former contains code derived from the library, whereas the
    latter must be combined with the library in order to run.

    136

    GNU LESSER GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR
    COPYING, DISTRIBUTION AND MODIFICATION
    0. This License Agreement applies to any software library or other program which
    contains a notice placed by the copyright holder or other authorized party saying it
    may be distributed under the terms of this Lesser General Public License (also
    called "this License"). Each licensee is addressed as "you".
    A "library" means a collection of software functions and/or data prepared so as to
    be conveniently linked with application programs (which use some of those
    functions and data) to form executables.
    The "Library", below, refers to any such software library or work which has been
    distributed under these terms. A "work based on the Library" means either the
    Library or any derivative work under copyright law: that is to say, a work
    containing the Library or a portion of it, either verbatim or with modifications
    and/or translated straightforwardly into another language. (Hereinafter,
    translation is included without limitation in the term "modification".)
    "Source code" for a work means the preferred form of the work for making
    modifications to it. For a library, complete source code means all the source code
    for all modules it contains, plus any associated interface definition files, plus the
    scripts used to control compilation and installation of the library.
    Activities other than copying, distribution and modification are not covered by
    this License; they are outside its scope. The act of running a program using the
    Library is not restricted, and output from such a program is covered only if its
    contents constitute a work based on the Library (independent of the use of the
    Library in a tool for writing it). Whether that is true depends on what the Library
    does and what the program that uses the Library does.
    1. You may copy and distribute verbatim copies of the Library's complete source
    code as you receive it, in any medium, provided that you conspicuously and
    appropriately publish on each copy an appropriate copyright notice and
    disclaimer of warranty; keep intact all the notices that refer to this License and to
    the absence of any warranty; and distribute a copy of this License along with the
    Library.
    You may charge a fee for the physical act of transferring a copy, and you may at
    your option offer warranty protection in exchange for a fee.
    2.

    You may modify your copy or copies of the Library or any portion of it, thus
    forming a work based on the Library, and copy and distribute such modifications
    or work under the terms of Section 1 above, provided that you also meet all of these
    conditions:



  • Page 137

    General Notes

    a)
    b)

    The modified work must itself be a software library.
    You must cause the files modified to carry prominent notices stating that you
    changed the files and the date of any change.
    c) You must cause the whole of the work to be licensed at no charge to all third
    parties under the terms of this License.
    d) If a facility in the modified Library refers to a function or a table of data to be
    supplied by an application program that uses the facility, other than as an
    argument passed when the facility is invoked, then you must make a good
    faith effort to ensure that, in the event an application does not supply such
    function or table, the facility still operates, and performs whatever part of its
    purpose remains meaningful.
    (For example, a function in a library to compute square roots has a purpose
    that is entirely well-defined independent of the application. Therefore,
    Subsection 2d requires that any application-supplied function or table used
    by this function must be optional: if the application does not supply it, the
    square root function must still compute square roots.)
    These requirements apply to the modified work as a whole. If identifiable sections
    of that work are not derived from the Library, and can be reasonably considered
    independent and separate works in themselves, then this License, and its terms, do
    not apply to those sections when you distribute them as separate works. But when
    you distribute the same sections as part of a whole which is a work based on the
    Library, the distribution of the whole must be on the terms of this License, whose
    permissions for other licensees extend to the entire whole, and thus to each and
    every part regardless of who wrote it.
    Thus, it is not the intent of this section to claim rights or contest your rights to work
    written entirely by you; rather, the intent is to exercise the right to control the
    distribution of derivative or collective works based on the Library.
    In addition, mere aggregation of another work not based on the Library with the
    Library (or with a work based on the Library) on a volume of a storage or
    distribution medium does not bring the other work under the scope of this
    License.

    137

    3.

    4.

    5.

    You may opt to apply the terms of the ordinary GNU General Public License
    instead of this License to a given copy of the Library. To do this, you must alter all
    the notices that refer to this License, so that they refer to the ordinary GNU
    General Public License, version 2, instead of to this License. (If a newer version
    than version 2 of the ordinary GNU General Public License has appeared, then you
    can specify that version instead if you wish.) Do not make any other change in
    these notices.
    Once this change is made in a given copy, it is irreversible for that copy, so the
    ordinary GNU General Public License applies to all subsequent copies and
    derivative works made from that copy.
    This option is useful when you wish to copy part of the code of the Library into a
    program that is not a library.
    You may copy and distribute the Library (or a portion or derivative of it, under
    Section 2) in object code or executable form under the terms of Sections 1 and 2
    above provided that you accompany it with the complete corresponding machinereadable source code, which must be distributed under the terms of Sections 1 and
    2 above on a medium customarily used for software interchange.
    If distribution of object code is made by offering access to copy from a designated
    place, then offering equivalent access to copy the source code from the same place
    satisfies the requirement to distribute the source code, even though third parties
    are not compelled to copy the source along with the object code.
    A program that contains no derivative of any portion of the Library, but is
    designed to work with the Library by being compiled or linked with it, is called a
    "work that uses the Library". Such a work, in isolation, is not a derivative work of
    the Library, and therefore falls outside the scope of this License.
    However, linking a "work that uses the Library" with the Library creates an
    executable that is a derivative of the Library (because it contains portions of the
    Library), rather than a "work that uses the library". The executable is therefore
    covered by this License. Section 6 states terms for distribution of such executables.
    When a "work that uses the Library" uses material from a header file that is part of
    the Library, the object code for the work may be a derivative work of the Library
    even though the source code is not. Whether this is true is especially significant if
    the work can be linked without the Library, or if the work is itself a library. The
    threshold for this to be true is not precisely defined by law.



  • Page 138

    General Notes

    6.

