Bedienungsanleitung Felisatti AF180 (Seite 3 von 45) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

502483

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

MACHINE-SPECIFIC SAFETY WARNINGS

Safety Warnings Common for Grinding, Sanding, Wire

Brushing or Abrasive Cutting-Off Operations:

a) This power tool is intended to function as a grinder,

sander, wire brush, or cut-off tool. Read all safety warnings,

instructions, illustrations and specications provided with this

power tool. Failure to follow all instructions listed below may

result in electric shock, re and/or serious injury.

b) Operations such as polishing are not recommended to

be performed with this power tool. Operations for which the

power tool was not designed may create a hazard and cause

personal injury.

c) Do not use accessories which are not specically designed

and recommended by the tool manufacturer. Just because

the accessory can be attached to your power tool, it does not

assure safe operation.

d )The rated speed of the accessory must be at least equal to

the maximum speed marked on the power tool. Accessories

running faster than their rated speed can break and y

apart.

e) The outside diameter and the thickness of your accessory

must be within the capacity rating of your power tool.

Incorrectly sized accessories cannot be adequately guarded

or controlled.

f) The arbour size of wheels, anges, backing pads or any

other accessory must properly t the spindle of the power

tool. Accessories with arbour holes that do not match the

mounting hardware of the power tool will run out of balance,

vibrate excessively and may cause loss of control.

g) Do not use a damaged accessory. Before each use inspect

the accessory such as abrasive wheels for chips and cracks,

backing pad for cracks, tear or excess wear, wire brush for

loose or cracked wires. If power tool or accessory is dropped,

inspect for damage or install an undamaged accessory. After

inspecting and installing an accessory, position yourself and

bystanders away from the plane of the rotating accessory

and run the power tool at maximum noload speed for one

minute. Damaged accessories will normally break apart

during this test time.

h) Wear personal protective equipment. Depending on

application, use face shield, safety goggles or safety

glasses.

As appropriate, wear dust mask, hearing protectors, gloves

and shop apron capable of stopping small abrasive or

workpiece fragments. The eye protection must be capable of

stopping ying debris generated by various operations. The

dust mask or respirator must be capable of ltrating particles

generated by your operation. Prolonged exposure to high

intensity noise may cause hearing loss.

i) Keep bystanders a safe distance away from work area.

Anyone entering the work area must wear personal protective

equipment. Fragments of workpiece or of a broken accessory

may y away and cause injury beyond immediate area of

operation.

j) Hold power tool by insulated gripping surfaces, when

performing an operation where the cutting accessory may

contact hidden wiring or its own cord. Cutting accessory

contacting a „live“ wire may make exposed metal parts of

the power tool „live“ and could give the operator an electric

shock.

k) Position the cord clear of the spinning accessory. If you

lose control, the cord may be cut or snagged and your hand

or arm may be pulled into the spinning accessory.

l) Never lay the power tool down until the accessory has

come to a complete stop. The spinning accessory may grab

the surface and pull the power tool out of your control.

m) Do not run the power tool while carrying it at your side.

Accidental contact with the spinning accessory could snag

your clothing, pulling the accessory into your body.

n) Regularly clean the power tool’s air vents. The motor’s

fan will draw the dust inside the housing and excessive

accumulation of powdered metal may cause electrical

hazards.

o) Do not operate the power tool near ammable materials.

Sparks could ignite these materials.

p) Do not use accessories that require liquid coolants. Using

water or other liquid coolants may result in electrocution or

shock.

Kickback and related warnings

Kickback is a sudden reaction to a pinched or snagged

rotating wheel.

Pinching or snagging causes rapid stalling of the rotating

wheel which in turn causes the uncontrolled power tool to be

forced in the direction opposite of the wheel‘s rotation at the

point of the binding.

For example, if an abrasive wheel is snagged or pinched by

the workpiece, the edge of the wheel that is entering into the

pinch point can dig into the surface of the material causing

the wheel to climb out or kick out. The wheel may either jump

toward or away from the operator, depending on direction

of the wheel’s movement at the point of pinching. Abrasive

wheels may also break under these conditions.

Kickback is the result of saw misuse and/or incorrect

operating procedures or conditions and can be avoided by

taking proper precautions as given below.

a) Maintain a rm grip on the power tool and position your

body and arm to allow you to resist kickback forces. Always

use auxiliary handle, if provided, for maximum control over

kickback or torque reaction during start-up. The operator

can control torque reactions or kickback forces, if proper

precautions are taken.

b) Never place your hand near the rotating accessory.

Accessory may kickback over your hand.

c) Do not position your body in the area where power tool

will move if kickback occurs. Kickback will propel the tool in

direction opposite to the wheel’s movement at the point of

snagging.

d) Use special care when working corners, sharp edges, etc.

Avoid bouncing and snagging the accessory. Corners, sharp

edges or bouncing have a tendency to snag the rotating

accessory and cause loss of control or kickback.

e) Do not attach a saw chain, woodcarving blade or toothed

saw blade. Such blades create frequent kickback and loss

of control.

Safety Warnings Specic for Grinding and Abrasive Cutting-

Off Operations:

a) Use only wheel types that are recommended for your

power tool and the specic guard designed for the selected

wheel. Wheels for which the power tool was not designed

cannot be adequately guarded and are unsafe.

b) The guard must be securely attached to the power tool

and positioned for maximum safety, so the least amount

of wheel is exposed towards the operator. The guard helps to

protect operator from broken wheel fragments and accidental

contact with wheel.

c) Wheels must be used only for recommended applications.

For example: do not grind with the side of cut-off wheel.

Abrasive cut-off wheels are intended for peripheral grinding,

side forces applied to these wheels may cause them to

shatter.

d) Always use undamaged wheel anges that are of correct

size and shape for your selected wheel. Proper wheel

anges support the wheel thus reducing the possibility of

Felisatti AF180 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info