    If such an object file uses only numerical parameters, data structure layouts and
    accessors, and small macros and small inline functions (ten lines or less in length),
    then the use of the object file is unrestricted, regardless of whether it is legally a
    derivative work. (Executables containing this object code plus portions of the
    Library will still fall under Section 6.)
    Otherwise, if the work is a derivative of the Library, you may distribute the object
    code for the work under the terms of Section 6. Any executables containing that
    work also fall under Section 6, whether or not they are linked directly with the
    Library itself.
    As an exception to the Sections above, you may also combine or link a "work that
    uses the Library" with the Library to produce a work containing portions of the
    Library, and distribute that work under terms of your choice, provided that the
    terms permit modification of the work for the customer's own use and reverse
    engineering for debugging such modifications.
    You must give prominent notice with each copy of the work that the Library is used
    in it and that the Library and its use are covered by this License. You must supply a
    copy of this License. If the work during execution displays copyright notices, you
    must include the copyright notice for the Library among them, as well as a
    reference directing the user to the copy of this License. Also, you must do one of
    these things:
    a) Accompany the work with the complete corresponding machine-readable
    source code for the Library including whatever changes were used in the work
    (which must be distributed under Sections 1 and 2 above); and, if the work is
    an executable linked with the Library, with the complete machine-readable
    "work that uses the Library", as object code and/or source code, so that the
    user can modify the Library and then relink to produce a modified executable
    containing the modified Library. (It is understood that the user who changes
    the contents of definitions files in the Library will not necessarily be able to
    recompile the application to use the modified definitions.)
    b) Use a suitable shared library mechanism for linking with the Library. A
    suitable mechanism is one that (1) uses at run time a copy of the library
    already present on the user's computer system, rather than copying library
    functions into the executable, and (2) will operate properly with a modified
    version of the library, if the user installs one, as long as the modified version is
    interface-compatible with the version that the work was made with.
    c) Accompany the work with a written offer, valid for at least three years, to give
    the same user the materials specified in Subsection 6a, above, for a charge no
    more than the cost of performing this distribution.

    138

    d)

    7.

    8.

    If distribution of the work is made by offering access to copy from a
    designated place, offer equivalent access to copy the above specified materials
    from the same place.
    e) Verify that the user has already received a copy of these materials or that you
    have already sent this user a copy.
    For an executable, the required form of the "work that uses the Library" must
    include any data and utility programs needed for reproducing the executable from
    it. However, as a special exception, the materials to be distributed need not include
    anything that is normally distributed (in either source or binary form) with the
    major components (compiler, kernel, and so on) of the operating system on which
    the executable runs, unless that component itself accompanies the executable.
    It may happen that this requirement contradicts the license restrictions of other
    proprietary libraries that do not normally accompany the operating system. Such a
    contradiction means you cannot use both them and the Library together in an
    executable that you distribute.
    You may place library facilities that are a work based on the Library side-by-side in
    a single library together with other library facilities not covered by this License,
    and distribute such a combined library, provided that the separate distribution of
    the work based on the Library and of the other library facilities is otherwise
    permitted, and provided that you do these two things:
    a) Accompany the combined library with a copy of the same work based on the
    Library, uncombined with any other library facilities. This must be
    distributed under the terms of the Sections above.
    b) Give prominent notice with the combined library of the fact that part of it is a
    work based on the Library, and explaining where to find the accompanying
    uncombined form of the same work.
    You may not copy, modify, sublicense, link with, or distribute the Library except as
    expressly provided under this License. Any attempt otherwise to copy, modify,
    sublicense, link with, or distribute the Library is void, and will automatically
    terminate your rights under this License. However, parties who have received
    copies, or rights, from you under this License will not have their licenses
    terminated so long as such parties remain in full compliance.



  • Page 139

    General Notes

    9.

    You are not required to accept this License, since you have not signed it. However,
    nothing else grants you permission to modify or distribute the Library or its
    derivative works. These actions are prohibited by law if you do not accept this
    License. Therefore, by modifying or distributing the Library (or any work based on
    the Library), you indicate your acceptance of this License to do so, and all its terms
    and conditions for copying, distributing or modifying the Library or works based
    on it.
    10. Each time you redistribute the Library (or any work based on the Library), the
    recipient automatically receives a license from the original licensor to copy,
    distribute, link with or modify the Library subject to these terms and conditions.
    You may not impose any further restrictions on the recipients' exercise of the
    rights granted herein. You are not responsible for enforcing compliance by third
    parties with this License.
    11. If, as a consequence of a court judgment or allegation of patent infringement or for
    any other reason (not limited to patent issues), conditions are imposed on you
    (whether by court order, agreement or otherwise) that contradict the conditions of
    this License, they do not excuse you from the conditions of this License. If you
    cannot distribute so as to satisfy simultaneously your obligations under this
    License and any other pertinent obligations, then as a consequence you may not
    distribute the Library at all. For example, if a patent license would not permit
    royalty-free redistribution of the Library by all those who receive copies directly or
    indirectly through you, then the only way you could satisfy both it and this License
    would be to refrain entirely from distribution of the Library.
    If any portion of this section is held invalid or unenforceable under any particular
    circumstance, the balance of the section is intended to apply, and the section as a
    whole is intended to apply in other circumstances.
    It is not the purpose of this section to induce you to infringe any patents or other
    property right claims or to contest validity of any such claims; this section has the
    sole purpose of protecting the integrity of the free software distribution system
    which is implemented by public license practices. Many people have made
    generous contributions to the wide range of software distributed through that
    system in reliance on consistent application of that system; it is up to the author/
    donor to decide if he or she is willing to distribute software through any other
    system and a licensee cannot impose that choice.
    This section is intended to make thoroughly clear what is believed to be a
    consequence of the rest of this License.

    139

    12. If the distribution and/or use of the Library is restricted in certain countries either
    by patents or by copyrighted interfaces, the original copyright holder who places
    the Library under this License may add an explicit geographical distribution
    limitation excluding those countries, so that distribution is permitted only in or
    among countries not thus excluded. In such case, this License incorporates the
    limitation as if written in the body of this License.
    13. The Free Software Foundation may publish revised and/or new versions of the
    Lesser General Public License from time to time. Such new versions will be similar
    in spirit to the present version, but may differ in detail to address new problems or
    concerns.
    Each version is given a distinguishing version number. If the Library specifies a
    version number of this License which applies to it and "any later version", you have
    the option of following the terms and conditions either of that version or of any
    later version published by the Free Software Foundation. If the Library does not
    specify a license version number, you may choose any version ever published by
    the Free Software Foundation.
    14. If you wish to incorporate parts of the Library into other free programs whose
    distribution conditions are incompatible with these, write to the author to ask for
    permission. For software which is copyrighted by the Free Software Foundation,
    write to the Free Software Foundation; we sometimes make exceptions for this.
    Our decision will be guided by the two goals of preserving the free status of all
    derivatives of our free software and of promoting the sharing and reuse of software
    generally.

    15.

    NO WARRANTY
    BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO
    WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY
    APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING
    THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE
    LIBRARY "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER
    EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
    IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
    PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
    PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY
    PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY
    SERVICING, REPAIR OR CORRECTION.



  • Page 140

    General Notes

    16.

    IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO
    IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY
    WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS
    PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING
    ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
    ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY
    (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING
    RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD
    PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY
    OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS
    BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

    END OF TERMS AND CONDITIONS
    How to Apply These Terms to Your New Libraries
    If you develop a new library, and you want it to be of the greatest possible use to the
    public, we recommend making it free software that everyone can redistribute and
    change. You can do so by permitting redistribution under these terms (or, alternatively,
    under the terms of the ordinary General Public License).
    To apply these terms, attach the following notices to the library. It is safest to attach them
    to the start of each source file to most effectively convey the exclusion of warranty; and
    each file should have at least the "copyright" line and a pointer to where the full notice is
    found.
    <one line to give the library's name and a brief idea of what it does.>
    Copyright (C) <year> <name of author>
    This library is free software; you can redistribute it and/or modify it under the
    terms of the GNU Lesser General Public License as published by the Free Software
    Foundation; either version 2.1 of the License, or (at your option) any later version.
    This library is distributed in the hope that it will be useful, but WITHOUT ANY
    WARRANTY; without even the implied warranty of MERCHANTABILITY or
    FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public
    License for more details.
    You should have received a copy of the GNU Lesser General Public License along
    with this library; if not, write to the Free Software Foundation, Inc., 51 Franklin
    Street, Fifth Floor, Boston, MA 02110-1301 USA
    Also add information on how to contact you by electronic and paper mail.

    140

    You should also get your employer (if you work as a programmer) or your school, if any,
    to sign a "copyright disclaimer" for the library, if necessary. Here is a sample; alter the
    names:
    Yoyodyne, Inc., hereby disclaims all copyright interest in the library `Frob' (a
    library for tweaking knobs) written by James Random Hacker.
    <signature of Ty Coon>, 1 April 1990
    Ty Coon, President of Vice
    That's all there is to it!
    BSD License (Berkeley Software Distribution License)
    This projector product includes the open source software program "University of
    California, Berkeley License (Berkeley Software Distribution License)" which applies
    the terms and conditions provided by owner of the copyright to the "BSD License".
    The "BSD License" are WITHOUT ANY WARRANTY; without even the implied
    warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
    List of BSD License programs
    busybox-1.13.4
    License terms of conditions of each program which are provided by owner of the
    copyright to the “BSD License” are as follows.
    Copyright (c) The Regents of the University of California. All rights reserved.
    This code is derived from software contributed to Berkeley by Kenneth Almquist.
    Redistribution and use in source and binary forms, with or without modification, are
    permitted provided that the following conditions are met:
    1.
    Redistributions of source code must retain the above copyright notice, this list of
    conditions and the following disclaimer.
    2.

    3.

    Redistributions in binary form must reproduce the above copyright notice, this
    list of conditions and the following disclaimer in the documentation and/or other
    materials provided with the distribution.
    Neither the name of the University nor the names of its contributors may be used
    to endorse or promote products derived from this software without specific prior
    written permission.



  • Page 141

    General Notes

    THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS "AS
    IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
    LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
    FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT
    SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
    INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
    DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
    SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
    BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
    LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
    (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF
    THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
    SUCH DAMAGE.
    libjpeg
    This projector product includes the open source software program "libjpeg" which
    applies the terms and conditions provided by owner of the copyright to the "libjpeg".
    The "libjpeg" are WITHOUT ANY WARRANTY; without even the implied warranty of
    MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
    List of libjpeg programs
    libjpeg-6b
    License terms of conditions of each program which are provided by owner of the
    copyright to the "libjpeg" are as follows.
    Copyright (C) 1994-1997, Thomas G. Lane. This file is part of the Independent JPEG
    Group's software. For conditions of distribution and use, see the accompanying
    README file.
    This distribution contains the sixth public release of the Independent JPEG Group's free
    JPEG software. You are welcome to redistribute this software and to use it for any
    purpose, subject to the conditions under LEGAL ISSUES, below.
    LEGAL ISSUES
    ============
    In plain English:
    1.
    We don't promise that this software works. (But if you find any bugs, please let us
    know!)
    2.
    You can use this software for whatever you want. You don't have to pay us.

    141

    3.

    You may not pretend that you wrote this software. If you use it in a program, you
    must acknowledge somewhere in your documentation that you've used the IJG
    code.
    In legalese:
    The authors make NO WARRANTY or representation, either express or implied, with
    respect to this software, its quality, accuracy, merchantability, or fitness for a particular
    purpose. This software is provided "AS IS", and you, its user, assume the entire risk as to
    its quality and accuracy.
    This software is copyright (C) 1991-1998, Thomas G. Lane. All Rights Reserved except
    as specified below.
    Permission is hereby granted to use, copy, modify, and distribute this software (or
    portions thereof) for any purpose, without fee, subject to these conditions:
    (1) If any part of the source code for this software is distributed, then this README
    file must be included, with this copyright and no-warranty notice unaltered; and
    any additions, deletions, or changes to the original files must be clearly indicated
    in accompanying documentation.
    (2) If only executable code is distributed, then the accompanying documentation
    must state that "this software is based in part on the work of the Independent JPEG
    Group".
    (3) Permission for use of this software is granted only if the user accepts full
    responsibility for any undesirable consequences; the authors accept NO
    LIABILITY for damages of any kind.
    These conditions apply to any software derived from or based on the IJG code, not just to
    the unmodified library. If you use our work, you ought to acknowledge us.
    Permission is NOT granted for the use of any IJG author's name or company name in
    advertising or publicity relating to this software or products derived from it. This
    software may be referred to only as "the Independent JPEG Group's software".
    We specifically permit and encourage the use of this software as the basis of commercial
    products, provided that all warranty or liability claims are assumed by the product
    vendor.
    ansi2knr.c is included in this distribution by permission of L. Peter Deutsch, sole
    proprietor of its copyright holder, Aladdin Enterprises of Menlo Park, CA. ansi2knr.c is
    NOT covered by the above copyright and conditions, but instead by the usual
    distribution terms of the Free Software Foundation; principally, that you must include
    source code if you redistribute it. (See the file ansi2knr.c for full details.) However, since
    ansi2knr.c is not needed as part of any program generated from the IJG code, this does
    not limit you more than the foregoing paragraphs do.



  • Page 142

    General Notes

    The Unix configuration script "configure" was produced with GNU Autoconf. It is
    copyright by the Free Software Foundation but is freely distributable. The same holds
    for its supporting scripts (config.guess, config.sub, ltconfig, ltmain.sh). Another
    support script, install-sh, is copyright by M.I.T. but is also freely distributable.
    It appears that the arithmetic coding option of the JPEG spec is covered by patents
    owned by IBM, AT&T, and Mitsubishi. Hence arithmetic coding cannot legally be used
    without obtaining one or more licenses. For this reason, support for arithmetic coding
    has been removed from the free JPEG software. (Since arithmetic coding provides only a
    marginal gain over the unpatented Huffman mode, it is unlikely that very many
    implementations will support it.) So far as we are aware, there are no patent restrictions
    on the remaining code.
    The IJG distribution formerly included code to read and write GIF files. To avoid
    entanglement with the Unisys LZW patent, GIF reading support has been removed
    altogether, and the GIF writer has been simplified to produce "uncompressed GIFs".
    This technique does not use the LZW algorithm; the resulting GIF files are larger than
    usual, but are readable by all standard GIF decoders.
    We are required to state that
    "The Graphics Interchange Format(c) is the Copyright property of CompuServe
    Incorporated. GIF(sm) is a Service Mark property of CompuServe Incorporated."
    libpng
    This projector product includes the open source software program "libpng" which
    applies the terms and conditions provided by owner of the copyright to the "libpng".
    The "libpng" are WITHOUT ANY WARRANTY; without even the implied warranty of
    MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
    List of libpng programs
    libpng-1.2.7
    License terms of conditions of each program which are provided by owner of the
    copyright to the "libpng" are as follows.
    For conditions of distribution and use, see copyright notice in png.h Copyright (c)
    1998-2004 Glenn Randers-Pehrson (Version 0.96 Copyright (c) 1996, 1997 Andreas
    Dilger) (Version 0.88 Copyright (c) 1995, 1996 Guy Eric Schalnat, Group 42, Inc.)
    This copy of the libpng notices is provided for your convenience. In case of any
    discrepancy between this copy and the notices in the file png.h that is included in the
    libpng distribution, the latter shall prevail.
    COPYRIGHT NOTICE, DISCLAIMER, and LICENSE:

    142

    If you modify libpng you may insert additional notices immediately following this
    sentence.
    libpng version 1.2.6, September 12, 2004, is Copyright (c) 2004 Glenn Randers-Pehrson,
    and is distributed according to the same disclaimer and license as libpng-1.2.5 with the
    following individual added to the list of Contributing Authors
    Cosmin Truta
    libpng versions 1.0.7, July 1, 2000, through 1.2.5 - October 3, 2002, are Copyright (c)
    2000-2002 Glenn Randers-Pehrson, and are distributed according to the same
    disclaimer and license as libpng-1.0.6 with the following individuals added to the list of
    Contributing Authors
    Simon-Pierre Cadieux
    Eric S. Raymond
    Gilles Vollant
    and with the following additions to the disclaimer:
    There is no warranty against interference with your enjoyment of the library or
    against infringement. There is no warranty that our efforts or the library will fulfill
    any of your particular purposes or needs. This library is provided with all faults,
    and the entire risk of satisfactory quality, performance, accuracy, and effort is with
    the user.
    libpng versions 0.97, January 1998, through 1.0.6, March 20, 2000, are Copyright (c)
    1998, 1999 Glenn Randers-Pehrson, and are distributed according to the same
    disclaimer and license as libpng-0.96, with the following individuals added to the list of
    Contributing Authors:
    Tom Lane
    Glenn Randers-Pehrson
    Willem van Schaik
    libpng versions 0.89, June 1996, through 0.96, May 1997, are Copyright (c) 1996, 1997
    Andreas Dilger Distributed according to the same disclaimer and license as libpng-0.88,
    with the following individuals added to the list of Contributing Authors:
    John Bowler
    Kevin Bracey
    Sam Bushell
    Magnus Holmgren
    Greg Roelofs
    Tom Tanner



  • Page 143

    General Notes

    libpng versions 0.5, May 1995, through 0.88, January 1996, are Copyright (c) 1995, 1996
    Guy Eric Schalnat, Group 42, Inc.
    For the purposes of this copyright and license, "Contributing Authors" is defined as the
    following set of individuals:
    Andreas Dilger
    Dave Martindale
    Guy Eric Schalnat
    Paul Schmidt
    Tim Wegner
    The PNG Reference Library is supplied "AS IS". The Contributing Authors and Group
    42, Inc. disclaim all warranties, expressed or implied, including, without limitation, the
    warranties of merchantability and of fitness for any purpose. The Contributing Authors
    and Group 42, Inc. assume no liability for direct, indirect, incidental, special, exemplary,
    or consequential damages, which may result from the use of the PNG Reference Library,
    even if advised of the possibility of such damage.
    Permission is hereby granted to use, copy, modify, and distribute this source code, or
    portions hereof, for any purpose, without fee, subject to the following restrictions:
    1.
    The origin of this source code must not be misrepresented.
    2.
    Altered versions must be plainly marked as such and must not be misrepresented
    as being the original source.
    3.

    This Copyright notice may not be removed or altered from any source or altered
    source distribution.
    The Contributing Authors and Group 42, Inc. specifically permit, without fee, and
    encourage the use of this source code as a component to supporting the PNG file format
    in commercial products. If you use this source code in a product, acknowledgment is not
    required but would be appreciated.
    A "png_get_copyright" function is available, for convenient use in "about" boxes and the
    like:
    printf("%s",png_get_copyright(NULL));
    Also, the PNG logo (in PNG format, of course) is supplied in the files "pngbar.png" and
    "pngbar.jpg (88x31) and "pngnow.png" (98x31).
    Libpng is OSI Certified Open Source Software. OSI Certified Open Source is a
    certification mark of the Open Source Initiative.

    143

    Glenn Randers-Pehrson
    glennrp@users.sourceforge.net
    September 12, 2004
    zlib
    This projector product includes the open source software program "zlib" which applies
    the terms and conditions provided by owner of the copyright to the "zlib".
    The "zlib" are WITHOUT ANY WARRANTY; without even the implied warranty of
    MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
    List of zlib programs
    zlib-1.1.4
    License terms of conditions of each program which are provided by owner of the
    copyright to the “zlib” are as follows.
    Copyright notice:
    (C) 1995-1998 Jean-loup Gailly and Mark Adler
    This software is provided 'as-is', without any express or implied warranty. In no
    event will the authors be held liable for any damages arising from the use of this
    software.
    Permission is granted to anyone to use this software for any purpose, including
    commercial applications, and to alter it and redistribute it freely, subject to the
    following restrictions:
    1.

    2.

    The origin of this software must not be misrepresented; you must not claim
    that you wrote the original software. If you use this software in a product, an
    acknowledgment in the product documentation would be appreciated but is
    not required.
    Altered source versions must be plainly marked as such, and must not be
    misrepresented as being the original software.

    3. This notice may not be removed or altered from any source distribution.
    Jean-loup Gailly
    Mark Adler
    jloup@gzip.org
    madler@alumni.caltech.edu
    If you use the zlib library in a product, we would appreciate *not* receiving lengthy legal
    documents to sign. The sources are provided for free but without warranty of any kind.
    The library has been entirely written by Jean-loup Gailly and Mark Adler; it does not
    include third-party code.



  • Page 144

    General Notes

    If you redistribute modified sources, we would appreciate that you include in the file
    ChangeLog history information documenting your changes.
    libmd5-rfc
    This projector product includes the open source software program "libmd5-rfc" which
    applies the terms and conditions provided by owner of the copyright to the "libmd5rfc".
    The "libmd5-rfc" are WITHOUT ANY WARRANTY; without even the implied
    warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
    List of libmd5-rfc programs
    libmd5-rfc
    License terms of conditions of each program which are provided by owner of the
    copyright to the "libmd5-rfc" are as follows.
    Copyright (C) 1999, 2002 Aladdin Enterprises. All rights reserved.
    This software is provided 'as-is', without any express or implied warranty. In no
    event will the authors be held liable for any damages arising from the use of this
    software.
    Permission is granted to anyone to use this software for any purpose, including
    commercial applications, and to alter it and redistribute it freely, subject to the
    following restrictions:
    1. The origin of this software must not be misrepresented; you must not claim
    that you wrote the original software. If you use this software in a product, an
    acknowledgment in the product documentation would be appreciated but is
    not required.
    2. Altered source versions must be plainly marked as such, and must not be
    misrepresented as being the original software.
    3. This notice may not be removed or altered from any source distribution.
    L. Peter Deutsch ghost@aladdin.com
    Independent implementation of MD5 (RFC 1321).
    This code implements the MD5 Algorithm defined in RFC 1321, whose text is available
    at
    http://www.ietf.org/rfc/rfc1321.txt
    The code is derived from the text of the RFC, including the test suite (section A.5) but
    excluding the rest of Appendix A. It does not include any code or documentation that is
    identified in the RFC as being copyrighted.

    144

    The original and principal author of md5.h is L. Peter Deutsch <ghost@aladdin.com>.
    Other authors are noted in the change history that follows (in reverse chronological
    order):
    2002-04-13 lpd Removed support for non-ANSI compilers; removed
    references to Ghostscript; clarified derivation from RFC 1321; now handles byte
    order either statically or dynamically.
    1999-11-04 lpd Edited comments slightly for automatic TOC extraction.
    1999-10-18 lpd Fixed typo in header comment (ansi2knr rather than md5);
    added conditionalization for C++ compilation from Martin Purschke
    <purschke@bnl.gov>.
    1999-05-03 lpd Original version.
    mDNSResponder
    This projector product includes the open source software program "mDNSResponder"
    which applies the following license terms "Apache License Version 2.0, January 2004".
    List of "mDNSResponder"
    mDNSResponder-107.6 (only mDNSResponderPosix is used)
    License terms “Apache License Version 2.0, January 2004" are as follows.
    Apache License
    Version 2.0, January 2004
    http://www.apache.org/licenses/
    TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION
    1.
    Definitions.
    "License" shall mean the terms and conditions for use, reproduction, and
    distribution as defined by Sections 1 through 9 of this document.
    "Licensor" shall mean the copyright owner or entity authorized by the copyright
    owner that is granting the License.
    "Legal Entity" shall mean the union of the acting entity and all other entities that
    control, are controlled by, or are under common control with that entity. For the
    purposes of this definition, "control" means (i) the power, direct or indirect, to
    cause the direction or management of such entity, whether by contract or
    otherwise, or (ii) ownership of fifty percent (50%) or more of the outstanding
    shares, or (iii) beneficial ownership of such entity.



  • Page 145

    General Notes

    2.

    "You" (or "Your") shall mean an individual or Legal Entity exercising permissions
    granted by this License.
    "Source" form shall mean the preferred form for making modifications, including
    but not limited to software source code, documentation source, and configuration
    files.
    "Object" form shall mean any form resulting from mechanical transformation or
    translation of a Source form, including but not limited to compiled object code,
    generated documentation, and conversions to other media types.
    "Work" shall mean the work of authorship, whether in Source or Object form,
    made available under the License, as indicated by a copyright notice that is
    included in or attached to the work (an example is provided in the Appendix
    below).
    "Derivative Works" shall mean any work, whether in Source or Object form, that is
    based on (or derived from) the Work and for which the editorial revisions,
    annotations, elaborations, or other modifications represent, as a whole, an
    original work of authorship. For the purposes of this License, Derivative Works
    shall not include works that remain separable from, or merely link (or bind by
    name) to the interfaces of, the Work and Derivative Works thereof.
    "Contribution" shall mean any work of authorship, including the original version
    of the Work and any modifications or additions to that Work or Derivative Works
    thereof, that is intentionally submitted to Licensor for inclusion in the Work by
    the copyright owner or by an individual or Legal Entity authorized to submit on
    behalf of the copyright owner. For the purposes of this definition, "submitted"
    means any form of electronic, verbal, or written communication sent to the
    Licensor or its representatives, including but not limited to communication on
    electronic mailing lists, source code control systems, and issue tracking systems
    that are managed by, or on behalf of, the Licensor for the purpose of discussing and
    improving the Work, but excluding communication that is conspicuously marked
    or otherwise designated in writing by the copyright owner as "Not a
    Contribution."
    "Contributor" shall mean Licensor and any individual or Legal Entity on behalf of
    whom a Contribution has been received by Licensor and subsequently
    incorporated within the Work.
    Grant of Copyright License. Subject to the terms and conditions of this License,
    each Contributor hereby grants to You a perpetual, worldwide, non-exclusive,
    no-charge, royalty-free, irrevocable copyright license to reproduce, prepare
    Derivative Works of, publicly display, publicly perform, sublicense, and distribute
    the Work and such Derivative Works in Source or Object form.

    145

    3.

    4.

    Grant of Patent License. Subject to the terms and conditions of this License, each
    Contributor hereby grants to You a perpetual, worldwide, non-exclusive, nocharge, royalty-free, irrevocable (except as stated in this section) patent license to
    make, have made, use, offer to sell, sell, import, and otherwise transfer the Work,
    where such license applies only to those patent claims licensable by such
    Contributor that are necessarily infringed by their Contribution(s) alone or by
    combination of their Contribution(s) with the Work to which such
    Contribution(s) was submitted. If You institute patent litigation against any entity
    (including a cross-claim or counterclaim in a lawsuit) alleging that the Work or a
    Contribution incorporated within the Work constitutes direct or contributory
    patent infringement, then any patent licenses granted to You under this License
    for that Work shall terminate as of the date such litigation is filed.
    Redistribution. You may reproduce and distribute copies of the Work or
    Derivative Works thereof in any medium, with or without modifications, and in
    Source or Object form, provided that You meet the following conditions:
    (a) You must give any other recipients of the Work or Derivative Works a copy
    of this License; and
    (b) You must cause any modified files to carry prominent notices stating that
    You changed the files; and
    (c) You must retain, in the Source form of any Derivative Works that You
    distribute, all copyright, patent, trademark, and attribution notices from the
    Source form of the Work, excluding those notices that do not pertain to any
    part of the Derivative Works; and
    (d) If the Work includes a "NOTICE" text file as part of its distribution, then any
    Derivative Works that You distribute must include a readable copy of the
    attribution notices contained within such NOTICE file, excluding those
    notices that do not pertain to any part of the Derivative Works, in at least one
    of the following places: within a NOTICE text file distributed as part of the
    Derivative Works; within the Source form or documentation, if provided
    along with the Derivative Works; or, within a display generated by the
    Derivative Works, if and wherever such third-party notices normally appear.
    The contents of the NOTICE file are for informational purposes only and do
    not modify the License. You may add Your own attribution notices within
    Derivative Works that You distribute, alongside or as an addendum to the
    NOTICE text from the Work, provided that such additional attribution
    notices cannot be construed as modifying the License.



  • Page 146

    General Notes

    5.

    6.

    7.

    8.

    You may add Your own copyright statement to Your modifications and may
    provide additional or different license terms and conditions for use, reproduction,
    or distribution of Your modifications, or for any such Derivative Works as a
    whole, provided Your use, reproduction, and distribution of the Work otherwise
    complies with the conditions stated in this License.
    Submission of Contributions. Unless You explicitly state otherwise, any
    Contribution intentionally submitted for inclusion in the Work by You to the
    Licensor shall be under the terms and conditions of this License, without any
    additional terms or conditions.
    Notwithstanding the above, nothing herein shall supersede or modify the terms of
    any separate license agreement you may have executed with Licensor regarding
    such Contributions.
    Trademarks. This License does not grant permission to use the trade names,
    trademarks, service marks, or product names of the Licensor, except as required
    for reasonable and customary use in describing the origin of the Work and
    reproducing the content of the NOTICE file.
    Disclaimer of Warranty. Unless required by applicable law or agreed to in writing,
    Licensor provides the Work (and each Contributor provides its Contributions) on
    an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY
    KIND, either express or implied, including, without limitation, any warranties or
    conditions of TITLE, NON-INFRINGEMENT, MERCHANTABILITY, or
    FITNESS FOR A PARTICULAR PURPOSE. You are solely responsible for
    determining the appropriateness of using or redistributing the Work and assume
    any risks associated with Your exercise of permissions under this License.
    Limitation of Liability. In no event and under no legal theory, whether in tort
    (including negligence), contract, or otherwise, unless required by applicable law
    (such as deliberate and grossly negligent acts) or agreed to in writing, shall any
    Contributor be liable to You for damages, including any direct, indirect, special,
    incidental, or consequential damages of any character arising as a result of this
    License or out of the use or inability to use the Work (including but not limited to
    damages for loss of goodwill, work stoppage, computer failure or malfunction, or
    any and all other commercial damages or losses), even if such Contributor has
    been advised of the possibility of such damages.

    146

    9.

    Accepting Warranty or Additional Liability. While redistributing the Work or
    Derivative Works thereof, You may choose to offer, and charge a fee for,
    acceptance of support, warranty, indemnity, or other liability obligations and/or
    rights consistent with this License. However, in accepting such obligations, You
    may act only on Your own behalf and on Your sole responsibility, not on behalf of
    any other Contributor, and only if You agree to indemnify, defend, and hold each
    Contributor harmless for any liability incurred by, or claims asserted against, such
    Contributor by reason of your accepting any such warranty or additional liability.

    END OF TERMS AND CONDITIONS
    APPENDIX: How to apply the Apache License to your work.
    To apply the Apache License to your work, attach the following boilerplate notice,
    with the fields enclosed by brackets "[]" replaced with your own identifying
    information. (Don't include the brackets!) The text should be enclosed in the
    appropriate comment syntax for the file format. We also recommend that a file or
    class name and description of purpose be included on the same "printed page" as
    the copyright notice for easier identification within third-party archives.
    Copyright [yyyy][name of copyright owner]
    Licensed under the Apache License, Version 2.0 (the "License");
    you may not use this file except in compliance with the License.
    You may obtain a copy of the License at
    http://www.apache.org/licenses/LICENSE-2.0
    Unless required by applicable law or agreed to in writing, software distributed under the
    License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR
    CONDITIONS OF ANY KIND, either express or implied.
    See the License for the specific language governing permissions and limitations under
    the License.



  • Page 147

    Index

    147

    A
    A/V Mute ...................................................... 51
    Abs. Color Temp. ........................................ 70
    Air exhaust vent ........................................... 10
    Air filter replacement period ................... 106
    Aspect ...................................................... 40, 72
    Auto H/V-Keystone .................................... 73
    Auto Iris .................................................. 39, 70
    Auto Setup .................................................... 71

    Control Panel Lock ............................... 64, 73
    Cross .............................................................. 54
    Customized ................................................... 39

    Direct Power On .......................................... 75
    Display ........................................................... 74
    Display Background .................................... 74
    Display order ................................................ 51
    Display Settings ............................................ 50
    Distance ...................................................... 118
    Document camera ..................................... 110
    Dynamic ........................................................ 38

    I
    Image menu .................................................. 70
    Indicators ...................................................... 88
    Info menu ..................................................... 84
    Input Signal ............................................ 71, 84
    IP Address ..................................................... 82

    E

    C
    Ceiling ..................................................... 19, 74
    Ceiling mount fixing points ....................... 12
    Cleaning ...................................................... 101
    Cleaning the air filter and air intake vent
    ........................................................................ 101
    Cleaning the Projector's Surface .............. 101
    Color Adjustment ........................................ 70
    Color Mode ............................................ 38, 70
    Color Saturation .......................................... 70
    Computer port ............................................. 11
    Configuration menu .................................... 67
    Connection mode ........................................ 79
    Consumables .............................................. 110
    Continuous ................................................... 51
    Contrast ........................................................ 70
    Control panel ............................................... 13

    HDMI port ................................................... 11
    HDMI Video Range .................................... 71
    Help function ............................................... 87
    High Altitude Mode .................................... 75
    How to replace the air filter ..................... 106
    How to replace the lamp ........................... 104

    D

    B
    Basic menu .................................................... 78
    Blackboard .................................................... 39
    Brightness ..................................................... 70

    H

    Email Address .............................................. 82
    ESC/VP21 ................................................... 114
    Extended menu ............................................ 74
    E-Zoom ......................................................... 53

    K
    Keystone ........................................................ 73

    L

    F
    Focus button ................................................. 14
    Focus ring ..................................................... 10
    Foot adjust lever ........................................... 10
    Freeze ............................................................. 52
    Front ........................................................ 19, 74
    Front adjustable foot ................................... 10
    Full Lock ....................................................... 64

    G
    Gateway Address ......................................... 79

    Lamp cover ................................................... 11
    Lamp hours ................................................... 84
    Lamp indicator ............................................. 88
    Lamp replacement period ........................ 103
    Language ....................................................... 75
    Lens Cover Timer ........................................ 75
    Link 21L ...................................................... 114

    M
    Mail Notification ................................. 82, 113
    Mail Notification menu .............................. 82
    Messages ....................................................... 74
    Monitor Displays ....................................... 121



  • Page 148

    Index

    148

    Projection ...................................................... 74
    Projector ID ............................................ 57, 75
    Projector keyword ....................................... 78
    Projector Name ............................................ 78
    Projector Setup ........................................... 111

    Mouse pointer .............................................. 54
    Multi-screen ........................................... 58, 75

    N
    Network Configuration ..............................
    Network information ..................................
    Network menu .............................................
    Noise Reduction ...........................................

    76
    76
    76
    71

    O

    Sharpness ...................................................... 70
    Signal menu .................................................. 71
    Sleep Mode ................................................... 75
    Slideshow ................................................ 46, 49
    SMTP Server ................................................. 82
    SNMP .......................................................... 113
    Soft keyboard ................................................ 77
    Source ............................................................ 84
    Source Search ......................................... 13, 27
    Specifications ............................................. 123
    Sports ............................................................. 38
    sRGB .............................................................. 38
    SSID ............................................................... 79
    Standby Mode .............................................. 75
    Startup Screen .............................................. 74
    Storage temperature .................................. 123
    Subnet Mask ................................................. 79
    Supported Monitor Displays .................... 121
    Sync Info ....................................................... 84
    Sync. ............................................................... 71

    Q
    Quick Corner ............................................... 73

    R
    Operating temperature ............................. 123
    Operation ...................................................... 75
    Optional accessories .................................. 110
    Overheating .................................................. 89

    Reading Mail .............................................. 113
    Rear .......................................................... 19, 74
    Rear feet ........................................................ 12
    Rear screen .................................................... 19
    Refresh Rate .................................................. 84
    Remote control ............................................ 14
    remote control ID ........................................ 57
    Remote receiver ..................................... 10, 12
    Replacing batteries ....................................... 17
    Reset All ........................................................ 85
    Reset menu ............................................. 83, 84
    Resetting the lamp operating time
    .................................................................. 85, 106
    Resolution ..................................................... 84
    Rotating images ........................................... 47

    P
    Part Names and Functions ......................... 10
    Password protect .......................................... 62
    Password protect sticker ............................. 63
    Photo ............................................................. 38
    PJLink .......................................................... 117
    PJLink Password .......................................... 78
    Pointer ........................................................... 52
    Pointer Shape ............................................... 73
    Port Number ................................................ 82
    Position ......................................................... 71
    Power Consumption ................................... 73
    Power indicator ............................................ 88
    Power inlet .................................................... 11
    Power On Protect ........................................ 62
    Presentation ........................................... 38, 45
    Problem Solving ........................................... 88
    Progressive .................................................... 71

    T

    S
    Screen size ................................................... 118
    Screen switching time ................................. 51
    Security menu .............................................. 80
    Security slot .................................................. 12
    Select Drive ................................................... 47
    Settings menu ............................................... 73

    Temp indicator ............................................
    Test Pattern ..................................................
    Theatre ..........................................................
    Tint ................................................................
    Tracking ........................................................

    88
    74
    38
    70
    71

    USB (Type A) port .......................................
    USB (TypeB) port ........................................
    USB Type B ...................................................
    User Button ..................................................

    11
    11
    75
    73

    U



  • Page 149

    Index

    User's Logo ................................................... 60
    User's Logo Protect ...................................... 62

    V
    Video port ..................................................... 11
    Video Signal ........................................... 71, 84
    Volume .......................................................... 73

    W
    Web Browser .............................................. 111
    Web Control ............................................... 111
    Web Control Password ............................... 78
    Web Remote ............................................... 111
    Whiteboard ................................................... 39
    Wide-screen projection .............................. 40
    Wireless LAN indicator .............................. 10
    Wireless LAN menu .................................... 79
    Wireless LAN Power ................................... 79
    Wireless LAN system .................................. 79
    Wireless LAN unit cover ............................ 10
    Wireless mouse function ............................ 54

    Z
    Zoom ring ..................................................... 10

    149






Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Epson EB-1760W wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Holen Sie sich Ihr Benutzerhandbuch per E-Mail

Geben Sie Ihre E-Mail-Adresse ein, um das Handbuch zu erhalten von Epson EB-1760W in der Sprache / Sprachen: Englisch als Anhang in Ihrer E-Mail.

Das Handbuch ist 11,29 mb groß.

 

Sie erhalten das Handbuch in Ihrer E-Mail innerhalb von Minuten. Wenn Sie keine E-Mail erhalten haben, haben Sie wahrscheinlich die falsche E-Mail-Adresse eingegeben oder Ihre Mailbox ist zu voll. Darüber hinaus kann es sein, dass Ihr ISP eine maximale Größe für E-Mails empfangen kann.

Andere Handbücher von Epson EB-1760W

Epson EB-1760W Bedienungsanleitung - Deutsch - 157 seiten

Epson EB-1760W Bedienungsanleitung - Holländisch - 157 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info